Stainless steel tubing - Import export

Guide tubes for solenoid valves, deep-drawn from stainless steel. Tightest tolerances, high quantities

Suction lances / suction tubes can be delivered in different diameters right from stock. We also can manufacture according to your drawing and/or sketch or sample. material: stainless steel AISI 304 or aluminium AlMgSi 0.5 F22 in all common tube dimension 40.0 / 50.0 and 60.3 mm right from stock special versions can be realised at short notice and for short delivery

Suction lances / suction tubes can be delivered in different diameters right from stock. We also can manufacture according to your drawing and/or sketch or sample. material: stainless steel AISI 304 or aluminium AlMgSi 0.5 F22 in all common tube dimension 40.0 / 50.0 and 60.3 mm right from stock special versions can be realised at short notice and for short delivery

Our stainless steel pipes offer the following characteristics: pipe ends deburred quantity delivered in accordance with customer’s specifications well and protective transport packed

In pneumatic conveying systems, conveying abrasive products – in particular at high conveying speeds – leads to abrasion and thus to wear in the pipe bends. In order to prevent this, the pipe bend of our highly wear-resistant DWR double-skin stainless pipe bends is encased in a second pipe bend, which creates a double-walled chamber. This acts, so to speak, as a “protective shield”: After the wear has taken place on the internal pipe bend, it fills with the product to be conveyed. When this process is completed, you are then conveying „product on product“ – and no further wear is possible! Version I: „Product-on-product” In this variant, the classic “double skin” comes into effect. not suitable for foodstuffs not suitable for material change Version II: „Lined with concrete” lined with extremely hard concrete colour: light grey not suitable for foodstuffs also available: lined with borosilicate glass

We can supply you with highly wear-resistant stainless steel pipe bends which have a service life 10 to 20 times longer than that of standard stainless steel pipe bends. This high degree of wear protection is required, for example for conveying fibreglass-reinforced plastic granules or similarly abrasive media. suitable for use of highly abrasive products easy installation no stepped pipe couplings and no flange connections required safe for use with food

Our speciality are thin-walled pipe-bends with large bending radius, especially for pneumatic conveying systems. The pipe-bends are cold-bent without any pleats on CNC-mandrel machines. Our quality management generally guarantees: welded seam smoothed or shaved (DIN 11 850 resp. DIN 17 457) absolutely wrinkle-free, no start-up bulges no scratching or scoring extremely low ovality visually aesthetic surface leg extension each side deburred sawing edges

stainless steel*finger grip*length 130 mm*up to 30 mm Ø

Universal solution when different hose diameters have to be welded together. These step connectors are mostly used for accessory exhaust systems with larger diameters.

A flexible and cost-effective way of connecting tubes to each other reliably and stably. RK Rose+Krieger developed the precision-cast stainless steel tube connectors specially for heavy loads and impact-resistance. The high-strength tube connectors are resistant to high temperatures and corrosion, and are engineered for dynamic loads. An electrochemical passivation – the tube connectors are electropolished in a final working step – makes them more resilient and resistant to acids than elements made of untreated stainless steel. As a result they are particularly resistant to cleaning with aggressive cleaning agents or hot water from high-pressure cleaners, and ideally suitable for use in packaging machines or for feeding technology in plants in the chemicals industry. Stainless steel clamp connectors are tough. Stainless steel clamps are particularly important for users working in the fields of chemical and food technology.

Tubing Stainless steel

stainless steel*for 50 test tubes

Flexible information terminal for the POS / POI consisting of a 21.5 inch multi-touch PC with Android operating system and a stand. The powerful processor enables many individual application possibilities "stand-alone" or internet-based. The stand, made of an oval silver-coloured steel plate and 2 brushed stainless steel tubes, ensures a secure stand.

We will provide you with pipe couplings for different outer tube diameters e.g. to connect glass bends with stainless steel tubes. DVK-6 pipe couplings for suction conveying can be delivered in the following sizes: 47.0 to 40.0 mm 56.0 to 50.0 mm 66.0 to 60.3 mm

Our highly flexible vacuum hoses are produced from longitudinal seam-welded, thin-walled stainless steel tubes, which are hydraulically formed in special-purpose machines. Our vacuum hoses are specifically cleaned after metal forming, during processing protected from uncleanness and prior to dispatch shrink-wrapped. Furthermore, all vacuum hoses will be leak tested prior to dispatch, by means of helium leak testing with up to 10E-8 mbar*l/s.

Screw-in heaters are versatile and intended for heating liquid media in industrial and commercial applications. When selecting, the specific surface load permitted for the respective medium must be observed and checked by the customer. EHK G2 are mainly used for heating hydraulic oil in containers in which the replacement of the heating cartridge without draining the medium must be possible. Ceramic heating cartridge in stainless steel tube ø 50mm, material-no. 1.4512 or material-no. 1.4404. G2″ thread SW70 welded from V2A. Terminal box made of PA6-GF30, impact-resistant and oil-resistant, degree of protection IP66/67. Unheated zone 50mm, surface load 1,5 W/cm², voltage 230/400 V. Special versions on request.

