Construction machinery - Import export

In the highly innovative machinery and equipment construction area, our heating elements and equipment find mainly application in the tasks of heating, maintaining temperatures or evaporating liquid or gaseous media. The installation of our equipment can take place both in nonhazardous and hazardous areas of zones 1 and 2.

Construction machinery is exposed to extreme conditions and components have to be designed to long-term reliability. The systems have to feature a rugged design, high vibration resistance as well as dirt and water tightness. Also, the systems have to withstand low as well as high ambient temperatures.

If the length or angle to be monitored shall additionally be output as a continuous electrical signal, a mounting arrangement of a remote indicating device of the analog or digital type is optional available. They contain in a robust protective casing either a backlash compensated gear or a gear with reduced backlash for matching the input angle with the switching or transducer angle. Each cam unit contains two semicircular disks, which can be adjusted against each other by means of a screwdriver via a worm drive, the switching point position encompassing a switching angle from about 10° up to 350° at maximum, and over 360° of the cam shaft. Sets of break-before-make contacts are used, each comprising one normally-closed and one normally-open contact. For positional back-indication via coupling or gear, one or two angular position transmitters can be operated on the camshaft, optionally with analog or digital output signal.

Wind velocity indicators are used for detecting and in connection with the appropriate indicator, monitoring a maximum wind velocity. They are used mainly in safety and monitoring systems of cranes and excavators. Two models are available. One with pendulum orientation, especially suited for the attachment on jibs of mobile cranes, and a common one, pedestal mounted or mounted on a vertical post. The output signal, being proportional to the wind velocity is taken either from a built-in tachometer generator in form of a voltage or from an optoelectronic impulse transmitter with frequency-current converter in form of a current signal in two-wire technique. For applications in the temperature range down to minus 50 °C there is optionally available for both models a mounting arrangement for a temperature controlled heating device. Cross arms feed-through sleeve and crown are splash-proof, degree of protection IP 65.

Hydraulically operated control equipment are to an increasing extent controlled by electronic means nowadays. This is the application range - in consideration of the extreme conditions of use which the control transmitter ST2000 is especially designed for. Corresponding to the lever displacement, it provides a direction dependent switch and control signal output for both axes X and Y. Wear-free and non-contacting inductive linear transmitters are used as primary elements of the measuring system, with respect to mode of activation and robustness their design can be compared with that of the valve system of hydraulic control transmitters. The built-in electronic circuit provides for control purposes on its output per axis either a current or a voltage signal with switchable characteristic of the linear or the progressive type. A special design offers the option to incorporate a microprocessor for individual matching of characteristics.

For measuring linear displacements on machines and converting them into electrical signals for teletransmission purposes - linear displacement transmitters of the potentiometric, inductive, incrementally or absolutely coded type can be used, depending on their application. Potentiometric linear displacement transmitters comprise high-resolution wirewound resistance elements, capable of measuring length up to 1 m with high accuracy and a linearity of ± 0,1%. For protection against mechanical damage, plunger with sintered metal bearing and pull-back spring (optional) are encapsulated in a robust aluminum casing, degree of protection IP 65. Inductive linear displacement transmitters comprise a non-contact differential inductor system providing high linearity and resolution, capable to perform reliable measuring ranges from 0 to 0.5 mm up to 0 to 500 mm even under extremely severe environmental conditions.

Tilt angle values of a platform stand for important measuring data as a part of the safety and control system of machinery. Angular measurement is, for instance for equipment levelling, performed in such cases by means of dual axis pendulum systems. Transducers of that type contain inside a robust splash-proof aluminium case of protection degree IP 65 to IP 68 oil-damped pendulum systems, the tilt angle dependant swing of which is measured, depending on the application, either by a potentiometric, non-contact inductive or an optoelectronic angular encoder. For measurements relevant to safety, the pendulum swing per axis is detected with redundancy i.e. by means of two mechanically and electrically independent pendulum systems. The output signal, representing the tilt angles, is provided either in form of an analog resistance, current or voltage variation or as a digital signal - with interface bus - as well.

