Metal perforating - Import export

Wall hanging cabinet with 1x metal door, with perforated panel in the rear and 1x shelf, WxDxH 400x300x600 mm

Plastic for welding … Welding is often the simplest and best way of fastening. The range of different perforated plates offers a wide range of applications. Size and quantity of the welding joints depend on the substructure and must be defined on site. Please note that the perforated metal sheet can under no circumstances take over any static functions. The secutex buffer pad is simply disconnected by grinding away the welding spots. These are the advantages Simply weld onto the item to be welded No need for repeatable holes in the workpiece No holes in the secutex impact protection material Applications On all metal surfaces On thin metal walls Everywhere where screwing is not possible or screw holes are unwanted Examples Collecting basins Ramp protection metal boxes Container Forklift Gripper Girder protection Pallet truck 1. Perforated metal sheet, overhang at the side This version is suitable for welding onto flat surfaces and extrawide profiles of construction steel.

Special version of the Optigreen Triangle Maxi Inspection Cham-ber TMK with perforated intermediate floor to guide excess water from higher roof areas.For feeding and conveying excess water from rooftops located higher up to floors located lower down Conveys water through downpipes directly into a tie-in conduit with an open inlet at the top, e.g. in case of: Cascading drainage from smaller top floors, feeds roof drainage water from downpipes on façades into drainage levels of underground car parks or similar Can be connected to up to 6 WLP Plus and 3 TSK With perforated sheet metal intermediate partition Walkable

Round, steel waste basket with 30 mm wide perforation ring. Capacity: 15 litres. • Round waste paper basket • Capacity: 15 litres • Made from scratch-proof, epoxy resin-coated steel • With a 30 mm wide decorative ring of perforations • Suitable for use in offices, hotels and other prestigious spaces

Metal umbrella stand with perforation. Capacity: 28.5 litres. • Metal umbrella stand with epoxy resin coating • With decorative perforated strip • Ideal for entrance areas, offices, shops or the home • Capacity: 28.5 litres

Automated punching plants are particularly economical for large quantities, offering excellent process safety. The ECKOLD range of punching machines includes automated punching units as well as portable and hand-held tools, thus catering for virtually any punching task. After a detailed evaluation of your punching task, we devise a solution that is not only economical but also perfectly adapted to match your requirements and workpiece specifications. This offer includes: • Pneumatic punching frame for fixing a cover • Stationary or robot-guided • Round hole, D = 3.5 • Integrated suction nozzle for scraps • Punching inserts • Assembly condition/interfaces: drilling pattern at c-frame • Connectable to cylinder, feed ejectors, initiators Tools are not included in the scope of delivery. They must be chosen separately, based on the actual task. Other drive types on request. Contact us for a customised offer!

for perforating thin aluminum sheets (eg heat protection sheets) and foils

The surface of the perforated metal plank, type BN-GA is a mix of closed punched nobs facing upwards and conical drain holes facing downwards. This means that the grating does not have any sharp edges on top and can be walked on easily even without footwear. At the same time, however, any liquids can be quickly drained through the conical drain holes so that no hydroplaning can occur.

With perforated metal planks, type BN-O “Noppe, offen“ the bothsided punched holes have a diameter 8 mm and allows an excellent standing stability. Furthermore the drain holes exhibit good drainage. The BN-O grating guarantees a high stability for normal pedestrian traffic.

The perforated metal planks, type BN-G “Noppe, geschlossen”, the punched nobs pressed upwards are closed and offer high slip resistance. BN-G gratings are often used in indoor environments and there, where, on the one hand, a closed surface is desired and on the other, good accessibility must be ensured.

The perforated metal planks, type BN-G33 “Noppe, geschlossen” has upwardly pressed closed nubs and provides a high slip resistance. BN-G33 is suitable for indoor in combination with BN-G33vi stairtreads. BN-G33 is suitable for areas where on the one hand a closed surface is desired and on the other hand a good accessibility must be guaranteed.

The perforated metal planks, type BN-O33 “Noppe, offen” combines top and bottom pressed nubs with a hole diameter of 8 mm: This provides excellent stability and drain holes for a good drainage effect. In combination with the profile BN-O33vi for steps with vi-nosing or the closed profile BN-G33 it results in many applications and variations.

The perforated metal plank type BZ-GP has been developed from our approved planking type BZ-GP. Because of the homogeneous surface it is easy to negotiate. Furthermore the free cross section of 70 % makes a high light permeability and sprinkler suitability possible. Therefore the profile is particularly suitable for suspended ceilings. There is no need for sprinkler systems below the suspended ceiling. Due to the high point loads, additional planking during the assembly or later is not necessary. Thus, an ideal smoke funnel, sprinkler suitability and efficiency are guaranteed.

