Gas protection - Import export

To better protect the sensor head of the GasPen from dirt, this protective cap can be put on the sensor head.

ATMOSPHERIC PRESSURE, MAINTENANCE FREE AND PROTECTED AGAINST EXTERNAL EFFECTS The pressureless gas storage system of Lipp is used for the storage of gas produced on landfill sites, waste water treatment plants and also as external storage on biogas plants. The system is determined by its robust and technical advanced construction where the gas balloon is protected by a galvanized steel tank. This protects the balloon against UV light and also other external factors. The system is mostly utilized at landfill sites or WWTP to buffer the gas before its further processing. The experience gained during the past decades has improved the complete system and the single components and makes it a perfect choice for end users and general contractors.

The sliding gate motor valve type 8037 is suitable for the intended use in potentially explosive atmospheres according to Directive 94/9EG. Media such as steam, liquids, gases etc. can excellently be controlled with this motor valve, even in hazardous areas. Metal bellows Position electronics Analog stroke feedback Limit switch . . .Ex zones 1, 2, 21 and 22 Protection class I 2G Ex de (ia) IIC T6/T5 or T4 (gas version) Protection class II 2D Ex tD (iaD) A21 IP 66 T80C (dust version)

The reinforced version of the type 8037 sliding gate motor valve is suitable for use in potentially explosive atmospheres in accordance with Directive 94/9EG. Media such as steam, liquids, gases etc. can be excellently controlled with this motor valve, even in hazardous areas. Metal bellows Position electronics Analog stroke feedback Limit switch . . . Ex zones 1, 2, 21 and 22 Protection class I 2G Ex de (ia) IIC T6/T5 or T4 (gas version) Protection class II 2D Ex tD (iaD) A21 IP 66 T80C (dust version)

Suitable for neutral and aggressive liquids as well as liquids containing solids Application: Centrifugal pump for dry-well installation featuring a bearing-less cantilever design with direct-coupled IEC motor. Specially designed for plant engineering and confined spaces. The B80 HME Series can be operated beside the container in a dry-well installation. Liquid flowing up inside the shaft guide tube returns to the container via an overflow line. Pumps in dry-well installations allow an easier access to carry out maintenance and repair work. Features: Directly-coupled in bearing-less cantilever design Radial and axial fixed drive elements in two-piece bearing shell Pump housing in glass-fibre or carbon-fibre reinforced plastic (PP or PVDF) Gas seal for protecting the motor bearing Plastic-coated drive shaft Driven by IEC standardised motors Benefits: Compact dimensions Service-friendly dry-well installation Self-centring alignment in the bearing shell Vibration-free and...

A showcase in a class of its own that sets standards in quality and functionality. High-quality processed and anodised aluminium profiles or, on request, powder-coated in RAL colours. Single-pane safety glass, permanent ventilation, scratch-resistant and magnetic rear wall in aluminium silver, vandalism safety locks with patented frost protection and gas pressure springs with secure 85° open position, optional LED lighting - the TN series leaves nothing to be desired. Whether as a wall or floor model, in foyers or in front of buildings. And everything with ten years warranty!

Gas storage systems by Lipp have been successfully installed in more than 300 projects in Germany and worldwide. The gas storage capacity extends from 30 to 5,000 m³. The gas resistant PVC gas holder is protected by a galvanised steel cylinder. The self supporting roof is made of 1.4301 high grade stainless steel. The Lipp gas holder is offered as a complete system, including sensors and built in parts as well as steel construction, and can be easily integrated into an existing system. The main area of application of the Lipp gas holder is municipal waste water treatment plants and landfills which want to balance out fluctuations in gas production and at the same time need a buffer store for possible downtimes. A further gas holder may also be of interest for direct marketing of biogas, where feed in at certain times is necessary. The Lipp gas holder is especially attractive when considering the fact that electricity cannot be stored. But (bio) gas, which is used for power generation

SYSTEM SOLUTIONS FOR GAS STORAGE With the Lipp gas holder Lipp offers a tried and tested system solution which is complete in itself, for unpressurised storage of biogas, sewage gas and landfill gas. This solution is chiefly used for municipal waste water treatment plants and landfills. Due to its design, as well as high functional and operational safety, it also ensures low maintenance costs over a very long service life. This is mainly because the sensitive gas holder is protected against UV radiation and other environmental influences by a steel container manufactured with the Lipp dual seam system. Furthermore, this construction method allows an exact leak test and highly accurate metrological monitoring of the gas fill level. Both aspects are essential for safe and efficient plant operation. With certification according to § 19 WHG for Lipp GmbH and DVGW approval of the gas storage tank, further conditions are met for use in municipal waste water treatment plants.