The signals representing angle and length of a telescopic crane are important measuring data. Determination of such measuring data is performed by means of tilt angle and rope length transmitters. The determination of the jib angle is performed by a magnetically damped pendulum system, the swing of which is measured with a redundant high-resolution conductive plastic potentiometer. The output signal is provided in form either of two resistance signals or via the built-in signal converter in form of two current or voltage signals. Linear measurement is performed according to the draw wire measuring principle. One makes use of a multiwire measuring cable, which is wound multilayered on a cable reel provided with a pullback spring. A mechanical spindle lead screw nut ensures, that the rope is rewound and unwound exactly layer-by-layer. The number of drum revolutions, being proportional to the measured length is determined by a redundant potentiometer system voltage or current output.

Rope Length Transmitter with high precision analog or digital encoders The determination of measuring lengths in the range of one up to several meters is preferably carried out by using well priced and easy-tomount transducers on the basis of the draw wire measuring principle. In connection with measuring problems of industrial applications e.g. on - cranes, drilling machines and excavators - pressing, punching and injection moulding machines - weirs and lock gates - multilevel shelving rack systems and theatre stages - wood- and stone-working machines and also in - instrument engineering, high-tech medical devices etc. Rope length measuring systems series SL 3000 have proven for years to be very reliable, capable of measuring lengths up to 40 m with high accuracy and reliability even in extremely dusty and moist atmospheres.

Today potentiometric Angular Position Transmitters attain a still more status with regard to the analogue measuring technique as far as high-quality measurement tasks are concerned due to the favourable value for money. Potentiometric transmitters have either a high-resolution element of conductive plastic or a high-resolution gold or constantan wire with various resistance and angle values. They are available in various sizes as single-turn or multiple-turn potentiometers or in a multiple design. For adjustment of the measuring range almost all series can be provided with short-circuiting tracks, taps and function windings. Some models are available with incorporated Signal Converter providing current or voltage outputs in configuration of 2, 3 or 4 wires. To ensure reliability in very dirty atmospheres, oil-filled potentiometers are available.

Angular Position Transducers with inductive magnetoresistive or optoelectronic measuring systems. Potentiometric transmitters have either a high-resolution element of conductive plastic or a high-resolution gold or constantan wire with various resistance and angle values. For adjustment of the measuring range almost all series can be provided with short-circuiting tracks, taps and function windings. Some models are available with incorporated Signal Converter providing current or voltage outputs in configuration of 2, 3 or 4 wires. Moreover, to provide protection for all potentiometers from mechanical damage, dusty and damp industrial atmospheres a series of casings with a degree of protection IP 40 to IP 68 is available which can be equipped with gearing and limit switches.

Hydraulically actuated controlling equipment, for example in - Construction and drilling vehicles - Cranes and excavators - Wheel loaders and lifting platforms - Railway Vehicles are controlled to an increasing degree electronically nowadays. Especially for these applications (under consideration of extreme operating conditions) our pedal actuated transmitters of series FS2000 were designed for. They contain wearless magnetic control systems in redundant version for security-relevant applications according to IEC 61508 (for example SIL2) with analogue or digital signal output.

These parts are made by aluminum,after machining by CNC milling, then process the sand blasting and anodize.

