Alarm systems - Import export

The emergency call alarm system of Klöpper Therm has been designed to improve the safety of your employees in cold stores and to call for help immediately in case of emergency. With the emergency alarm system of Klöpper Therm, entrapped / injured persons become noticeable and additionally a networked PC starts to report the alarm via the ”Wake on LAN function“. Alternatively it is possible to display other technical alarms such as a temperature rise in the store, doors unclosed, water alarm or inactive ventilation. Other applications on request.

Belt width 500-1200 mm (20” to 47”)

Master panel with integrated display for controlling up to 16 I/O components With 9 illuminated buttons, 23 lamps and integrated buzzer Redundant CANbus connection Ideal for use in shipbuilding thanks to approvals from classification societies

Control and display panels with different numbers of lamps and illuminated buttons Can be individually labelled using insertable plates To be used as an extension for a master panel or the central master module NORISYS 4 CPU

Master panel with integrated display for controlling up to 16 I/O components With 12 illuminated buttons, 12 lamps and integrated buzzer Redundant CANbus connection Ideal for use in shipbuilding thanks to approvals from classification societies

The starter kit 2 for the Ajax security system. The kit consists of the hub 2, motion detector with a photo camera to verify alarms, opening detector and key fob with panic button.

The starter kit 2 for the Ajax security system. The kit consists of the hub 2, motion detector with a photo camera to verify alarms, opening detector and key fob with panic button.

The starter kit for the Ajax security system. The kit consists of the hub, motion detector, opening detector and key fob with panic button.

The starter kit for the Ajax security system. The kit consists of the hub, motion detector, opening detector and key fob with panic button.

The Hub intelligent control panel is a key element of the Ajax security system. The device monitors operation of all Ajax detectors and immediately sends an alarm signal to the owner and the Central Monitoring Station.

Wireless outdoor siren that notifies of danger using sound and light. The device is installed outside the room to raise an alarm for everyone to hear.

Wireless combined motion and glass break detector. The device helps to secure the room from intruders entering through doors and windows, and monitors the current state of the glass.

Wireless motion detector with microwave sensor that notifies the owner of first signs of home or office intrusion. Designed for rooms with air conditioners, fireplaces and where there is a likelihood of light flickering, glare and reflections.

Small wireless detector that notifies of glass being broken by intruders. It is installed at a distance of 9 m from the window and filters events that cause false alarms about breakage.

Wireless motion detector that notifies the owner of the first signs of home or office intrusion. The detector is fastened to the wall in front of the doors and other places likely of intruder entry.

LeaksProtect detectors can protect from flood both small apartments and commercial centres/industrial complexes. If an accident happens, informative notifications will let you know where to send the plumbers.

Wireless opening detector that notifies of first signs of room intrusion by means of a broken door or window. It can be mounted on all types of doors including a metal base.

Wireless indoor siren that loudly notifies of an alarm during detector activation. It is installed indoors to warn of danger or deter intruders.

Wireless fire detector with temperature sensor that monitors security in the room twenty four hours a day and immediately notifies of smoke and sharp jumps in temperature.

If mobile phone reception is poor and there is a landline connection available, the automatic telephone dialler is a reliable alternative to fault message transmission by text message. Any fault messages are forwarded to different pre-programmed phone numbers. Product features For forwarding fault messages via the landline. Integrated microphone and control loudspeaker Voice messages to any number of recipients Digital message to one or more alarm receiving systems Remote query, remote control depending on device type Messages to pager or as text message depending on device type

Raytek GS150 thermal imaging systems enable automated quality control in glass bending, forming, annealing, and tempering processes. The GS150LE variant is especially designed for Low-E (low emissivity) glass / one-side coated flat glass. It features automatic emissivity correction. The systems are based on the Raytek MP150 infrared line scanner, which has a max. resolution of 1024 points per line, a max. 150 Hz scanning frequency, and an up to 90° wide field of view. SYSTEM PROPERTIES • Automated temperature monitoring • Visualization on PC • Ethernet TCP/IP interface integrated in the line scanning system • PC-independent alarm output • PC-independent analog outputs 3 x 4 – 20mA BENEFITS • Improve profitability and product quality • Reduce set-up time • Detect defects quickly • Automate quality monitoring for ISO9000 • Reduce scrap • Efficiently manage the heat balance in the oven • Automatically adjust the emissivity value when changing glass types or coatings

Thermal imaging system based on the Raytek MP150 infrared linescanner. Detailed web temperature profile based on 40,000 measurement points per second Automated temperature monitoring Automated quality monitoring for ISO9000 Ensures proper web temperatures for strong film-to-substrate adhesion Enables plant operators to reduce scrap and improve profitability and product quality Quick and automatic detection of “wavy” or “running” edges, gaps, and torn edges Define product-specific configurations (recipes) Automatically analyze “automatic sector” temperature distributions Visualisation on PC Playback stored files as “movie” Multiple language support Integrated OPC server for remote system control Ethernet TCP/IP interface integrated in the line scanning system PC-independent alarm output Analog outputs 3 x 4 – 20mA Analog or digital output modules For sheet extrusion see the Raytek ES150 system.