Leak detector high detection sensitivity for pressurised piping and containers, e.g. on compressors, steel bottles, fittings, shut-off valves, breathing devices, oxyacetylene gas and inert-gas arc welding devices, Bunsen burners, valves, screw fittings of compressed-air lines etc. Suitable for compressed air, refrigerant, acetylene, butane, natural gas, carbon dioxide, gaseous oxygen, propane, town gas, nitrogen, hydrogen and, ammonia Suitable for checking the safety of systems with combustible gases and for avoiding financial losses through unrecognized leaks Advantages and benefits Frost-proof to -15°C Saves energy and warns of gas loss Contains corrosion protection inhibitors Tested by the DVGW in accordance with DIN EN 14291 Non-combustible Economical in use

When using high-performance CO2 lasers for welding applications, metal mirrors are usually preferred for beam guidance. Depending on the desired application, the configuration of the machining head is composed of modular individual components according to customer requirements. The possibilities are almost unlimited, ranging from the simplest welding head to complex 3D machining heads. The FH40/C focusing heads are used for laser power up to 5 KW and raw beam diameters up to max. 30mm, the FH60 focusing head for laser power up to 15 KW and raw beam diameters up to max. 50mm. All optical units have connections for direct water cooling, are available with different coatings and are generally available from stock. In addition to the cross-jet for the efficient reduction of splashes and smell on the mirror optics, protective gas feeds with a lateral or coaxial flow direction are also offered for targeted coverage of the welding torch.

Lipp developed a system for the non pressurised (up to max. 5 mbar) storage of dry gas which has been used for over 300 projects worldwide over the past 30 years or more. Sizes from 30 to 5000 m³ are available according to the gas yield in each case. The gas accumulator consists of two parts a bubble shaped storage balloon a steel container to protect the balloon against mechanical damage and the effects of weathering The container is produced using the tried and tested LIPP Double Seam System. The storage balloon is made of polyester fabric specially laminated with PVC on both sides for improved gas resistance and UV protection. It is suspended in the container by means of a support ring. The gas pressure is increased as required between the gas accumulator and the point of utilisation by means of compressors. This results in lower investment and maintenance costs on the one hand and an extremely reliable and virtually wear free system on the other. Consequently

Dual-stage, high-performance rotary vane pump with a pumping speed up to 22 m3/h With 3-phase motor With temperature sensor (Bimetal) for optimum motor protection Integrated gas ballast and HV safety valve For all low and medium vacuum applications Special feature, Various motor voltages for worldwide employment

New employees are first introduced to TIG welding in a basic training lasting several months. Only then are the first products manufactured for customers, whereby the following topics are handled in a multi-year development process, which includes the welding test for the tube welder CrNi relatively early: Material requisition Additional materials Gas protection Interpass temperature and welding temperature Maximum material temperature during welding Cleaning the weld seam Welding distortion Mechanical seam load

The separable plastic immersion probe LMK 858 was designed for level measurement in aggressive media, desalination plants and for use in more viscous media such as sludge. Since the area of application is often outside a building, great emphasis was placed on high surge / lightning protection. The immersion probe is based on an extremely robust and precise pressure sensor, the membrane of which consists of a high-purity ceramic. Another special feature of the LMK 858 is the separability of the probe head and cable part. Features: — nominal pressure: 0 ... 40 cmH2O up to 0 ... 100 mH2O — accuracy: 0.35 % (opt. 0.25 %) FSO — diameter 45 mm — chemical resistance — housing PP-HT — integrated lightning protection and increased overvoltage protection; 8 kA gas discharge tube (8/20 μsec); 4 kV surge l-l/l-e according to EN61000-4-5 Optional Features: — cable protection — diaphragm pure ceramic (99.9 % AI2O3)