These are little screw used in construction industry,machinery parts ,and so on ...

iglidur® plate material Free design iglidur® J - the Fast-and-slow motion specialist - now available as plate material for free design. wear-resistant Lubrication-free Multi-purpose Good chemical resistance Lowest humidity absorption Application areas:Plant construction, fixtures, prototype construction, special machinery construction iglidur® plate material Free design iglidur® J - the Fast-and-slow motion specialist - now available as plate material for free design. wear-resistant Lubrication-free Multi-purpose Good chemical resistance Lowest humidity absorption Application areas:Plant construction, fixtures, prototype construction, special machinery construction General features Density 1,49 g/cm 3 Colour yellow Max. moisture absorption at 23 °C and 50 %r.h. 0,3 Wt.-% Max. water absorption 1,3 Wt.-% Mechanical properties Max. permissible static surface pressure (+20 °C) 35 MPa Shore D hardness 74 Physical and thermal properties Max. long term application temperature 90 °C Max. short term application temperature 120 °C Lower application temperature -50 °C Electrical properties Surface resistance 10 12 Ω

Other information IF -Design Award for Triflex®-Design Torsional movements possible Other information Installation instructions Joining, separating and filling of the Triflex®. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. Triflex® 332.16 Inner height hi: 16 mm Inner width Bi: 16 mm Bending radii R: 38 - 100 mm Pitch: 13.3 mm E-Chain®. 332.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm E-Chain®. 332.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm E-Chain®. 332.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm E-Chain®. 352.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 10 - 250 mm Pitch: 30 mm E-Chain®, snap-open 333.16 Inner height hi: 16 mm Inner width Bi: 16 mm Bending radii R: 38 - 100 mm Pitch: 13.3 mm E-Chain®. 333.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm E-Chain®. 333.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm E-Chain®. 333.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm E-Chain®. 353.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 10 - 250 mm Pitch: 30 mm E-Chain®, snap-open This modular, rugged joint system is suitable for: Three-axis movements for machines of any type For dirt-filled environments High tensile strength Where rectangular shapes are requested Completely closed - reliable protection against dirt and chips Combination of different bending radii and axes Connection and separation possible at any chain Flanged mounting brackets or brackets, galvanized steel Snap-open Series 352 and 353 Combination of Series 353/333 possible Typical industrial sectors and applications Machine tools Robotics Material handling system Plastics industry Construction machinery Vehicle manufacturing Medical equipment IF -Design Award for Triflex®-Design Torsional movements possible

Other information iF-Design Award for easy triflex® Design UL94-V2 classification Torsional movements possible Other information Installation instructions Join, separate and fill the easy triflex®. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. Triflex® E332.25 Inner height hi: 25 mm Inner width Bi: 25 mm Bending radii R: 48 - 200 mm Pitch: 14.5 mm e-chain® E332.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm e-chain® E332.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm e-chain®. E332.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm e-chain® E333.25 Inner height hi: 25 mm Inner width Bi: 25 mm Bending radii R: 48 - 200 mm Pitch: 14.5 mm e-chain® E333.32 Inner height hi: 32 mm Inner width Bi: 32 mm Bending radii R: 75 - 250 mm Pitch: 25 mm e-chain® E333.50 Inner height hi: 50 mm Inner width Bi: 50 mm Bending radii R: 100 - 250 mm Pitch: 30 mm e-chain®. E333.75 Inner height hi: 75 mm Inner width Bi: 75 mm Bending radii R: 140 - 300 mm Pitch: 36 mm e-chain® This modular joint system is especially suited for: Three-axis movements of machines For simple robotic applications Quick installation of cables with "easy" system Simple filling from both sides Where rectangular shapes are required Combination of different bending radii and moving directions Shortening or lengthening possible at "any point" KMA mounting brackets with integrated strain relief Typical industrial sectors and applications Machine tools Robotics Handling equipment Material handling system Plastics industry Construction machinery Vehicle manufacturing General mechanical engineering Medical Equipment Office furniture iF-Design Award for easy triflex® Design UL94-V2 classification Torsional movements possible