Car Alarm Police Siren Horn Security Systems 100W DC 12V Car Loudspeaker Horn 5 Tone Siren Horn Car Megaphone Siren Loudspeaker Detail 100W Speaker gives very loud sound about 300 decibels at full volume.

Measurement and control In this sector, MPT represents the interests and products of WALCHEM Corporation in Holliston, Massachusetts (USA). WALCHEM is a leading manufacturer of sensor technology and controllers for the surface technology and for the water treatment technology, including pH-, redox and conductivity controllers as well as special controllers for the cooling-water and boiler water conditioning. Besides the measuring transducer, these controllers include also a control program, adapted to the respective application. Monitoring, alarming – control and telecontrol systems By default, WALCHEM’s WebMaster has available sensors and data amplifiers for various physical parameters. Using the integrated program the parameters can be linked to each other and to control parameters. Via telephone modem and Ethernet board the user is provided with information such as alarm messages and off-limit conditions worldwide.  Measuring and control technology for dosing liquid media in

Statox 501 Infratox detects gases in the LEL and ppm range. Protecting people and assets from hydrocarbons The infrared absorption method of gas detection is ideal to detect hydrocarbons such as fuels. It features enough sensitivity to expand the range of application into the ppm range. For instance fuels such as gasoline, diesel or kerosene are mixtures of hydrocarbons. Infrared gas detection theory of operation Some gases absorb light at a certain wavelength (colour). This absorption band is specific to the gas. The rate of the absorption depends not only on the substance to be detected but also on the number of gas molecules (i.e. the concentration of the gas). This premise is used to detect gases. For example, the C - H bond in hydrocarbon molecules will oscillate and absorb light at 3, 4 mm. This fact makes it so easy to detect fuels. Hexane, for instance has 14 C - H bonds compared to Methane which has only 4! A light beam is directed through a cuvette filled with the gas to be detected. The more hydrocarbons are present, the more light will be absorbed. A photo detector at the other end of the cuvette measures the remaining light intensity. The difference between the original and remaining light intensity corresponds to the gas concentration. A reference beam with a different wavelength compensates for potential interferences of dust, humidity or variations of intensity from the light source. Fail-safe technology Failure of important components such as the light source or photo detector will trigger a "system fail" alarm. Most local authorities will accept this as a self-diagnostic feature. Systems including a self-check require less maintenance and calibration, saving time and money. Simple maintenance: Easy to read display and non-Vintrusive calibration The bright LED display of the Statox 501 Infratox shows the gas concentration in percent L.E.L. (Lower Explosion Limit). An important accessory is the calibration adapter, featuring control buttons operating Hall-sensors inside the Ex d housing. The service menu is password protected preventing unauthorised access. All parameters can be checked and changed, or a calibration can be done all without opening the transmitter. The adapter is also equipped with a gas outlet so that it can be used for flow-through applications. Impervious compact design The dimensions of the Statox 501 Infratox are small and compact. The sensor compartment is completely sealed, not allowing dust or insects to enter. It is located in the center of the sensor head. This allows heat radiation from the electronics and the infrared lamp to keep the unit a few degrees above the ambient temperature thus avoiding condensation. This innovative design makes any additional heating unnecessary, allowing the sensor head to be very energy efficient. This saves additional money by eliminating more expensive wiring and a bigger power supply that would otherwise be necessary. The sensor head is rated protection class IP 67 (6 = protection even against fine dust, 7 = submerged 1 m deep in water for 30 minutes). You can have confidence that this system will safely operate even in the harshest environment.

Fixed gas detection system for oxygen, toxic and combustible gases This DIN – rail mounted modern control module saves space, money and installation time. One safe controller for all gases: Any combination of a sensor head plus control module is a complete gas detection system. This makes the Statox 501 so safe and reliable. The Statox 501 also gives you the opportunity to alter or expand existing systems with minimum cost and labor. Programs for all gases and measuring ranges are permanently stored in the memory of the controller. The user-friendly software program allows authorized personnel to select different configurations by a simple push of a button. Easy to install and easy to use The controll modules as well as the power supply and the common alarm module clip on to a DIN rail. The remote sensor heads and any alarm or recording devices connect to terminals on the front of the module. Each Statox 501 control module has three relays for alarm 1 and 2 and system failure (115 / 230 V AC / 2 A). An analog output for recorder or process control systems is also included. Measured values are displayed on a 4 digit LED-display. It is easy to program or calibrate the Statox 501! Just follow the menu! If intrinsically safe transmitters are to be installed in division 1 areas, they can be connected via intrinsically safe repeaters. 24 V power supply as well as the signals for the common alarm module are transmitted via bus from one module to the next. All terminals are easily accessible from the front. Field proven sensors for reliable gas detection Compur manufactures electrochemical sensors for the detection of oxygen deficiency and toxic gases. These sensors generate an electrical current proportional to the actual gas concentration. The remote sensor heads are designed as intrinsically safe certified 4 - 20 mA transmitters and have an integrated concentration display. Combustible gases can be detected with a variety of catalytic beads (pellistors) or infrared technology. The sensor heads are certified "Ex d" or "Ex de" and can be connected directly to the control module, even if they are to be used in classified areas. The control module can supply and operate different designs of catalytic sensors. With so many possibilities, the system can easily be tailored to suit your individual application needs. Easy maintenance saves time and money Maintenance of the 4 – 20 mA transmitters is very easy. A one-man calibration or replacement of the sensors can be done without further precautions, even in classified areas. Accessories A range of wall-mount cabinets for a maximum of 5, 8 or 32 controllers as well as a 19”-carrier, ensure an easy professional installation. -20 - +60 °C

