Temperature regulators - Import export

Technichal data: Accuracy ± 3°C at -50°C to 20°C ± 1% or 1°C at 20°C to 500°C ± 1.5% or 2°C at 500°C to 1,000°C ± 2% at 1,000°C to 1,850°C Reproducibility ± 1.5°C at -50°C to 20°C ± 0.5% or ± 0.5°C at 20 °C to 1,000 °C ± 1% at 1,000°C to 1,850 °C Optical resolution (D:S): 75:1 Smallest measurement spot: 18 mm @ 1,350 mm Temperature range: -50°C to +1,850°C Reaction time: < 150 ms Spectral sensivity: 8 ~ 14 µm Laser class: Klasse 2 (II) Wavelength: 630 ~ 670 nm Power: <1 mW Display: LCD, monochrome Temperature range (contact-temperature sensor): 50°C to +300°C Accuracy (contact-temperature sensor): ±1,5% or ± 3°C Reproducibility (contact-temperature sensor): ± 1,5% Operating conditions (operation): 0°C to 50°C, 10% to 90% RH Operating conditions (storage): -10°C to 60°C, < 80% RH (non-condensing) Power supply (internal): 9 V IEC 6LR61 Power supply (external): via USB

Temperature measuring strips, for example, are stuck to components that heat up under load. The measuring strip shows the maximum temperature reached after the component has cooled down. This means that the maximum temperature of the component can be read off quickly and inexpensively.

Ex thermostat or temperature regulator - Ex room thermostat - Temperature regulator for gas or surface temperature - Ex temperature limiter Ex zone 1 and 2

Control panels for safety monitoring and temperature regulation, for process heaters - Thyristor control panel - Interface to PLC - SIL calculation - Ex control panels for installation in hazardous areas

The precision RTD simulator is used where measuring instruments or controlling means with high precision must be examined or calibrated. The simulator is suitable for calibration laboratory and service centers which need a computer-controlled resistance decade for the automation of calibration procedures. All standard platinum and nickel RTD can be simulated with very high accuracy according to scales ITS 90 or IPTS 68. Temperature regulators, transducers etc. often supply a pulsed signal current in order to reduce the self-heating of the RTD. Devices with electronic simulation of RTD are therefore inclined to swinging and do not function with this application. Features: — Simulation of Pt100, Pt200, Pt500, Pt1000, Ni100 and Ni1000 sensors — Accuracy 0.02 °C — Temperature scales ITS 90, IPTS 68 — Real Ohm simulation — Control manually or remotely via RS232/IEEE488/USB Converter

ELECTRICAL SPACE HEATER TDS 120 RProfessional heating for large building areas: With the TDS 120 R and a full 30 kW heating force Owing to 30 kW of heating power, the most powerful model of the TDS-R series comes with convenient spare capacity for the permanent heating of larger rooms and is hence especially suited for temperature control in larger building sections. Accommodated in a comfortably transportable and stable carriage construction with ball-bearing wheels, the fully galvanized, coated steel sheet housing of the electrical space heater TDS 120 R houses high-quality corrosion-protected stainless steel heating elements, which immediately after switching on generate formidable heat flowing out in large volumes via the powerful air circulating follow-up fan. The desired temperature can be regulated as needed via the integrated infinitely variable thermostat and the heating capacity can be increased in two stages up to 30 kW for maximum selected warmth.

ELECTRIC HEATER FAN TDS 120The thermal power plant among the TDS electric heater fans With a hefty 30 kW of heating power the TDS 120 is the undisputed No. 1 among the popular TDS electric heater fans from Trotec and offers you convenient spare capacity for the permanent heating of larger rooms or for temperature control in large-volume building sections. Owing to the integrated thermostat control, the generated warm air current can be infinitely adjusted to the desired temperature and regulated in line with demand via a two-stage power control for space-filling temperature control. And since our distinctive logo has been printed on the outside, we have also incorporated distinct extras inside, which make all the difference to conventional standard electric heater fans.

Due to its high air flow rate and advanced PTC heater battery technology, the high-performance rapid heater TDS 30 M is ideally suited for quickly heating large, cold rooms. Whether for use in a workshop, in living or working spaces – the combination of a robust construction, sound workmanship and discreet design harmoniously integrates in any environment, and the thermally insulated carrying handle makes the device quick and easy to transport. The desired temperature can be regulated as needed via the integrated infinitely variable thermostat of the TDS 30 M. For more targeted warmth, the heating capacity can be increased in two stages up to 5 kW. If required, the fan can also be used in sole fan operation without heating function.

