Holed bearings - Import export

iglidur® clip bearing, metric d1 [mm]: iglidur® clip bearing, inch d1 [inch]: iglidur® clip bearings are especially intended for the shaft bushing through plates. For this reason the bearing has a flange on each of the two front sides. After the clip-on the bearings are secured on both sides in the plate. The clip bearings have chamfered slot on the side that enables the mounting of the bearing on one side. After the mounting the bearing straddles and lines the bore in the plate. The shaft prevents the clip bearing from slipping out of the bore. The bearing cannot slip out of the bore even in axial movements. Extremely simple mounting through lateral slot Maintenance-free and self-lubricating Good flexibility in punch hole Good abrasion resistance Quiet operation Suitable for rotary and linear movements Extendibility through the slot Undetachable through double flange Special dimensions possible Plate thicknesses from 3 mm to 4 mm available from stock Material: iglidur® M250 Special properties of the iglidur® clip bearings iglidur® clip bearings are made from the most abrasion-resistant material, iglidur® M250. iglidur® M250 is a bearing material for rugged, wear-resistant bearing systems for medium loads. The bearings are self-lubricating and can be used dry. If required the bearings can also be lubricated. The material iglidur® M250 is resistant to all common lubricants. The iglidur® clip bearings are the ideal solution for bearing functions with low loads. The easy mounting makes it ideal for applications with difficult bearing locations. Compressive strength The permitted static surface pressure of iglidur® M250 amounts to 20 MPa at room temperature. Due to the good adaptability to uneven surfaces of the bearing housing, a high pressure load capacity of the clip bearings persists even in punched holes. For the most small bearing surfaces, the good vibration dampening properties and the insensitivity to misalignment are of primary importance. Surface speeds Clip bearings are particularly wear resistant in slow rotating, oscillating and axial motions. You can find the maximum gliding speeds for the various motions for the iglidur® M250 material under the materials data link shown below. A lubrication at installation or continuous lubrication raises the permitted surface speeds. Clip bearings are available from stock in dimensions of 3 to 25 mm. Fixation Triflex RS For mounting, the bearings are laterally pressed together with the large flange. The chamfered slot makes the bearing spiral-shaped, whereby it can be easily inserted in the plate. The remaining slot in the attached clip bearing can compensate for linear expansions of the circumference. Thus narrow bearing clearances are possible with clip bearings. The bearing clearance is dimensioned in such a way that in a housing bore with a nominal diameter, a shaft made with the same nominal diameter turns easily. The clip bearing can be used in H-tolerance housings up to H13. The turning of the clip bearing in the bore is also permitted. Operating temperatures The wear resistance of the iglidur® clip bearings are excellent with operating temperatures till 80°C. Even at low temperature the bearings remain elastic and abrasion resistant. When to use it? When a sheet metal feedthrough is required When the bearing should be captively clipped on in a drill hole with rough tolerance For rotating, linear and pivoting movements When a quick-mounting bearing solution is sought Clip bearings application examples When not to use it? When constant temperatures of more than +80°C occur iglidur® G When a high-precision bearing is needed iglidur® J When the housing bore is more than 4 mm long iglidur® Clips 2 iglidur® MKM When very high surface pressures occur iglidur® G iglidur® clip bearing, metric d1 [mm]: iglidur® clip bearing, inch d1 [inch]:

igubal® flange bearing EFOM With 2 mounting holes igubal® flange bearing EFOM igubal® flange bearing EFSM With 4 mounting holes, dimensional series E igubal® flange bearing EFSM igubal® flange bearing KFSM-GT With 4 mounting holes, dimensional series K igubal® flange bearing KFSM-GT igubal® flange bearing EFOM HT Applicable up to 200°C,resistant to chemicals , with 2 mounting holes igubal® flange bearing EFOM HT igubal® flange bearing EFSM HT Applicable up to 200°C,resistant to chemicals , with 4 mounting holes igubal® flange bearing EFSM HT igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins - male threads for direct connections igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins, female thread igubal® flange bearing with ball pins, female threads for direct connections igubal® flange bearing with ball pins, female thread igubal® flange bearings were developed for the bearing of shaft extensions or shaft bushings. Like all igubal® products, they consist of an igumid G housing and an iglidur® W300 spherical ball. igubal® flange bearings correspond to the dimensional series E and are offered with 2 or 4 mounting holes. Features igubal® flange bearings were developed for the bearing of shaft ends or shaft bushings. Like all igubal® products, it consists of a housing made of igumid G and a spherical ball in iglidur® W300. igubal® flange bearings correspond to the dimensional series E and are offered with 2 or 4 mounting holes. Application area As the igubal® flange bearings are also suitable for dry operation, they are particularly considered for applications in which the installation site is difficult, in humid or wet environment, or with special demands on hygiene. Thus the igubal® flange bearings are used for instance in wash-brush controls, in facade sunscreen systems, in materials handling systems and in bakery equipment. igubal® flange bearing - Applications Installation According to type, igubal® flange bearing are designed for mounting with 2 or 4 holes. The 2-hole types are provided with oblong holes that enable a trouble-free readjustment. A precise alignment of the bearing housing is not required as the flange bearing automatically compensates for error. Delivery program For shafts, igubal® flange bearings with 2 and 4 mounting holes are available in standard dimensions of 5 to 50 mm. For delivery times and more dimensions, you may please contact us. When to use it? When chemical resistance is required When a low-cost alternative is desired When dirt-resistant bearings are needed When misalignments should be compensated When fully split components are needed When not to use? When temperatures above +200°C prevail When an integrated collar is required When dimensions over 50 mm are needed When rotation speeds in excess of 0.5 m/s should be implemented igubal® flange bearing EFOM With 2 mounting holes igubal® flange bearing EFOM igubal® flange bearing EFSM With 4 mounting holes, dimensional series E igubal® flange bearing EFSM igubal® flange bearing KFSM-GT With 4 mounting holes, dimensional series K igubal® flange bearing KFSM-GT igubal® flange bearing EFOM HT Applicable up to 200°C,resistant to chemicals , with 2 mounting holes igubal® flange bearing EFOM HT igubal® flange bearing EFSM HT Applicable up to 200°C,resistant to chemicals , with 4 mounting holes igubal® flange bearing EFSM HT igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins - male threads for direct connections igubal® flange bearing with ball pins, male thread igubal® flange bearing with ball pins, female thread igubal® flange bearing with ball pins, female threads for direct connections igubal® flange bearing with ball pins, female thread

