Measuring station - Import export

The new Scout VGS 4500 measuring station consists of measuring probes mounted on the front of the vehicle and a measuring cell installed within the vehicle. These two parts are connected via a suction hose. The system can be mounted on different type of vehicles such as a pickup truck, quad or car. To adapt to nature of the surface to be measured, the probe distance can be adjusted quickly and it is just as easy to store the entire front probe. With the Scout VGS 4500 measuring station from Schütz, very large sections of network can be inspected and the results can be recorded in a short time. With the vehicle-based measuring system, measurements are accurately taken at speeds up to 50 km/h. Even under the most difficult conditions, Scout VGS 4500 has proven its reliability. The system was successfully subjected to a resistance test in the desert at an outside temperature of over 36 degrees Celsius.

Removal of determined locking ring class (double removal) with control measurement and transfer to assembly station Locking ring assembly and testing (cycle time approx. 30 sec.)

Solar power plants, wind parks and combined heat and power systems have established in energy generating technology. To achieve a high operating reliability, MicroControl solutions ensure perfect system control and precise transfer of measurement data. As for example in the adjustment of solar panels, in temperature measurement in block-type thermal power plants or in torsion measurement in wind power stations.

All NanoTest stations combines precise measurements with high speed, proven reliability and ease of use. The versatility qualifies the stations not only for high volume quality assurance, but also for demanding development applications. This qualification helps to differentiate well-working devices from the ones with mediocre performance. In this way, unnecessary processing of low-quality devices is avoided early and possible problems during wafer production will be determined. NanoTest-W characterizes the optical and electrical behavior of VCSEL or Silicon Photonics chips on wafer level, while NanoTest-C is used for laser diodes, receivers and passive devices on bar or chip level.

The CoMeT system is used to measure the screening effectiveness (transfer impedance, screening attenuation and coupling attenuation) of coaxial and symmetrical cables, connectors, bushings, distribution components, etc. The original CoMeT (Coupling Measuring Tube) has grown into a complete system. In principle, a cable measuring station consists of the following basic components: In addition to differently dimensioned round tube systems for cables and connectors, there are also so-called “triaxial cells” that provide a larger measuring chamber volume for parts that do not fit into one of the tubes due to their geometry (sockets, distributors, etc.).

Digital readouts from HEIDENHAIN are used in a wide variety of applications. They are deployed on machine tools, infeed axes on saws and presses, measuring and inspection equipment, dividing apparatuses, setting tools, production inspection measuring stations, and more. To meet such demands, these digital readouts can also be used in combination with numerous encoders from HEIDENHAIN. Digital readouts with multiple axes are primarily used on manually operated machine tools, where their practical cycles provide optimal support to the operator during milling, drilling, or turning. By instantly displaying the position in an easy-to-read manner, digital readouts enable a significant increase in productivity.

Digital readouts from HEIDENHAIN are used in a wide variety of applications. They are deployed on machine tools, infeed axes on saws and presses, measuring and inspection equipment, dividing apparatuses, setting tools, production inspection measuring stations, and more. To meet such demands, these digital readouts can also be used in combination with numerous encoders from HEIDENHAIN. Digital readouts with multiple axes are primarily used on manually operated machine tools, where their practical cycles provide optimal support to the operator during milling, drilling, or turning. By instantly displaying the position in an easy-to-read manner, digital readouts enable a significant increase in productivity.

ZwickRoell`s HDT/ Vicat all round instruments have been designed in a manner that enables them to be convenient for testing in research and development, inwards checks of goods, monitoring of production and also in education and training. Versions with up to 6 testing stations can be made available. The instruments include measuring stations which can be lowered in an automatic manner and then there is the optional test-weight lowering. The optional re-cooling device is able to reduce the oil re-cooling time as a result of which high test-rates are a possibility. The advantages included here are that the tests possible to the standards of ISO 306, ASTM D 1525, ISO 75 and ASTM D 648. Key Advantages and Features: - Measuring station lowered automatically - Optionally available automatic test-weight lowering - Optional internal re-cooling device for rapid attainment of starting temperature - Testing to ISO 306, ASTM D1525, ISO 75 and ASTM D648.

