Interface - Import export

The probe's measurement data can be sent to a PLC via Ethernet, EtherNet/IP, PROFINET or EtherCAT fieldbus Fieldbus compatible interface module: MG80-NE (Ethernet) / MG80-EI (EtherNet/IP) / MG80-PN (PROFINET) / MG80-EC (EtherCAT) Up to 16 MG80-CM counter modules for measuring probes can be connected to each main module. Up to 64 MG80-CM or touch probes can be connected to MG80-NE via max. 3 LINK connections Up to 255 MG80-CM or measuring probes can be connected to MG80-EI/PN via LINK connections. Theoretically, up to 65,535 MG80-CM or mestasters can be connected to MG80-EC via LINK connections. MG80-CM Counter module for connection of one DK or DT series probe (with MT13) Easy installation on DIN mounting rail LZ80-K1/K2 I/O module for MG80-EI, MG80-PN and MG80-EC Equipped with 8 inputs and 8 outputs

High-resolution encoder MSA213C for drive technology The requirements for sensors used for position detection in automation and drive technology increase with the complexity and performance of the associated machines and systems. A new MSA213C high-resolution absolute sensor from SIKO is a perfect solution. It not only supplies the absolute position at any time without referencing and without requiring a backup battery, but thanks to its small design and many different interfaces, it can also be integrated into the system and control environment with very little effort.

In the field there is a frequent need to measure sensor readings rapidly and easily right at the sensor and to transfer them directly to a PC without additional amplifiers or converters. The 9206 USB sensor interface can satisfy this requirement admirably, thanks to its „plug & measure“ design. The USB connection means installation could not be simpler. Typical applications: —Mobile test measurements via laptop —Laboratory test set-ups —Instrumentation and control —Diagnostic measurements in the chemical industry —PC-based recording of expansion figures in bio engineering The USB sensor interface takes its supply from the connected PC via the USB port, and uses it to generate the power supply for the sensors. The initial settings and sensor settings are made by burster in-house and saved in the USB sensor interface. These can then be fine-tuned by the customer.

The IMX12-CCM (Cabinet Condition Monitoring) can be installed in virtually any cabinet or any protective enclosure to ontinuously check the current protection degree there - even retrospectively. The DIN rail device notifies with a switching signal improperly closed doors, as well as exceedances of temperature and interior humidity, to the control system.

We offer the matching accessories for quick mounting, simple parameterization and safe protection of interface modules. From cage clamps, programming adapters and power buses up to the IP67 rated housings: Each item is perfectly tailored to the interface module series IM, IME and IMC, making installation and commissioning of your application easy.

Our wireless SureCross system enables simple and fast transmission of process data from the field to higher level control systems. In both versions, DX70 for simple cable replacement as well as in DX80 for a complex network, gateways communicate through radio signals with the nodes in the field and transfer the signals of the field devices to the controller.

The modules of the IMSP series are connected before the interface devices and provide reliable protection against voltage surges. The only 6.2 mm wide DIN rail devices are IP20 rated and can be used in the Ex and non-Ex area. Among other things, modules are available for surge-protected connection of analog signals (e.g. for analog signal isolators and temperature measuring amplifiers) as well as for connecting binary signals from switches or inductive and capacitive sensors.

We offer the appropriate interface device for separating, forming, processing, converting and conditioning analog signals. The product portfolio comprises analog signal isolators, isolating transducers, temperature measuring amplifiers, potentiometer amplifiers, trip amplifiers and level monitors - for simple and complex requirements, for Ex- and non-Ex applications, available in the IP20 housing for DIN rail as well as in the compact IP67 housing for decentralized on-site remote control.

Everywhere, where digital signals must be electrically separated and processed or current and voltage limited power supply is needed, our interface devices are used such as isolating switching amplifiers, solenoid drivers, relay couplers and rotation speed monitors. The interface devices are available in the IP20 modular housing for DIN rail as well as in the compact IP67 housing for decentralized remote-site use. The product portfolio also comprises solutions for the Ex area and SIL-certified devices.

The BL ident® interfaces are obtainable as a set together with the gateway and one to four RFID modules in IP20 or IP67. Also available are interfaces for connection to PROFIBUS-DP, EtherNet/IP™, Modbus TCP, DeviceNet™, PROFINET, CANopen und EtherCAT®. A maximum of 16 parallel operating channels are possible. Programmable gateways enable distributed and fast signal processing. Alternatively, the BL compact series offers customized interfaces in the form of compact, fully potted IP67 components.

The sliding gate control valve Type 8020 in reinforced GS3 with NAMUR interface for universal positioner assembly is suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. are easy to handle. For high speed and cycling applications this valve is the clear choice. Pneumatic Electropneumatic Digital Without positioner for on/off operation Metal bellows Limit switch Position feedback Manual override Pilot valve . . .

The sliding gate control valve type 8020 with NAMUR interface for universal positioner assembly is suitable for a wide range of process applications. Media such as steam, liquids, gases, etc. are easy to handle. For high speed and cycling applications this valve is the clear choice. Pneumatic Electropneumatic Digital Without positioner for on/off operation Metal bellows Limit switch Position feedback Manual override Pilot valve . . .