Wrapped bronze sliding bearing with lubrication holes/ CuSn8P (DIN 17662) | Low-maintenance | DIN 1494 / ISO 3547 BRO-MET®/L is a low-maintenance bronze plain bearing. However, initial lubrication is required—both oil and grease lubrication are possible. The hole depots reduce the relubrication intervals even more! High load capacity and strength with low wear, suitable for rough operation, corrosion resistant. High load capacity and stability at low abrasion. Because of perforations lubrication clearances are reduced to a minimum! For technical details, please visit the product page on our website!

Features – DC permanent magnet motor – Graphit-copper brushes – Motor housing zinc plated and chromized – Ball bearings – Mounting holes to DIN standard 42016 General data – Nominal life 3000 h – Permissible shaft loads (axial): 40 N – Permissible shaft loads (radial): 100 N – Insulations class: DIN VDE 0530, E – Protectin class: DIN VDE 0530, IP 40 – RFI suppression: feasible

Features – DC permanent magnet motor – Graphit-copper brushes – Motor housing zinc plated and chromized – Ball bearings – Mounting holes to DIN standard 42016 General data – Nominal life 3000 h – Permissible shaft loads (axial): 180 N – Permissible shaft loads (radial): 350 N – Insulations class: DIN VDE 0530, E – Protectin class: DIN VDE 0530, IP 40 – RFI suppression: 2 x L(3 µH)

Features – DC permanent magnet motor – Graphit-copper brushes – Motor housing zinc plated – Ball bearings – Mounting holes to DIN standard 42016 General data – Nominal life 3000 h – Permissible shaft loads (axial): 40 N – Permissible shaft loads (radial): 100 N – Insulations class: DIN VDE 0530, E – Protectin class: DIN VDE 0530, IP 40 – RFI suppression: feasible

Features – DC permanent magnet motor – Graphit-copper brushes – Motor housing zinc plated and chromized – Ball bearings – Mounting holes to DIN standard 42016 General data – Nominal life 3000 h – Permissible shaft loads (axial): 110 N – Permissible shaft loads (radial): 300 N – Insulations class: DIN VDE 0530, E – Protectin class: DIN VDE 0530, IP 40 – RFI suppression: feasible

Features – DC permanent magnet motor – Graphit-copper brushes – Motor housing zinc plated – Ball bearings – Mounting holes to DIN standard 42016 General data – Nominal life 3000 h – Permissible shaft loads (axial): 30 N – Permissible shaft loads (radial): 80 N – Insulations class: DIN VDE 0530, E – Protectin class: DIN VDE 0530, IP 40 – RFI suppression: 2 x L (3,9 µH)

Features – DC permanent magnet motor – Graphit-copper brushes – Motor housing zinc plated and chromized – Ball bearings – Mounting holes to DIN standard 42016 General data – Nominal life 3000 h – Permissible shaft loads (axial): 40 N – Permissible shaft loads (radial): 100 N – Insulations class: DIN VDE 0530, E – Protectin class: DIN VDE 0530, IP 40 – RFI suppression: feasible

Up to 60 rivets per minute! – Endorsed by major customers! GESIPA® speed rivets are a cost-effective alternative to automation. Speed rivet technology is a joining method that requires access from only one side and which enables fast cycle times thanks to the preloaded rivets and automatic feed. Advantages • Large grip range • Reduced variation • Optimum hole filling capabilities and bearing stress • Ideally suited for transferring shear strengths with moderate clamping force • Ideal for: — LED light strips — Electronic/pcb assembly — Lightweight sheet metal structures — PC housings — Rating plates — Blind holes

This reinforced, stainless steel anchorage point (Ø 16 mm) comes with a special supporting tube (Ø 42 mm) and includes an angular plate for lateral installation. Simply drill 2 holes through a load-bearing beam to install it. Our standard package includes threaded bolts and nuts for countering. EN 795:2012, A + CEN/TS 16415:2013 Angular plate for lateral installation Designed for load-bearing wooden structures Minimum beam dimensions: 100 mm x 200 mm Incl. stainless steel installation set

Right-hand cutting shell reamer with expanding blades. Due to the unique Hunger relief grinding operation the blades have a progressively increasing clearance angle giving a soft cutting action. The reamer fits on a tool bar and may be positioned along the tool bar at any desired position. The reamer is automatically locked in place on the tool bar by an expanding spring coupling as soon as the reamer blades are brought into engagement with the bore. Expanding tool bar guides and supporting fixtures for the tool bar are available to ensure excact alignment of the tool bar when reaming a series of aligned holes. The adjusting nut is marked with annular scale. One graduation of the scale corresponds to a change of the reamer diameter by 0,02 mm. The reamers are available with standard blades made of high quality special steel to ensure superior cutting performance. The reamers are also available with hard chromium coated blades.