How do we improve the durability and performance of products? Through our production of heating mats for lithium-ion batteries and other batteries, we also indirectly contribute to the conservation of resources. In this way, the batteries are better protected against strong or fluctuating temperature influences. This means that they are less prone to failure and have a significantly longer service life and performance. Preheating, warm up or heating in continuous operation The heating mats are equipped with a performance tailored to the customer and regulate the temperature of the batteries and rechargeable batteries according to the necessary conditions. With optional equipment such as self-adhesive foil (one-sided or double-sided foil lamination), these can be attached to the battery or the block super easily. Application ✔️ in electric cars & hybrid vehicles ✔️ for electric commercial vehicles ✔️ for electric industrial trucks ✔️ other battery-powered industrial applications

The latest version of heating controller UNIPLEX made by Klöpper Therm again satisfies with development competence and future oriented technology in one device. Especially designed for the control and monitoring of electric heating systems, it combines several functional elements in one device. Temperature controller, safety temperature limiter and current regulator are arranged in a space saving way on a 19” plug in board in European standard size.

Condensate temperature control The Atmoset SMT regulates the residual moisture of the tissue with steam-heated cylinder dryers. The deviation of the condensate temperature from a preset setpoint is used to directly calculate the amount of energy required for drying. The heating output is optimised according to the product. The Atmoset SMT enables a stable and effective drying process. The optimal degree of drying is always reached, regardless of the weight of the product or the web speed.

Preformed silicone heaters are useful for diamters as small as 12 mm and up to 100 mm. Rounded silicone heaters are not possible with self-adhesive foil. Spiral Wrap Pre-Formed Silicone Rubber Heaters are suitable for tubes and flexible pipes and hoses with Ø 6,35 mm (1/4"). Spiral formed flex heaters can be used up to Ø 12 mm (the length of the stretchable silicone spiral wrap heater is reduced accordingly). The thickness of our spiral-wrapped silicone strip heaters is 2,2 mm. Also our gas and pump line heaters, most frequently used in the semi-conductor process, are shaped and pre-formed according to the object geometry to be heated. They are designed to regulate temperatures in order to prevent condensation in the line. Current applications here are Semi Conductors, Vacuum Chambers, Wafer Chucks, Valves, Exhaust & Pump Systems.

Freek pump and gas line heaters for trace heating are designed to regulate temperatures in order to prevent freezing or condensation in the line. As with all our heaters, these can be designed and produced to your bespoke specifications. A most frequent application for gas & pump line heaters the semi-conductor process in which gases such as Tetraethyl Orthosilicate (TEOS), Boron Trichloride (BCl3), Aluminium Chloride (AlCl3), Chlorine Triuoride (ClF3) and Dichlorosilane (DCS) condense at low temperatures. Should this occur, it could result in wafer defect. Gas and pump line heaters consistently heat the lines and provide a simple heating solution and prevent condensation build up. The optimum line temperature will vary depending on the process.

Whether for use in a workshop, in living or working spaces – the combination of a robust construction, sound workmanship and discreet design harmoniously integrates in any environment, and the thermally insulated carrying handle makes the device quick and easy to transport. The desired temperature can be regulated as needed via the integrated infinitely variable thermostat of the TDS 50 M. For more targeted warmth, the heating capacity can be increased in two stages up to 9 kW. If required, the fan can also be used in sole fan operation without heating function. The TDS 50 M is powered by three-phase current, which is, however, not supplied to a conventional heating coil but to a durable PTC ceramic heating element integrated in this electric heater. In direct comparison, this does not only entail a more homogenous hot air current and a lower noise generation – the ceramic PTC heater battery also offers many additional assets.

The semiautomatic sealing device PolySeal Vario PN is suited for the sealing of all sorts of plastic and glass containers. electro-pneumatic stepless pressure regulation sealing head heatig block, swingable, anodised aluminium hollowed out sealing die heat protection shield stabiliser roller guide with running slide container holder, adjustable container holder optional (see picture) VARIOTRONIC - regulation of temperature, sealing time and pressure The sealing device is modularly upgradeable to the PolySeal Vario Twin.

SEAMIAUTOMATIC SEALING DEVICE suitable for the sealing of all sorts of plastic and glass containers. 1. foil application device PolySeal Vario DIS (left hand side) electro-pneumatic stepless pressure regulation stepless manual height adjustment with height scale foil dispensing with 2 spot pre-sealing removable pre-sealing plates heat protection shield vacuum suction nozzle roller guide with running slide foil magazine for stackable pre-cut sealing lids VARIOTRONIC, control unit for the regulation of temperature, sealing time and pressure 2. sealing device PolySeal Vario PN (right hand side) electro-pneumatic stepless pressure regulation stepless manual height adjustment with height scale sealing head heating block, swingable, anodised aluminium hollowed out sealing die heat protection shield container holder VARIOTRONIC, control unit for the regulation of temperature, sealing time and pressure