Overview for E2/000 advantages Other information Series EF2.21 Inner height hi: 21 mm Inner widths Bi: 25 - 50 mm bending radii R: 35 - 180 mm Pitch: 33.3 mm E-Chain®, snap-open along the outer radius Series 1500 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm E-Chain®, snap-open along the outer radius Series 1400 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm E-Chain®, snap-open along the inner radius Series 1450 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm Half energy tube, snap-open along the inner radius Series 1480 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm Full energy tube, snap-open along the inner radius Series 2500 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain®, snap-open along the outer radius Series 2400 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain®, snap-open along the inner radius Series 2450 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 100 - 250 mm Pitch: 46 mm Half energy tube, snap-open along the inner radius Series 2480 Inner height hi: 25 mm Inner widths Bi: 38 - 103 mm bending radii R: 100 - 250 mm Pitch: 46 mm Full energy tube, snap-open along the inner radius Series 2700 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 63 - 250 mm Pitch: 56 mm E-Chain®, snap-open along the outer radius Series 2600 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 63 - 250 mm Pitch: 56 mm E-Chain®, snap-open along the inner radius Series 2650 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 100 - 250 mm Pitch: 56 mm Half energy tube, snap-open along the inner radius Series 2680 Inner height hi: 35 mm Inner widths Bi: 50 - 100 mm bending radii R: 100 - 250 mm Pitch: 56 mm Full energy tube, snap-open along the inner radius Series 3500 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 75 - 300 mm Pitch: 67 mm E-Chain®, snap-open along the outer radius Series 3400 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 75 - 300 mm Pitch: 67 mm E-Chain®, snap-open along the inner radius Series 3450 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 150 - 300 mm Pitch: 67 mm Half energy tube, snap-open along the inner radius Series 3480 Inner height hi: 45 mm Inner widths Bi: 75 - 115 mm bending radii R: 150 - 300 mm Pitch: 67 mm Full energy tube, snap-open along the inner radius Series 255 Inner height hi: 24 mm Inner width Bi: 25 mm Bending radii R: 55 - 250 mm Pitch: 27.8 mm E-Chain®, snap-open along the outer radius CRC series. 255 Inner height hi: 24 mm Inner width Bi: 38-103 mm Bending radii R: 150 - 250 mm Pitch: 27.8 mm e-chain® Series CRC. 255 Assembly tool E"2/000 e-chains® - quick opening with assembly tools. Assembly tool Overview E2/000 bow chains Two-part - the E2 standard as clamp chain version Overview E2/000 bow chains ESD classification: Electrically conductive ESD/Atex versions on request IPA classification: ISO cleanroom class 3 (DIN 14644-1), at v=2 m/s, with standard material igumid G Series 2500.05.055.0 UL94 V0 classifications on request 46 dB(A) determined at the igus® laboratory, v = 1.0 m/s unsupported, e. g. Series 2600.05.075.0 iF Design Award for the E2/000 series EF2.21 Overview for E2/000 advantages Other information Series EF2.21 Inner height hi: 21 mm Inner widths Bi: 25 - 50 mm bending radii R: 35 - 180 mm Pitch: 33.3 mm E-Chain®, snap-open along the outer radius Series 1500 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm E-Chain®, snap-open along the outer radius Series 1400 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm E-Chain®, snap-open along the inner radius Series 1450 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm Half energy tube, snap-open along the inner radius Series 1480 Inner height hi: 21 mm Inner widths Bi: 15 - 125 mm bending radii R: 35 - 180 mm Pitch: 33,3 mm Full energy tube, snap-open along the inner radius Series 2500 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain®, snap-open along the outer radius Series 2400 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 55 - 250 mm Pitch: 46 mm E-Chain®, snap-open along the inner radius Series 2450 Inner height hi: 25 mm Inner widths Bi: 25 - 125 mm bending radii R: 100 - 250 mm Pitch: 46 mm Half energy tube, snap-open along the inner radius Series 2480 Inner height hi: 25 mm Inner widths Bi: 38 - 103 mm bending radii R: 100 - 250 mm Pitch: 46 mm Full energy tube, snap-open along the inner radius Series 2700 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 63 - 250 mm Pitch: 56 mm E-Chain®, snap-open along the outer radius Series 2600 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 63 - 250 mm Pitch: 56 mm E-Chain®, snap-open along the inner radius Series 2650 Inner height hi: 35 mm Inner widths Bi: 50 - 175 mm bending radii R: 100 - 250 mm Pitch: 56 mm Half energy tube, snap-open along the inner radius Series 2680 Inner height hi: 35 mm Inner widths Bi: 50 - 100 mm bending radii R: 100 - 250 mm Pitch: 56 mm Full energy tube, snap-open along the inner radius Series 3500 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 75 - 300 mm Pitch: 67 mm E-Chain®, snap-open along the outer radius Series 3400 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 75 - 300 mm Pitch: 67 mm E-Chain®, snap-open along the inner radius Series 3450 Inner height hi: 45 mm Inner widths Bi: 50 - 255 mm bending radii R: 150 - 300 mm Pitch: 67 mm Half energy tube, snap-open along the inner radius Series 3480 Inner height hi: 45 mm Inner widths Bi: 75 - 115 mm bending radii R: 150 - 300 mm Pitch: 67 mm Full energy tube, snap-open along the inner radius Series 255 Inner height hi: 24 mm Inner width Bi: 25 mm Bending radii R: 55 - 250 mm Pitch: 27.8 mm E-Chain®, snap-open along the outer radius CRC series. 255 Inner height hi: 24 mm Inner width Bi: 38-103 mm Bending radii R: 150 - 250 mm Pitch: 27.8 mm e-chain® Series CRC. 255 Assembly tool E"2/000 e-chains® - quick opening with assembly tools. Assembly tool Overview E2/000 bow chains Two-part - the E2 standard as clamp chain version Overview E2/000 bow chains IPA Classification Report IG 1303-640-1, tested 1500.050.038.0 at v = 0,5 / 1,0 / 2,0 ISO Class 2, according to DIN EN ISO 14644-1 E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Joining and separating of chain links, filling of the E-Tubes. Assembly Instructions System E2/000 Recommended installation accessories Application examples Applications in various industrial sectors and in the igus® test laboratory. System E2/000 The E2 standard Quickly opened from the right or left with a screwdriver or by hand - opening mechanism accessible from above Lightning fast installation using thumb - safe seat without additional closing mechanism The separators and interior separation sit safely, even when the E-Chain® is open Excellent mechanical stability; design and material provide long service life Typical industrial sectors and applications General construction machinery Materials handling technology Construction machinery Wood machines Machine tools Glass machines Plastic machines Long travels Semiconductor Theater and entertaining industry Vehicles And much more ESD classification: Electrically conductive ESD/Atex versions on request IPA classification: ISO cleanroom class 3 (DIN 14644-1), at v=2 m/s, with standard material igumid G Series 2500.05.055.0 UL94 V0 classifications on request 46 dB(A) determined at the igus® laboratory, v = 1.0 m/s unsupported, e. g. Series 2600.05.075.0 iF Design Award for the E2/000 series EF2.21

