Blades for canning - Import export

Flexible processing: Highly flexible machine programme for trimmers and splitters for industrial use. The position and number of circular blades can be set individually for the splitter. The variably adjustable cutting width also allows the trimmer to be used as a strip cutter. Advantages Splitting center pieces Variable cutting width Divided discharge belt Modern Hygiene Design

Clean, efficient, versatile. transfluid's knife cutting method is ideal for postbending cuts. Even with extreme geometries it is possible to have perpendicular cuts with sharp edges. In both cases both chips can easily be detected in the process. Extreme requirements are also not a problem, as up to two blades can be used. An internal mandrel can also optimise the process.

secutex has developed the new “TopDrain” structure surface for lifting wet or oily components. Most of the damages at sharp or rough edges are caused by the movement of the load across the sling. In the case of loads with a “sharp edge” or with a very rough surface, a protective sleeve or fixed coating must be used to protect the textile lifting sling. If the load moves sideways, a cutting movement on the edge is the result. Similar to a knife blade, the edge can cut through the fibers of the textile sling. The new “TopDrain” surface drainage provides good adhesion of the protective sleeves and the coated lifting slings even on wet and oily materials. The liquid can drain off into the surface hollows and the load lies securely in the lifting sling. The “TopDrain” structure works like a drainage and ensures the frictional connection of the secutex coating to the load.

The protection against „sharp edges“ Alongside other factors such as temperature, chemical environment and mechanical loads, the „sharp edge“ remains one of the main causes of damage to the lifting accessory itself and frequent cause of accidents. Most damage on sharp or rough edges is the result of load movement perpendicular to the load lifting accessory. If the edge is „sharp“ it can, in a worstcase scenario, cut through the lifting accessory. If the load moves laterally, a cutting movement takes place at the edge. Much like the blade of a knife, the edge can cut through the fibres of the textile lifting accessory. For loads with a „sharp edge“ or with a rough surface, a protective sleeve or fixed coating is recommended to protect the textile lifting strap.

Technical information The AI 02 S3 is a stripping machine driven by an electric motor. Special feature: A special adapted funnel allows to insert two or three wires and strip it in a single step. By turning the stripping blades, the minimal stripping length can be reduced to 3 mm.

-The original BAUER shovel for handling and transporting bulk materials -simple pick-up using forks -can be emptied at any height by cable operated from the driver‘s seat -body walls with reinforced edging -special steel blade trim -sturdy frame -can be secured to prevent slipping Types available -Type BSE mechanical -Type BSE-H hydraulic -Type BSM mechanical, with trough opening for forks -Type BSM-H hydraulic, with trough opening for forks -Type BSI mechanical

• rapid and efficient de-scaling of fish by means of a wide special blade • the waste scale container can be closed with a lid for clean working

This model is well suited for efficient, economical processing of circular workpieces via surface and step grinding operations. There is no lost time through deceleration, acceleration and reversal as with conventional reciprocation grinding. The grinding wheel remains in contact with the workpiece throughout the grinding process. Single workpieces can be located centrically on the table while multiple workpieces can be located concetrically to optimize table space utilization. A tilting table option allows grinding of chamfers or blade edges (i.e. circular blades), where the table can be tilted +/- 5 degrees. The high-precision rotary table is belt driven. This machine is offered with the xpressCube SPS controls package. A software option is available for step grinding operations. Benefit Overview — Compact and robust machine design — High productivity through continuous contact between wheel and workpiece — High long-term precision — Precision rotary table — Easy to operate

Production of bandsaw blades between 50 mm and 311 mm width. Available in the following styles: - toothed - welded - straightened and tensioned - swaged - set - stellite tipped Steel Qualities: - CR-100 swedish - CR-200 extra - CR-300 special - CR-400 PREMIUM - CR-400 Xtreme Coils: Available in both coils (10mm - 311mm) or finished saws (50mm - 311mm), bandsaw blades can be produced as single-sided or double-sided. Blades are also available with variable pitched teeth or with winter teeth.