Steel tempering - Import export

are bolts hot forged from all common materials including stainless, acid resistant and heatproof (inductive hardening, case hardening, quenched and tempered) steel. Diameter range of M 12 - M 80 with lengths reaching up to 800 mm. Tailored manufacturing according to specific standards, drawings and samples.

PT screws for thermoplastics: Thread rolling screws for direct screwing into plastics, Thread 30° or 60° KTG screws for thermoplastics: Single-start or double-start thread (high, low) Thread rolling screws are extruded for larger batch sizes and turned for small batch sizes (Turned parts for direct screwing) High tensile and highly stressable connection of thermoplastics with considerably longer life endurance Thread rolling without chips and loss of material Minimum radial tension, large thread coverage Process-reliable due to torsion strength Shorter and slimmer screws are possible. Materials: Steel, case-hardened Quenched and tempered steel 1.5523 tempered to 1000 +200 N/mm², high-grade steel 1.4567, other materials on request Length: 3 – 160 mm (at lengths from 60 mm only partial thread lengths 4 x d are possible) Thread diameter: 1.6 – 10 mm Special dimensions on request Batch sizes: Standard ex-stores Special screws from 30,000 pieces

JDN Air Hoists PROFI 3 TI up to PROFI 100 TI also available as hydraulic hoists. PROFI 3 TI JDN Air Hoists PROFI Carrying capacities: 250 kg up to 100 t Air pressure: 4 bar or 6 bar Standard Features suitable for application in hazardous areas (Explosion protection) sensitive infinitely variable speed control for the precise positioning of loads easy operation suitable for lube-free operation frequent switching and extended duty cycles low maintenance low headroom, lightweight sound absorption insensitive to dust, humidity and temperatures ranging from -20°C up to +70°C from 1 t upwards with overload protection (EC-version) Technical Details fail-safe starting conditions, low maintenance vane motor chain sprocket in the mid section runs in dust proof maintenance free ball bearings planetary gear in long life grease lubrication, all teeth made of tempered or hardened high grade steel chain and hook of high quality tempered steels with a breaking strength of five times the...

Advantages of Heating Plates with Square Cartridge Heaters: -> Simple plate manufacture due to rectangular groove geometry, no deep-hole boring -> Simple heater installation by bending and pressing along the plate surface -> Complex plate geometries with bores and openings -> Optimal heat transfer due to 75% surface contact -> No casting with heat conductive compound -> Uniform temperature profiles due to thermally optimized groove layouts/power distribution and utilization of insulation plates -> high process temperatures (up to 450°C in aluminium, up to 700°C in stainless steel) Example "Heated Stamp": D=100 mm out of tempered tool steel up to max. 700°C continuous temperature. Fitted with 2 Square Cartridge Heaters 1500 W/ 230 V, 4,5 x 4,5 mm x 600 mm, with 50 mm unheated at the termination end. Annealed and formable with a nickel sheath, resistant up to 850°C surface temperature. Connection by fibreglass insulated pure nickel high-temperature leads (max. 500°C)

This material group stands for breaking strength, service life and wear resistance. Due to these properties, quenched and tempered steel is always used where high strength, yield strength and high toughness are required for highly stressed machine parts. C 22 E, C35 E, C 45 E/➔ according to DIN EN 10132 - 3 Depending on the customer's requirements, we supply treatment states from soft annealed to high cold solidified.

We supply the European and international market with cold heading wire / cold extruding steel in sizes ranging from 1.5 mm to 42 mm Production is based at the Hamm and Iserlohn sites, focussing on the following products: Cold heading wire / cold extruding steel Tempering steel Quenched and tempered steels / AFP steels Prehardened steels

We supply the European and international market with spring steel wire for temperable springs from our Iserlohn-Kalthof plant in sizes ranging from 7.0 mm to 40.0 mm

The AL-ROCK is a laser hardening system for surface hardening with a self-propelled caterpillar track. The laser can be brought directly to the workpiece. Time-consuming removal of the components to be hardened can often be avoided. The robot arm easily reaches the hard-to-reach places on the workpiece. All common metals can be hardened, e.g. Quenched and tempered steels, cold work steels and cast steel or gray cast iron. The material must have at least 80% pearlite. The degrees of hardness that can be achieved are identical to those of conventional hardening processes. In free 3D movements, the laser beam precisely follows even the most demanding three-dimensional workpiece contours, for example on tracks along closing edges. Pimples, scar structures. Simple points are also not a problem. Only the free access of the laser beam to the surface to be hardened is required. And the AL-ROCK can do even more - on request, the laser robot can also be used for laser welding.

High feed and short machining times are the advantages of the LMT Fette MultiEdge 2Feed mini in a nutshell. High removal rates are achieved especially when machining hardened or high-tensile materials, even with large projection lengths. These results are delivered by the proven high-feed geometry of the 9 mm small indexable inserts, their positive rake angle, the new LCK10M cutting material with high carbide content and the TiAlN-based high-performance coating. The machining of high-tensile steels up to 63 HRC and chilled cast iron up to 67 HRC presents no problem. The machining time for one type of tempered steel was almost half that of a competitor tool.

• small, compact, easy to store in the drawer • fine chrome-plating • transport wheel and knife from special, tempered steel

Bush conveyor chains are often used for conveying tasksinvolving long transport distances at relatively low speeds. Since only a small minority of chains used in the industry are totally compliant with one specific standard, ELITE conveyor chains are custom-made to a specific customer order and consequently fulfil a large number of special requirements. ELITE highlights: • Pins usually made of heat-treated alloy steel, inductionhardened • Bushes made from seamless precision steel tube, case-hardened • Link plates made of high-strength tempered steel or case-hardened steel alloy • Rollers (where present) made of case-hardened steel, case-hardened