Other information Series 10 Inner height hi: 18 mm Inner widths Bi: 15 - 100 mm bending radii R: 28 - 180 mm Pitch: 30,5 mm E-Chain®, not-to-be-opened Series 11.031 Inner height hi: 23 mm Inner width Bi: 31 mm Bending radii R: 45 - 70 mm Pitch: 30.5 mm E-Chain®, not-to-be-opened Series 11.080 Inner height hi: 28 mm Inner width Bi: 80 mm Bending radius R: 38 mm Pitch: 30.5 mm E-Chain®, not-to-be-opened Series 11.1/11.2 Inner height hi: 41 mm Inner widths Bi: 15 - 25 mm bending radii R: 40 - 100 mm Pitch: 30,5 mm E-Chain®, not-to-be-opened Series 14 Inner height hi: 20 mm Inner widths Bi: 15 - 50 mm bending radii R: 28 - 125 mm Pitch: 30,5 mm E-Chain®, snap-open inside Series B15i Inner height hi: 17 mm Inner widths Bi: 15 - 100 mm bending radii R: 38 - 180 mm Pitch: 30,5 mm E-Chain®, snap-open inside Series B17i Inner height hi: 32 mm Inner widths Bi: 15 - 100 mm bending radii R: 48 - 125 mm Pitch: 30,5 mm E-Chain®, snap-open inside Series F17 Inner height hi: 32 mm Inner height Bi: 15 mm Bending radii R: 48 mm Pitch: 30,5 mm E-Chain®, snap-open inside Series B15 Inner height hi: 17 mm Inner widths Bi: 15 - 100 mm bending radii R: 38 - 180 mm Pitch: 30,5 mm E-Chain®, snap-open outside Series B17 Inner height hi: 32 mm Inner widths Bi: 15 - 100 mm bending radii R: 48 - 125 mm Pitch: 30,5 mm E-Chain®, snap-open outside UL94-V2 classifications Cleanroom class 1 (ISO class 3) Series 10 tested by Dryden Engineering Company, California Special version: Electrically conductive ESD/ATEX versions on request Other information Series 10 Inner height hi: 18 mm Inner widths Bi: 15 - 100 mm bending radii R: 28 - 180 mm Pitch: 30,5 mm E-Chain®, not-to-be-opened Series 11.031 Inner height hi: 23 mm Inner width Bi: 31 mm Bending radii R: 45 - 70 mm Pitch: 30.5 mm E-Chain®, not-to-be-opened Series 11.080 Inner height hi: 28 mm Inner width Bi: 80 mm Bending radius R: 38 mm Pitch: 30.5 mm E-Chain®, not-to-be-opened Series 11.1/11.2 Inner height hi: 41 mm Inner widths Bi: 15 - 25 mm bending radii R: 40 - 100 mm Pitch: 30,5 mm E-Chain®, not-to-be-opened Series 14 Inner height hi: 20 mm Inner widths Bi: 15 - 50 mm bending radii R: 28 - 125 mm Pitch: 30,5 mm E-Chain®, snap-open inside Series B15i Inner height hi: 17 mm Inner widths Bi: 15 - 100 mm bending radii R: 38 - 180 mm Pitch: 30,5 mm E-Chain®, snap-open inside Series B17i Inner height hi: 32 mm Inner widths Bi: 15 - 100 mm bending radii R: 48 - 125 mm Pitch: 30,5 mm E-Chain®, snap-open inside Series F17 Inner height hi: 32 mm Inner height Bi: 15 mm Bending radii R: 48 mm Pitch: 30,5 mm E-Chain®, snap-open inside Series B15 Inner height hi: 17 mm Inner widths Bi: 15 - 100 mm bending radii R: 38 - 180 mm Pitch: 30,5 mm E-Chain®, snap-open outside Series B17 Inner height hi: 32 mm Inner widths Bi: 15 - 100 mm bending radii R: 48 - 125 mm Pitch: 30,5 mm E-Chain®, snap-open outside E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Joining and separating of chain links Assembly Instructions Application examples Applications in various industrial sectors. E2 mini One-/Two-piece E-Chain® Small pitch for silent operation High torsion resistance Double stop system and large pins for long service life Optimized weight/stability ratio Easy to mount Manifold interior separation Typical industrial sectors and applications Construction machinery Handling systems Installation Packaging machines Textile machines Vehicle construction Wood machines Glass machines Machine construction General mechanical engineering etc. UL94-V2 classifications Cleanroom class 1 (ISO class 3) Series 10 tested by Dryden Engineering Company, California Special version: Electrically conductive ESD/ATEX versions on request