The perforated metal plank type BN-OD „Noppe, offen , different“ is characterised by two different hole sizes. The bothsided punched holes have upwards a diameter of 14 mm and downwards a diameter of 7 mm.

The perforated metal plank type BN-OP5 “Noppe, offen plus, 5mm“ was especially developed for pedestrian areas with „High Heel Proof“ requirements. The bothsided punched holes have a diameter of 5mm. The punching sequence corresponds to BN-OP7. This type of planking offers high slip resistance and also allows ladies in stiletto heels to walk safely on the gratings. Due to the small hole configuration it is difficult to see through from underneath, which is important in public access areas. The perforated metal plank type BN-OP8, corresponds to type BN-OP5 in terms of the punching pattern, but have twice the number of holes. The drain holes have a diameter of 8 mm and thereby increase the drainage performance and light and air permeability..

The perforated metal plank BZ-Gv “Zahn, groß, verkehrt” offers a free cross section of at least 70%. It is therefore suitable for use in intermediate levels. Through the use of BZ-Gv profiles, the there is no need for a sprinkler system below these intermediate levels. Optimal flue exhaust and sprinkler suitability are thus guaranteed.

Perforated metal planks, type BP-UE are characterized by the highest slip resistance class, their smooth line profiling and high loading capacity. For this reason this type is frequently used in slippery areas and where stringent demands are made on load bearing capacity.

The perforated metal plank type BZ offers a high degree of slip resistance due to its serrated surface structure. For this reason, the BZ plank is especially suitable in those environments, where fats and oils are used.

Perforated metal planks, type BP-oN is very interesting for shelving areas, due to the smooth surface without holes or nobs. The type BP-oN is especially interesting for cantilever rackings based on its wide free span.

Perforated metal planks, type BP “parallel”, are characterised by their smooth line profiling and high loading capacity. For this reason this type is frequently used when large areas have to be covered in industrial areas and where stringent demands are made on load bearing capacity. This type can also be supplied without holes and is therefore ideal for use in the shelving construction sector.

The perforated metal plank type BR is particularly suitable for areas of heavy loads on small contact areas due to its rhomb profile with extra high punching (punched holes 2.5 mm). Here, for example, vehicle navigability on ramps or parking areas are to be considered.

CHARACTERISTICS For clamp mounting into the pipeline Efficient protection of dirt-sensitive system components during commissioning Low differential pressure Easy installation and replacement Material Certificates DIN EN 10204/3.1 for Clamp Collar OPTIONS For DIN and ASME flange connections Design for low temperature down to -50 ° C Design pressure up to 100 bar Stainless steel construction Reverse flow direction GENERAL The starting screen VAS is used for commissioning and starting a system in order to clean gas from coarse soiling such as welding bead, scale, grease, etc. After starting, the starting screen can be removed from the pipeline. The design is carried out as a welding design. FUNCTION The starting screen VAS consists of a supporting basket made of perforated sheet metal with a welded clamping ring. These are galvanized after assembly. On the outside of the support basket a stainless steel wire mesh is welded.

Reduce downtime and maintenance requirements with ROXDUR wear products. ROXDUR is a wear plate product that utilises the latest technology to provide a long lasting and durable wear solution suitable for heavy duty and medium duty applications. ROXDUR products can significantly increase the life of your fixed plant equipment. Our innovative manufacturing processes ensure a superior wear product that will save you time and money in the long run. ROXDUR wear plates are designed with the highest quality and years of expertise. Our pre-designed products can also be customised to fit your requirements. ROXDUR uses a unique composite material* that combines extreme hardness to minimise abrasive wear and iron matrix technology to absorb impact. The metallurgical bond between the cemented carbide and iron matrix gives a composite material with very high-quality adhesion to the cemented carbide. *patent pending MATERIAL CHARACTERISTICS Combining extreme hardness with shock resistance

The Modellrange ECONOMIC is made of durable sheet steel. It comes with adjustable media consumption, a blast media collection bin and a sieve to separate blast media from contaminations. The cabinet has two lateral openings with sealing sliders for rod materials. A perforated metal plate with enforcements. The system has a sectional door that opens the complete workspace. The Cabinet comes with a door-safety switch, two large operation holes with multiple rubber Sealings. Monitoring window, sized 400x500 mm, with easy changeable glass/safety-glass panes, as well as 2 durable pneumatic springs. Energy Saving Lamp, attached from outside. Injector-type blast head, with air- and blast nozzle made of hardened steel. The system comes with all necessary compressed air and blast media hoses, oil-water separator, manometer, an electrical magnet valve and a foot switch. On/Off switch, dust filter system 0,55 kW, intermediate pressure turbine. Dust collection bag.