The separable plastic probe is designed for level measurement of water, waste water as well as fuels and oils. Basic element is a piezoresistive stainless steel sensor. Since the area of application is often outside a building, great emphasis was placed on overvoltage / lightning protection. In order to facilitate stock-keeping and maintenance the transmitter head is plugged to the cable assembl with a connector and can be changed easily. Features: — nominal pressure: 0 ... 1 mH2O up to 0 ... 100 mH2O — accuracy: 0,35 % (opt. 0,25 %) FSO — diameter 35 mm — cable and sensor section separable — small thermal effect — integrated lightning protection and increased overvoltage protection; 8 kA gas discharge tube (8/20 μsec); 4 kV surge l-l/l-e according to EN61000-4-5 Optional Features: — SIL 2 (safety integrity level) according to IEC 61508 / 61511 — different cable and elastomeres — customer specific versions

The separable stainless steel probe LMK 358 has been designed for level measurement in waste water, waste and higher viscosity media. Basic element is a capacitive ceramic sensor. In order to facilitate stock-keeping and maintenance the transmitter head is plugged to the cable assembly with a connector and can be changed easily. Features: — nominal pressure: 0 ... 40 cmH2O up to 0 ... 100 mH2O — accuracy: 0.35 % (opt. 0.25 %) FSO — diameter 39.5 mm — cable and sensor section separable — especially for sewage, viscous and pasty media Optional Features: — IS-protection Ex ia = intrinsically safe for gas and dust — cable protection via corrugated pipe — diaphragm pure ceramic (99.9 % AI2O3) — different kinds of cable — different kinds of elastomeres

The detachable plastic submersible probe LMK 808 was developed for level measurement in water and wastewater. The basis of the probe is an extremely robust, almost maintenance-free capacitive ceramic sensor. For level measurement in river courses, on weir systems or in locks, great emphasis was placed on overvoltage / lightning protection. In addition, the cable can be protected against bites if necessary. The sensor head can be separated from the cable part and can therefore be replaced if necessary without time-consuming assembly work. Features: — nominal pressure: 0 ... 1 mH2O bis 0 ... 100 mH2O — accuracy: 0.35 % (opt. 0.25 %) FSO — diameter 35 mm — diaphragm ceramics Al2O3 (99.9 %) — excellent long term stability — integrated lightning protection 8 kA gas discharge tube (8/20µsec); 4 kV surge l-l/l-e according to EN61000-4-5 Optional Features: — mounting accessories — different kinds of elastomer

Flowmeters especially for gases The VA 45 variable area flowmeters were designed to measure gases. They can be used, for example, in industrial ovens, forges and furnaces, and protective gas and heating systems. The standardized device design is available with various connections that conform to standards. The glass measuring cone, protected by a metal sleeve with a viewing glass, makes it easy to read the flow directly.

Comprehensive Ex-protection for gas and dust environments PFLITSCH has many ATEX-certified cable glands for use in potentially explosive atmospheres – e.g. in the chemical, pharmaceutical and food industries, agriculture, wood processing and the metal industry. Your advantages: Areas of use G (Gas) and D (Dust) Equipment class II Explosion protection type e (increased safety) as well as d (pressure-tight encapsulation) in zones 22, 21, 2 and 1 The UNI Dicht Ex-cable gland versions in metal (brass and stainless steel) are available in sizes M10 to M80 and Pg 7 to Pg 48 as well as in plastic in sizes M16 to M50 and Pg 9 to Pg 36. blueglobe is ATEX-certified in sizes M8 to M85 in brass and stainless steel. TPE sealing inserts are used for operating temperatures between -40 °C and +115 °C, while silicone (LSR) inserts are used between -55 °C and +180 °C. The various Ex-certified EMC cable glands are particularly worthy of mention.