Other information Series E1.10 Inner height hi: 10 mm Inner height Bi: 13 mm Bending radii R: 18 mm Pitch: 20 mm E-Chain®, snap-open along the outer radius Series E1.17 Inner height hi: 17 mm Inner width Bi: 21 - 44 mm Bending radii R: 28 mm Pitch: 25,5 mm E-Chain®, snap-open along the outer radius E1.18 series Inner height hi: 18 mm Inner height Bi: 15 mm Bending radii R: 28 mm Pitch: 25.25 mm E-Chain®, snap-open along the outer radius Series E1.20 Inner height hi: 20 mm Inner height Bi: 15 mm Bending radii R: 28 mm Pitch: 25 mm E-Chain®, snap-open along the outer radius UL94-V2 classification Series E1.10 Inner height hi: 10 mm Inner height Bi: 13 mm Bending radii R: 18 mm Pitch: 20 mm E-Chain®, snap-open along the outer radius Series E1.17 Inner height hi: 17 mm Inner width Bi: 21 - 44 mm Bending radii R: 28 mm Pitch: 25,5 mm E-Chain®, snap-open along the outer radius E1.18 series Inner height hi: 18 mm Inner height Bi: 15 mm Bending radii R: 28 mm Pitch: 25.25 mm E-Chain®, snap-open along the outer radius Series E1.20 Inner height hi: 20 mm Inner height Bi: 15 mm Bending radii R: 28 mm Pitch: 25 mm E-Chain®, snap-open along the outer radius Other information E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Selection aids Installation instructions Shortening and lengthening of the E-Chain®. Assembly Instructions Application examples Applications in various industrial sectors and in the igus® test laboratory. E-Chain® Applications Overview E-Chain® in one band Cost-effective solution for large numbers E1: E-Chain® in one band Length of each chain band: 255 mm Can be shortened or lengthened as required through injection-molded, modular chain band Easy snap-open Mounting link for connection of several chain bands Fastening potential by the bore on the chain band Several potential materials Typical industrial sectors and applications General construction machinery Automotive sector Office technology Machine construction Electronic equipment General construction machinery etc. UL94-V2 classification

