Mounts more - Import export

Instead of mounting one or more Transporters to each die, the PSKS features one unit only – mounted directly to the face of the bolster. A heightadjustable mounting bracket allows flexible usage with multiple tools and dies. The only extra thing needed will be scrap trays in different sizes On the left and right end of the system, heightadjustable brackets with linear bearings support a crossmounted aluminum profile. The profile is fastened with standardized clamping brackets and will transfer the motion over the whole width Numerous trays can be mounted. Two rugged nylon Ushape clamps are permanently fastened to each of the trays. The fasteners are designed to slide and fit snug onto the aluminum profile so that exchanging of trays is just a matter of seconds. The length and width of the tray is determined by the size of the die slot.

Ball joint monitor mounting Even more degrees of freedom through a ball joint socket Feature: max. load capacity 10 kg (static) 60° free swivelling reducing bushes available (round 20 and 25mm, square 20mm)

Roll Feeds with servo drive They revolutionized the advancement of strip material in the early 1980’s. However, Air Feeds became far from obsolete over 90 different GSWModels show that even today demands for costs, material geometry or composition as well as mounting situations more than justify this technology.

11 torque range from ± 0 - 0,5 Nm to ± 0 - 1000 Nm current and voltage output measurement accuracy ≤ 0.25% contactless signal transmission proven strain gauge technology built-in signal amplifier simple power supply universally applicable RPM measurement optional The new features: more versatile mounting options torsion shaft stainless mistake-proof installation oriented mounting large coupling selection The torque sensors of the DRBL series are a further development of our DRBK series and are suitable for use in the laboratory and for industrial environments with their compact dimensions and diverse mounting options. A factory calibration certificate with 25% increments (left, right) is included in the scope of delivery. The non-contact transmission of the measurement signal and the supply energy enables low-wear and m aintenance-free continuous operation.

Systems & Modules SMS designs, manufactures and supplies complete systems & modules for evaporation, drying and membrane applications. Our scope of supply includes: Consulting / Feasibility Studies Pilot Test Process Design Plant Engineering Project Management Procurement / Manufacturing / Delivery Erection / Installation Start-Up / Commissioning After-Sales Service Skid-Mounted Modules For more than 40 years SMS has been supplying skid-mounted units for the benifit of our customers. The skids are fully assembled, including piping, wiring and testing in the SMS Workshop or in our partners´ workshop. The modular design significantly reduces the required amount of work for assembly and start-up which minimizes the downtime of the existing plant equipment and - as a result - just minor effects occur on the current production.

n the micro and micro-drive sector, IAI offers small mini slider types that easily replace pneumatic cylinders due to their identical design and simple control mode. They are suitable for mounting fixtures, workpiece positioning, table motion and many other applications. In the RCP3 series, the smallest models are available as a slider types with sliding spindle. The latest developments are the space-saving mini slider types of the RCA2 series with 24 V servo motor.

This stainless steel rod, which is manufactured completely from stainless steel (Ø 42 mm), is used to install building components and (sub)structures on a roof surface. Our ABS UniMount is a flexible solution which can be used to install solar panels and photovoltaic modules, air conditioning systems and similar components. It can can either be installed on a concrete or steel surface. Base plate (130 x 130 mm) + welded-on mounting rod (Ø 42 mm) Female thread (M 10) at the top end For steel surfaces with a depth of at least 5 mm For horizontal and vertical loads of max. 3 kN Incl. stainless steel installation set

A HIGHLY EFFICIENT METHOD WITHOUT THE RISK OF WORK PIECES DAMAGING EACH OTHER Compared to standard mass finishing systems the newly developed M-TMD machine range finish high-value components 10 to 20 times more efficiently! By mounting the work pieces individually to workstations, which are part of a rotating carousel, you can process up to 18 work pieces in one single batch without risking part-on-part impingement. Different workstation angles - relative to their vertical position - allow the individual adaption of the machine parameters to your work pieces and guarantee absolutely stable finishing processes with excellent and repeatable results. APPLICATIONS: Orthopedic implants (medical engineering) Turbine blades (for airplanes as well stationary turbines) Precision components, for example, for pumps and compressors Work pieces made from tungsten carbide and other hard metals Fan wheels for turbo chargers (automotive industry) Sintered components, etc.