There are many good reasons to separate tubes chiplessly. And first of all, of course, the cleanliness. Precision and output, too, are not insignificant. Our chipless orbital cutting machines make precise cutting results possible. Your tubes can be formed immediately afterwards. That saves time and money. Technical specifications: Separation efficiency: max. Ø 28 x 2 mm for stainless steel tubes Shortest separation length: — 25 mm (without pull apart) — 55 mm (with pull apart) Separation efficiency: up to 2,000 pcs per hour

Occasionally also these terms are used for cartridge heates: heating cartridge, insertion heaters, spiral cartridge heaters. As a rule cartridge heaters consist of a cylindrical stainless steel tube and thus provide a high corrosion prevention. There is a heating wire inside which is wound onto a ceramic core. The number of coils varies depending on the power. In order to avoid a short-circuit, the cartridge heater is filled with magnesium oxide and compressed afterwards. Highly compacted they reach a surface watt density of up to 50 W/cm² and withstand highest stress. In the plastics industry cartridge heaters are used in hot runners in order to temper thermoplasts during injection moulding processes. Other areas of applications for process heat are e. g. packaging, diecasting or continuous casting in which zinc or aluminium are processed. Further applications are to be found in mechanical as well as medical and laboratory engineering.

The stainless steel probe LMK 387 was developed for level and gauge measurement in wastewater, sludge or water courses. The mechanical robustness of the front-flush ceramic diaphragm faciliates an easy disassembly and cleaning of the probe in case of service. Compared to the level probe LMK 382 the outside-diameter is only 22 mm, which allows an easy installation and backfitting in 1" tubes or in cramped fitting conditions. An IS-version is also available. Features: — nominal pressure: from 0 ... 4 mH2O up to 0 ... 100 mH2O — accuracy: 0.35 % (opt. 0.25 %) FSO — diameter 22 mm — diaphragm ceramics 99.9% Al2O3 (on request) — highly appropriated for wastewater, sludge and viscous media Optional Features: — IS-version — housing material titanium — drinking water certificate according to DVGW and KTW — temperature element Pt 100 — mounting with stainless steel tube — different kinds of cables and elastomers

When used with a commercially available vice, STAUFF manual tube benders, type TUB-MA, enable common hydraulic tubes to be bent manually. They are suitable for steel and stainless steel tubes with diameters of 6, 8, 10, 12, 14, 15, 16, 18 and 22 mm with a defined minimum wall thickness. In addition to the metric version, a model for handling imperial tubes with diameters of between 1/4 and 7/8 inches is also available. The eight bending rollers – six in the imperial version – ensure maximum wear. A scale lasered onto the bending rollers enhances the accuracy of the required bending angle with superior precision. The manual tube bender is supplied with all the necessary components and multilingual instructions for use as a complete kit in a high-quality steel case. Features and advantages Technical Data

Combination of air breather and water removal filter Features ▪ Available in 4 different sizes ▪ Diameter of Ø100 mm / Ø3.94 in or Ø130 mm / Ø5.12 in ▪ Refillable with drying agent (non-toxic ZR gel grain) or a mix of drying agent and active carbon ▪ Drying agent capable in changing colour from Red to orange with increasing moisture ▪ Without dangerous substances according to EC Council directives 99/45/EC and 2001/60/EC ▪ Replaceable air filter element SGB ▪ Connection: Male BSP thread (ISO 228) on Stainless Steel tube ▪ Available with adaptor plate to simplify installation and to enable the use of a visual contamination indicator ▪ Adaptor plate ▪ Visual contamination indicator ▪ Drying agent refilling material ▪ Active carbon refilling material ▪ Replacement air filter element

Service pressure: 0-26 Mpa Service temperature: -40°C up to 85°C Reliable in filling and operation direction Compact design Stainless steel, Aluminium HC-plated, corrosion resistant All seals are suitable for CNG EC 79 is planned The fitting is equivalent of heavy metal regulation Burst pressure: > 200 Mpa, 20° Curved stainless steel tubes from 6, 8,10mm and 3/8", ½" Tightness: 1x10-5mbar l/s, 20°C, 100% He

Service pressure: 0-26 Mpa Service temperature: -40°C up to 85°C Reliable in filling and operation direction Compact design Stainless steel, Aluminium HC-plated, corrosion resistant All seals are suitable for CNG EC 79 is planned The fitting is equivalent of heavy metal regulation Burst pressure: > 200 Mpa, 20° Curved stainless steel tubes from 6, 8,10mm and 3/8", ½" Tightness: 1x10-5mbar l/s, 20°C, 100% He

To prevent an ABS-Lock III anchorage point from being accidentally bent during the pre-tensioning process, it can be reinforced using one of our specially designed stainless steel ABS-Lock III Supporting Tubes (Ø 42 mm). Simply contact us to check whether your anchorage point can be upgraded prior to installation. Supporting tube for Ø 16 mm posts Designed for usage as a corner or end post in a lifeline system Includes an energy absorber

Reinforce your ABS Weight OnTop Double anchorage device with this optional supporting tube (Ø 42 mm) to withstand the increased tension exerted on the corner and end supports in a lifeline system. This device comes with an extra energy absorber. Supporting tube for Ø 16 mm posts Required for usage as a corner or end post in a lifeline system Includes an energy absorber