The pressure regulator can be tightened by hand without the need for a spanner. It reduces the stored bottle pressure from max. 200bar (on request 300bar) to an outlet pressure which is adjusted at the flowmeter. The flowmeters are used to set the required flow in l/min. Important: The pressure regulator has a constant outlet pressure of 2.5bar which is necessary to protect the gas flow sensor of the orbital unit. Versions: — Special Argon Pressure Regulator with twin flowmeter, brass — Special Pressure Regulator with twin flowmeter for H2-gases, brass — Special Argon Pressure Regulator with triple flowmeter, brass Pressure regulators with different connections and for use with other gas types or nickel-plated version available on request.

Efficient surge protection made from gas discharge tube and metal oxide varistors with thermal fuse. Protects electrical appliances against surges with a max. up to 13.500 A. Protects phase, neutral- and the protective earth. Indicator for the protective function. Max. loading of 16 A/3680 W. Childproof socket. In blister packaging. Nominal current: 16 A Colour: Silver/Black Plug-in system: DE

ERC LPG GasLube Special with the special formula is designed for the protection of valves and valve seats in LPG-powered vehicles and is suitable for all commercially available additive dosing systems. Especially the heavy stressed inlet valves are protected. THE EFFECT As a result of the lubrication qualities lacking in the fuel for LPG operation, special additives must be supplied to the combustion chamber by means of a dosing unit for the optimal lubrication and protection of the valves against severe stress during the combustion process.

ERC LPG GasLube Premium is designed for the protection of valves and valve seats in LPG-powered vehicles and is suitable for all commercially available additive dosing systems. THE EFFECT As a result of the lubrication qualities lacking in the fuel for LPG operation, special additives must be supplied to the combustion chamber by means of a dosing unit for the optimal lubrication and protection of the valves against severe stress during the combustion process. THE ADVANTAGES AT A GLANCE - Protects valves and valve seats against wear - Cleans the injectors and the fuel system - Reduces harmful emissions - Extends the engine service life - Tested by DEKRA

ERC AdBlue is used for the exhaust gas cleaning of passenger and commercial vehicles and added to the exhaust gas flow from a separate tank. The Effect With the combustion of diesel fuel, harmful nitrogen oxide (NOx) is created. It must be removed from the exhaust gas in order to protect the environment and comply with legal exhaust gas limits. The Result ERC AdBlue is a clear, non-toxic, synthetic urea solution stored in an additional tank near the diesel tank or in the boot of the passenger vehicle. It is not added to the diesel fuel. ERC AdBlue is used for the environmentally compatible exhaust gas post-treatment of diesel-powered vehicles by means of selective catalytic reduction (SCR system) and converts harmful NOx components of the exhaust gas into the harmless air components nitrogen and water. The benefits at a glance ERC AdBlue: Environmentally-friendly Removes harmful NOx from the exhaust gas Non-toxic and odourless ERC AdBlue is simply filled from the container...

Installation into pipelines as inline detonation flame arrester e. g. for the protection of ignition gas lines or measuring devices. Applicable for all materials of the explosion groups IIA1 up to IIA with a maximum experimental safe gap (MESG) > 0.9 mm. Operating from both sides, for a maximum operating pressure of 1.2 bar abs. and a maximum operating temperature of 60 °C.

VSG systems offer a poven and economic solution for the inductive melting of metals or alloys under vacuum or protective gas atmosphere and subsequent casting. Applications: The VSG furnaces can be universally employed for melting and casting under high vacuum or different gas atmospheres in the laboratory or production, e.g. alloying, degassing, purification melting, re-melting processing of noble metals highly pure, highly alloyed steel. • Processing of: ◦noble metals ◦ processing of highly pure, highly alloyed steel ◦ High temperature resistant materials on Fe- Ni- Co- basis ◦ Solar-silicon and other special material ◦ Special- / super alloys

With just a few settings the plasma cutting units of the Smart Focus series achieve excellent results in the cutting range from 1 to 100 mm. Even under challenging conditions highest cutting quality and speed are realised. Therefore we use our proven cutting technologies as for example Contour Cut for cutting mild steel. The optimised gas control units and torches protect the consumables, reduce the gas consumption and the costs per cutting metre.