Compur Statox 502 Control - and Common Alarm Module The All – Rounder in Gas Detection No matter if you want to detect toxic or combustible gases: This control module works with any sensor head. It provides the power supply and processes the signal. Three highly rated relays and a 4 – 20 mA output are the interfaces to peripheral instrumentation. Potential front ends may be the Statox 501 or Statox 505 transmitters with electrochemical or infrared sensors, or sensor heads with a Wheatstone bridge signal such as Statox 501 PID, catalytic or the Statox 501 LC and MC series with infrared sensors. Just by the push of a button you can program the module to handle 4 – 20 mA sink or source. Even the bridge voltage can be set to any value between 2 and 5.2 V, it even works with sensor heads of other manufacturers. So there is no restriction at all when selecting the appropriate sensor head for you application. With its two “sense” lines it can even compensate the voltage drop in the cable for very remote sensor heads or if there are extreme temperature variations. For maximum flexibility the measuring range is user programmable. You can also select the unit, no matter if it is ppb, ppm, % LEL or % volume. Easy installation The control module is mounted on a standard DIN rail. With an optional power rail you can interface the 24 V DC power and the alarm signals. This way you can program one of the modules to operate as a common alarm module. Even this function can be programmed just by push button. The application of a control module as a common alarm module is a very useful feature. It displays when any of the modules goes into Alarm 1, 2 or system alarm, and controls peripheral alarm devices. All electrical contacts are located easily accessible on the front side. The terminals for alarm signals, analog output, sensor head connection run into 6 pluggable terminal blocks. This makes not only the first installation quick and easy, but also any service event or system modification. A module can easily be removed out of its row, without interrupting its neighbors or disconnecting wires. Intuitive User Interface You want a gas detection system that needs little or no attention. No matter if setting the initial parameters or performing scheduled calibrations or proof tests: The handling shall be safe, quick and easy. The password - protected Statox 502 software structure is so clear that most menu items are self - explanatory. The “Reset” button brings you time back into the measuring mode at any time. Even if you have to interrupt your work and forget to reset, the watchdog function returns the system into the measuring mode, if no button has been pushed for a while. Functional safety paired with utmost system flexibility The Statox 502 complies with the standards DIN EN 61508 and 61511 functional safety, level SIL 2. In context with the HRC or ARE sensor heads you can create a complete gas detection system for combustible gases complying with SIL 2 standard. In larger installations signals of gas detectors often run into SIL certified process control systems, in smaller plants there is a need for a control module complying with SIL requirements. As any combination sensor head / control module forms a complete gas detection system, this system closes the gap. It is expandable without limits, and there is no restriction to the mix of sensor heads connected. Connecting other front ends The versatility of the Statox 502 does not end with gas detection. You can connect any front end providing a 4 – 20 mA analog signal or a Wheatstone bridge signal. So you can create your own compact control system for a variety of sensors with just one type control device. Accessories Useful accessories such as calibration adapters, intrinsically safe repeaters, Power supplies etc. complete the system. 205 VAC, 8 A min. make or break power >/= 12 V, 10 mA, contakte silver / nickel

PROCONTROL Precise metering and constant pressure of sealing water (p = 1 bar above media pressure) - environmental protection and cost reduction in fact of reduced seal water consumption Flow and pressure monitoring - protects the aggregate from failing (inductive alarm system) Stable and compact construction guarantees safety and simple handling Corrosion and temperature resistant Displays are easy to read and clean With an inductive switch (special component) alarm system can be used. Technical parameters Flow range 0.5 up to 1.5 ltr/min 0.5 up to 3.0 ltr/min 1.0 up to 8.0 ltr/min 2.0 up to 15.0 ltr/min Temperature: t = … +80 °C Pressure: p = 10 bar (Option 25) Main application Pumps with mechanical seals with flush port Stuffing box packings with lantern rings Suitable for All Industries Accessories and options Pressure valve for creating blocking pressure Pressure Gauge Stand Inductive switch Hoses, connecting...

Slave display for alarm extension systems and duty alarm systems Cabin unit for alarm extension systems and duty alarm systems (e.g. for ship cabins, mess room, office, bridge, etc.) Display of measurement value channels, channel statuses and alarms from the automation systems (e.g. IAMCS) Visual and acoustic alarm triggering Acoustic and visual fire alarm signalling from an external, independent fire alarm system (type N3000-DSP20 only) Ideal for use in shipbuilding thanks to approvals from classification societies