Coated track plates for use in crawler tracks for construction machinery. The extremely wear-resistant polyurethane Intec E provides the necessary mechanical properties for use in the crawler and protects the floor from the high machine weight. Up to 1.5 m length possible!

We manufacture gears, gear rings and toothed shafts for various applications in industry with a focus on mechanical engineering and heavy machinery. Our customers come from a wide range of industries: railway, wind power, marine, industrial gearboxes, oil and gas extraction, crane construction or construction machinery as well as special machines. We also supply the retrofit industry and manufacture the parts in small series or individual production. Depending on the dimension a quality of 4 can often be achieved. We examine the possibilities without obligation and without charge. Our customers include renowned and well-known companies. References to your industry on request. We manufacture according to customer drawings and have our own hardening plant. This saves time and costs during production. Cooperation exists for gas nitration and single-tooth induction hardening with experts in their field. ZWP supports you in the overhaul of plants and machines (Retrofit).

We manufacture gears, gear rings and toothed shafts for various applications in industry with a focus on mechanical engineering and heavy machinery. Our customers come from a wide range of industries: railway, wind power, marine, industrial gearboxes, oil and gas extraction, crane construction or construction machinery as well as special machines. We also supply the retrofit industry and manufacture the parts in small series or individual production. Depending on the dimension a quality of 4 can often be achieved. We examine the possibilities without obligation and without charge. Our customers include renowned and well-known companies. References to your industry on request. We manufacture according to customer drawings and have our own hardening plant. This saves time and costs during production. Cooperation exists for gas nitration and single-tooth induction hardening with experts in their field. ZWP supports you in the overhaul of plants and machines (Retrofit).

We manufacture gears, gear rings and toothed shafts for various applications in industry with a focus on mechanical engineering and heavy machinery. Our customers come from a wide range of industries: railway, wind power, marine, industrial gearboxes, oil and gas extraction, crane construction or construction machinery as well as special machines. We also supply the retrofit industry and manufacture the parts in small series or individual production. Depending on the dimension a quality of 4 can often be achieved. We examine the possibilities without obligation and without charge. Our customers include renowned and well-known companies. References to your industry on request. We manufacture according to customer drawings and have our own hardening plant. This saves time and costs during production. Cooperation exists for gas nitration and single-tooth induction hardening with experts in their field. ZWP supports you in the overhaul of plants and machines (Retrofit).