The CS400 Kiln Shell Imaging System relies on the MP Linescanner, which provides continuous, accurate and real-time thermal images and temperature measurements for moving processes. With the ability to scan up to 1024 data points in a single scan, the MP Linescanner can provide a complete picture of even the highest speed manufacturing processes, ensuring an accurate temperature reading. Key Features: — Polar charts highlighting coating thickness and brick thickness — Envelope profiles – including alarm functionality – over the entire kiln — Built-in, on-network storage to store historical data — Free scalable AOIs (areas, line and slice) including temperature trend analysis — Virtual 3D walkthroughs across the entire kiln — 3D views available per each defined kiln zone — Easy-to-use software configurations that showcase the scanner position relative to the kiln — Flexible image sizing and configurable orientations of rotation — Fail-safe “hot spot” alarm outputs

Dedicated temperature profiling solutions for — Anti-reflection coating & Thin-film deposition — Silicon PV manufacturing: contact drying, contact firing — Lamination Benefits — Measure product temperature uniformity across the process chamber(s) — Optimize the process by reducing energy costs and/or increasing throughput — Troubleshoot the process quickly and easily — Track process stability

Water cooling unit for use with the EVO 200 WP or LITE controller and Tetrix 200 in conjunction with water-cooled welding tools.ols. — Standalone or continuous operation possible — Temperature-regulated fan control — Water flow feedback through in-built flowmeter Package includes: — Water cooling unit — Inverter / cooling unit (permanently mounted) connection cable — Fasteners for EVO series — 4 l blueCool 10i-5 coolant

TAILORED POWER COOLING LUBRICANT SYSTEM Your products are characterised by high precision and perfection? Your processes are clocked from beginning to end? Your cooling lubricant system must be perfectly tuned? Offering a flushing capacity of 300 liters a minute, automatic filtration, automated sludge discharge, user configurable pump parameters, high-pressure tool actuation, and optional medium temperature regulation, the combiloop CL5 leaves no wish unfulfilled.

Density Meter EDM 4000+ with Controller The technical specifications are in accordance or exceed the requirements by the European and American Pharmacopeia and various ASTM, ISO and DIN standards, GLP/GMP, 21 CFR part 11 User-friendly and customizable software. Up to 1000 methods can be programmed and further S + H devices connected. Customs Tariff Item : 9025 8040 HS / EU Country of Origin : Federal Republic of Germany Technical data Measuring range Density: 0 - 3 g/cm3 Temperature: 5 - 95°C (regulated Peltier thermoelement) Pressure: 0 to 10 Bar (0 to 145 psi) Density Resolution: 0.0001 g/cm3 Precision: ± 0.0001 g/cm3* Repeatability: ± 0.0001 g/cm3 Temperature Resolution: 0,01°C Precision: ± 0,05°C Repeatability: ± 0,02°C Measuring time: < 30 sec. ** Sample volume: approx. 1.5 ml Filling: By injection Bubble detection: combined visual – electronic Operation: Touchscreen, Keyboard /Mouse /Barcodereader /Remote via PC User Interface / Display: 7" color touchscreen, 800 x 48o...

Density Meter EDM 5000 with Universal-Display (L-Controller) The technical specifications are in accordance or exceed the requirements by the European and American Pharmacopeia and various ASTM, ISO and DIN standards, GLP/GMP, 21 CFR part 11 User-friendly and customizable software. Up to 1000 methods can be programmed and further S + H devices connected. Customs Tariff Item : 9025 8040 HS / EU Country of Origin : Federal Republic of Germany Technical Data Measuring range: Density: 0 - 3 g/cm3 Temperature: 0 - 95°C (regulated Peltier thermoelement) Pressure: 0 to 10 Bar (0 to 145 psi) Density Resolution: 0.00001 g/cm3 Precision: ± 0.00005 g/cm3* Repeatability: ± 0.00001 g/cm3 Temperature: Resolution: 0.001°C Precision: ± 0.03°C Repeatability: ± 0.01°C Measuring time: < 30 sec. ** Sample volume: approx. 1.5 ml Filling: By injection Bubble detection: combined visual – electronic Operation: Touchscreen, Keyboard /Mouse /Barcodereader /Remote via PC User Interface / Display: 7"...

A benefit for everybody: warm and dry shoes! Body heat air of shoe dryer with warm air blower absorbs moisture and dries them as well as comfortable warm Details of shoe dryers with hot-air blower Efficient air regulation by turning valve Very simple timer Meeting demands in various sizes and versions Reliable odor removal through ionisation (optional) Independent regulation of drying temperature Thermal protection in the blower and in the heating system (overheating is excluded) Shoe dryer with hot-air blower is available in two versions: Shoe dryer with mobile hot-air blower Technical data: Dimension in cm: 60 (W) x 90 (H) x 50 (D) Power in W: 0,5 Weight in kg: 31 4 castors (thereof 2 braked) Shoe dryer with hot-air blower mounted-wall Technical data: Dimension in cm: 60 (W) x 75 (H) x 50 (T) Power in W: 0,5 Weight in kg: 21 mounted-wall