Electric point - Import export

Particular Challenges of the Application: By tactile equipment, determination of the deepest point on a rough metal surface is neither simple or precise. As a consequence, often either too much material is removed, or the surface is still covered with defects which have to be eliminated by a following milling cycle. The equipment is arranged in parallel, so that the complete width of the slabs is covered. The sensors are calibrated to a common coordinate system and mounted on a movable gantry. Before measurement, the slabs are fixed in place. The scanners mounted on the gantry are guided over the measuring object, driven by an electric motor. The point cloud recorded by the four scanners is consolidated in a PC by means of the QuellTech image processing software which calculates the difference between highest and lowest point of the corresponding surface and compensates for possible inclination of the slab (detrending).

Safe upending of coils (90°) Body design in solid welding construction with reinforced base with no pit or floor anchoring needed Body made of strong steel plates Base with large integrated floor plate and attached box construction to protect drive components Tilting unit with neatly welded half shell attachments and two reinforced coil tables welded at 90 degrees to provide safe material seating Bedding via four pressureresistant and fully enclosed bearings with lifetime lubrication Tilting shaft of highquality ductile steel with fully enclosed bearings Tilting drive via threephase motor and triplex type Highstrength chain Tilting function via initiator with arbitrary adjustable tilting point Electrical conrol in switch box with leftright selector switches and estop

Safe upending (90°) and rotating (180°) of coils Body design in solid welding construction with reinforced base with no pit or floor anchoring needed Body made of strong steel plates Base with large integrated floor plate and attached box construction to protect drive components Tilting unit with neatly welded half shell attachments and two reinforced coil tables welded at 90 degrees to provide safe material seating Bedding via four pressureresistant and fully enclosed bearings with lifetime lubrication Tilting shaft of highquality ductile steel with fully enclosed bearings Tilting drive via threephase motor and triplex type highstrength chain Rotating drive via welded surfacehardened sprocket, integrated in base Tilting function via initiator with arbitrary adjustable tilting point Electrical conrol in switch box with leftright selector switches and estop

The Nomex heating band is an inexpensive solution for applications where a flexible heating element with low power (max. 1 W/cm²) and for max. temperatures of 150 °C is required. A well-established application is it's utilization as standstill heater to prevent condensation and frost damage when motors stand idle in cold environments. Standstill heaters reliably keep motors or electrical machines above the dew point and ensure safe operation even in harsh ambient conditions. The minimum width of the heating element is 12 mm with a maximum length of 1000 mm, bending radii of at least 15 mm are possible.

Proportional regulation and control of high flow rates • Frictionless movement; • High flow rates; • Small footprint and size; • Low power consumption; • Pressure-balanced; • High dynamics; This valve combines the advantages of the Spider-μProp technology with the benefits of a pressurebalanced valve. Due to its large orifice, high flow rates are possible. Furthermore, the valve is distinguished by a high reproducibility of the lift-off point. The electrical power consumption lies thereby in the lowest range of the Plate Armature Technology. The compact design of the valve provides a variety of assembly options for different areas of application.

Entire system solution from a single source: — from construction of the laser cell to integration of your chosen KEYENCE laser — self-contained and high-performance solutions for laser labeling small batches of individual parts SIM Marker Rotary equipment options: — electrical adjustment of the focal point — Side door, double-bit lock — Connection to PC via LAN or USB Customized — integrated suction (automatic activation when writing) — PC or Notebook with side table — Set up: directly on a desk or mounted onto the movable base frame — Latest three-axis laser marking systems offers a laser labeling system that can be precisely adjusted to the materials and part geometries that shall be labeled Advantages of integrated optical three-axis technology: — focal point to be freely set and is especially impressive Size of the labeling field: between 120 x 120 mm and 330 x 330 mm.