We manufacture gears, gear rings and toothed shafts for various applications in industry with a focus on mechanical engineering and heavy machinery. Our customers come from a wide range of industries: railway, wind power, marine, industrial gearboxes, oil and gas extraction, crane construction or construction machinery as well as special machines. We also supply the retrofit industry and manufacture the parts in small series or individual production. Depending on the dimension a quality of 4 can often be achieved. We examine the possibilities without obligation and without charge. Our customers include renowned and well-known companies. References to your industry on request. We manufacture according to customer drawings and have our own hardening plant. This saves time and costs during production. Cooperation exists for gas nitration and single-tooth induction hardening with experts in their field. ZWP supports you in the overhaul of plants and machines (Retrofit).

We manufacture gears, gear rings and toothed shafts for various applications in industry with a focus on mechanical engineering and heavy machinery. Our customers come from a wide range of industries: railway, wind power, marine, industrial gearboxes, oil and gas extraction, crane construction or construction machinery as well as special machines. We also supply the retrofit industry and manufacture the parts in small series or individual production. Depending on the dimension a quality of 4 can often be achieved. We examine the possibilities without obligation and without charge. Our customers include renowned and well-known companies. References to your industry on request. We manufacture according to customer drawings and have our own hardening plant. This saves time and costs during production. Cooperation exists for gas nitration and single-tooth induction hardening with experts in their field. ZWP supports you in the overhaul of plants and machines (Retrofit).

We manufacture gears, gear rings and toothed shafts for various applications in industry with a focus on mechanical engineering and heavy machinery. Our customers come from a wide range of industries: railway, wind power, marine, industrial gearboxes, oil and gas extraction, crane construction or construction machinery as well as special machines. We also supply the retrofit industry and manufacture the parts in small series or individual production. Depending on the dimension a quality of 4 can often be achieved. We examine the possibilities without obligation and without charge. Our customers include renowned and well-known companies. References to your industry on request. We manufacture according to customer drawings and have our own hardening plant. This saves time and costs during production. Cooperation exists for gas nitration and single-tooth induction hardening with experts in their field. ZWP supports you in the overhaul of plants and machines (Retrofit).

We manufacture gears, gear rings and toothed shafts for various applications in industry with a focus on mechanical engineering and heavy machinery. Our customers come from a wide range of industries: railway, wind power, marine, industrial gearboxes, oil and gas extraction, crane construction or construction machinery as well as special machines. We also supply the retrofit industry and manufacture the parts in small series or individual production. Depending on the dimension a quality of 4 can often be achieved. We examine the possibilities without obligation and without charge. Our customers include renowned and well-known companies. References to your industry on request. We manufacture according to customer drawings and have our own hardening plant. This saves time and costs during production. Cooperation exists for gas nitration and single-tooth induction hardening with experts in their field. ZWP supports you in the overhaul of plants and machines (Retrofit).

We manufacture gears, gear rings and toothed shafts for various applications in industry with a focus on mechanical engineering and heavy machinery. Our customers come from a wide range of industries: railway, wind power, marine, industrial gearboxes, oil and gas extraction, crane construction or construction machinery as well as special machines. We also supply the retrofit industry and manufacture the parts in small series or individual production. Depending on the dimension a quality of 4 can often be achieved. We examine the possibilities without obligation and without charge. Our customers include renowned and well-known companies. References to your industry on request. We manufacture according to customer drawings and have our own hardening plant. This saves time and costs during production. Cooperation exists for gas nitration and single-tooth induction hardening with experts in their field. ZWP supports you in the overhaul of plants and machines (Retrofit).