LT80 multifunction display with interface modules and clearly structured user interface Connection of up to 32 DK or DT probes (DT probes with MT adapter) Easy installation on DIN mounting rail High speed trigger module When connecting an encoder with TTL output pulses to the trigger module, measured values from up to 16 probes can be read out synchronously in dynamic applications The synchronous measurement data can be stored on the LT80 between LT80-NE Display 7-inch touchscreen LCD display for 2 to 16 measurement channels Different measurement modes and measurement functions selectable: Current value, MAX, MIN, P-P, ADD/SUB function, 2 or 4 step comparator function for automated measuring and sorting Display I/O status 3 different interfaces (USB stick, SD card, LAN) for data storage, data transfer and parameterization Different menu languages selectable (English, German, Japanese)

The capaNCDT DT61x0/IP is an industrial-grade, capacitive sensor system for displacement, distance and position measurements. Consisting of a sensor, a sensor cable and a controller, the measuring system is ready for use without any on-site calibration. Due to its very good temperature stability, immunity to magnetic fields and robust design that is protected to IP68, the capaNCDT DT61x0/IP is used for industrial measurement tasks such as air gap measurement in generators and regulation of plant and machinery.

The MDS-40-LP sensors are specially designed for large volume production from 2,000 pieces or more. As these sensors are reduced to pure measurement technology, the creation of cost-effective PCB sensors was possible. Their flat design and flexible arrangement of the magnets allows easy integration in restricted spaces. Measured values are output via a rectangular signal, which is easily evaluated via, for example, digital inputs from micro-controllers.

Micro-Epsilon offers a comprehensive range of capacitive displacement sensors. These capacitive sensors are used for displacement, position and also for thickness measurements. Different sensor designs enable optimal integration into machines and systems. The capaNCDT sensors achieve best values in terms of linearity, temperature stability and resolution. While sub-micrometer precision is reached in industrial environments, even sub-nanometer accuracy can be achieved in clean environments.

RetailConnect - the universal tool for data conversion from any source. Irrespective of device and version the integrated communication driver ensures smooth transmission. Flexible, robust and unique as regards the integration. RetailConnect allows communication between host systems and terminal equipment. Bidirectional transfer of master data and transactions (recordings and sales) is possible via RetailConnect. Transfers can be started time-controlled or via trigger file. RetailConnect is run capable as a service or manually as command line program.

This USB interface PCB enables you to connect easily the infrared temperature measuring device of the DM301 series to the PC.

This USB interface PCB enables you to connect easily the infrared temperature measuring device DM series (without DM301) to the PC.

The interface and signal processing units extend the field of application of Micro-Epsilon sensors. The interface modules are used to convert sensor signals into digital or bus-compatible interfaces. This enables interfaces such as USB, RS422, Ethernet/IP, Profinet and EtherCAT for numerous sensors. The signal processing units are also used to record several sensor signals, to calculate and output them together. This is necessary, for example, for planarity measurement or thickness measurement.

We are your reliable partner for the realisation of your products - from the initial idea to series production and beyond. Our goal is to offer you a comprehensive full service and to manufacture your products economically and in the highest quality. We support you in the consultative development of your early concepts and prepare an initial cost estimate in the concept phase. In addition, we accompany you during series and mass production with our long-standing manufacturing partners in the Far East and ensure reliable logistical handling.

Bus-compatible position indicator with two-row LCD display for indicating target and actual values. With  additional status LED for clear indication of the positioning status. Serves for monitored format adjustment aiming at reducing setup times and increasing machine efficiency. Electronic position indicator with plug connection for magnetic sensor. Optimally readable backlit display. Two-line LCD for target and actual values. Reset, incremental measurement, offset via keyboard. Integrated RS485 interface, CAN bus as an option. Display accuracy up to 0.01 mm. Absolute function via internal backup. User guidance via bicolor status LEDs. IP53 type of protection, IP65 as an option.

The IC2001/USB single-channel converter cable is used for the USB connection of optical sensors equipped with an RS422 interface. The cable is easy to install and can therefore be used in machines and facilities.

This relay interface PCB enables you to extend easily the infrared temperature measuring device DM21 D and DM201 D by two potential-free relays.

The TLOG is an efficient measurement and indication system for a maximum of 20 temperature channels with USB interface.

The TLOG is an efficient measurement and indication system for a maximum of 20 temperature channels with USB interface.

The 9206 USB sensor interface series is ideally suited to Notebook-based mobile use for high-precision, traceable calibration jobs that must be performed on-site for equipment such as presses, torque measurement facilities and pressure control systems. A factory calibration certificate or German-accredited DAkkS calibration certificate can optionally be provided for the USB interface plus relevant sensors, ensuring compliance even with the stringent traceability requirements of quality assurance standards. Specific characteristics: —Cost effective "Plug&Measure" concept —24-bit resolution —Practical and convenient DigiCal calibration and data acquisition software —Pt100 as option —Free LabView driver DLL for integrating in your own software environment —Multipurpose reference measurement chain with optional factory calibration certificate or Germanaccredited DAkkS calibration certificate —6-wire connection technology

The IF2035 interface modules are designed for easy connection of Micro-Epsilon sensors to Industrial Ethernet controllers, e.g., plant control systems. The PROFINET and EthernetIP modules are compatible with sensors that output data via an RS422 or RS485 interface. These modules operate on the sensor side with up to 4 MBaud and have two network connections for different network topologies. Installation in switching cabinets is via a DIN rail.