ACANTO Highlights: - Absolute measuring method - Protection up to IP67 - Online diagnostics - Serial data transmission with CRC Absolute measuring method - Position value is available immediately after switch-on - No counting errors - No reference runs necessary, because the measured value is always available Compact design - Station width of 15 mm EnDat 2.2 interface - Additional data on the status of the length gauge is available (diagnostics, warnings, alarms) - Serial data transmission with CRC Length gauges from HEIDENHAIN provide high accuracy over the entire measuring range, are mechanically robust, and can be used in a great variety of applications. They can be deployed in a wide range of applications: They are well-suited for production metrology, multipoint inspection stations, measuring equipment monitoring, and for use as position measuring devices.

CERTO Highlights: - High degree of protection - Compact design - Ball-bearing guide High degree of protection - Protection up to IP67 Compact design - Station width of 13 mm Ball-bearing guide - Ball-bearing guide with low friction - High-precision measuring loop - Rugged design Length gauges from HEIDENHAIN provide high accuracy over the entire measuring range, are mechanically robust, and can be used in a great variety of applications. They can be deployed in a wide range of applications: They are well-suited for production metrology, multipoint inspection stations, measuring equipment monitoring, and for use as position measuring devices.

The EIB 700 evaluation electronics feature connections for four axes. They are ideal for precise position measurement in particular for inspection stations and multipoint inspection apparatuses as well as for mobile data acquisition, such as in machine calibration. The EIB 700 series are ideal for applications requiring high-resolution encoder signals and fast measured-value acquisition. Ethernet transmission also enables you to use switches or hubs for connecting more than one EIB. It is also possible to use WLAN transmission, for example.

METRO highlights: - High accuracy - High repeatability - Various gauging force variants - Long measuring ranges of up to 100 mm High accuracy - System accuracy of ±0.2 µm High repeatability - Repeatability is typically < 0.03 µm for a measuring range of 12 mm ZERODUR scale - Scale expansion is close to 0 ppm/K at between 0 °C and 50 °C Actuation by cable-type lifter - Defined velocity of the plunger - No counting errors - Precision mechanics - Ball-bearing guide with low friction - High-precision measuring loop Length gauges from HEIDENHAIN provide high accuracy over the entire measuring range, are mechanically robust, and can be used in a great variety of applications. They can be deployed in a wide range of applications: They are well-suited for production metrology, multipoint inspection stations, measuring equipment monitoring, and for use as position measuring devices.

Angled Plastic Adapter RSMP15 with 12.7 mm mini prism RSMP15 with 12.7 mm mini prism sticks quickly and easily even to difficult surfaces, e.g. glass and marble façades, historic buildings, steel girders, rails, gas and oil pipelines, etc. When using robotic total stations: permanent settling measurements can be carried out during the building work settling measurements are possible on railway tracks while under the load of rail traffic bridges and other structures can be monitored even more quickly and precisely PLEASE NOTE: At BAUTEC in Berlin, we will be presenting a new prototype with a 180° pivotable mini prism that is close-to-production. Come and visit us in Berlin in hall 21.A / 117. We look forward to seeing you!

Mini prisms RSMP190 and RSMP290 rotatable and swivellable through 360° with prisms in 12.7 and 17.5 mm RSMP190 and RSMP290 sticks quickly and easily even to difficult surfaces, e.g. glass and marble façades, historic buildings, gas and oil pipelines, etc. or can be attached using plugs and screws. For easy installation on steel structures, a magnetic version of the base plates is also available. The following accessories are available for this product (see right): Resumption points (item RSFP-X90) Magnetic or non-magnetic protective cap (RSPC10 and RSPC10M) When using tachymeters and robotic total stations the prism can always be aligned accurately with the measuring instrument the prism can be turned in a radius of 360°, making it possible to use the same survey point from different directions bridges, façades and many other structures can be monitored even more quickly and precisely When using robotic total stations permanent settlement measurements can be carried out during cons

Twistable Mini-prism RSMP180 and RSMP280 Twistable, Extensible, Plastic Housing System With 12.7 and 17.5 mm Prisms RSMP180 sticks quickly and easily even to difficult surfaces, e.g. glass and marble façades, historic buildings, steel girders, rails, gas and oil pipelines, etc. or can be attached using plugs and screws. When using tachymeters and robotic total stations the prism can always be aligned accurately with the measuring instrument the prism can be turned in a radius of 180° making it possible to use the same survey point from different directions bridges, façades and many other structures can be monitored even more quickly and precisely several prisms can be combined with each other due to the integrated connector system, making it possible to survey from different directions without having to turn the prism – see examples When using robotic total stations permanent settling measurements can be carried out during the building work settling measurements are possible on ra