Drive shafts - Import export

GRF – Geared agitator with parallel shaft geared drive The agitator shaft of the GRF series geared agitator is directly mounted in the hollow shaft of the parallel shaft geared drive. Thus, no additional bearing housing is necessary. The gear bearings are adequately dimensioned and fully adapted to the requirements. The GRF series is suited for a wide range of applications thanks to shaft lengths of up to 6,000 mm and drive ratings of up to 75.0 kW. It has a standard output speed of 1 to 400 rpm. The agitator shafts are balanced for concentric run after assembly of the mixer. Upon request, we supply the GRF series with frequency controlled drive that has drive ratings of up to 7.5 kW. Type test certificate for explosive zone 0.

The tote tank mixers CR-E are designed for operation on plastic containers with filling openings of 150 mm and volumes from 600 l up to 1,200 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. The fixing of the traverse bridge is adjustable for various container models. The impellers are designed to fit through the filling opening 150 mm when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker.

The tote tank mixers CR-M are designed for operation on stainless steel containers with filling openings of DN 400 mm and mixing volumes from 400 l up to 1,500 l. Depending on the viscosity of the mixing material, CR-Ms with fast running or gear reduced drives are available. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gear). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening DN 400 when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker. The electric container mixers can also be supplied with frequency converter drives. All CR-M series mixers can be supplied as follows:

The tote tank mixers CRP-E are equipped with a pneumatic drive. It has been especially designed for plastic IBCs with filling openings of at least 150 mm and volumes from 600 l up to 1,200 l. The fast running pneumatic agitators are equipped with bearing and coupling housings. By means of the maintenance unit, pressurized air is enriched with oil for the vane drive. The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. Folding propellers that fit through the filling opening DN 150 mm are used for geared agitators. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. Explosion-proof mixers are also feasible.

The FR series is a fast running electric drum mixer that can directly be mounted on 200 l steel drums with a 2“ bung hole. The mounting on the drum is done with a 2” threaded adapter with which the agitator is screwed into the bung hole. The agitator shaft is connected to the drive shaft by means of a sleeve coupling. Folding propellers are used as mixing elements, which can be inserted into the drum through the 2” bung hole when being folded. The FR series mobile mixer is delivered as a turn-key solution with an on-/off-switch with low voltage breaker and connection cable. Upon request, the FR series mixer can also be supplied with an integrated frequency inverter. Additionally we can provide you with a vessel clamp applicable for open lid drums.

The LRD series top-entry sealed agitator can be used for mixing in closed containers with a mechanical seal. It is designed with a coupling housing. The agitator shaft is borne in the bearing housing and the mechanical seal (single- or double-acting). The seal can be exchanged without dismantling the mixer from the tank (also in case of a side entry). Drives with shaft journals for LRD series: Three-phase motor Helical geared drive unit Parallel shaft geared drive unit Variable speed geared drive unit Helical bevel geared drive unit According to the tank size, the LRD series agitator is available in four different frame sizes. Shaft diameters of 30 mm to 90 mm and shaft lengths of up to 10,500 mm are feasible. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3). Pharmaceutical version with FDA and GMP feasible.

CR-M - Electric tote tank mixer for stainless steel IBCs The tote tank mixers CR-M are designed for operation on stainless steel containers with filling openings of DN 400 mm and mixing volumes from 400 l up to 1,500 l. Depending on the viscosity of the mixing material, CR-Ms with fast running or gear reduced drives are available. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gear). The agitator shafts are balanced for concentric run after assembly. The mixer is mounted on the container’s manway lid, which is clamped with butterfly screws or a clamp ring. The manway lid is supplied by the container manufacturer or by the customer. The impellers are designed to fit through the filling opening DN 400 when being inserted. The electric container mixers are delivered with on-/off-switches with low-voltage breaker. The electric container mixers can also be supplied with frequency converter drives. All CR-M...

FR - Electric drum mixer The FR series is a fast running electric drum mixer that can directly be mounted on 200 l steel drums with a 2“ bung hole. The mounting on the drum is done with a 2” threaded adapter with which the agitator is screwed into the bung hole. The agitator shaft is connected to the drive shaft by means of a sleeve coupling. Folding propellers are used as mixing elements, which can be inserted into the drum through the 2” bung hole when being folded. The FR series mobile mixer is delivered as a turn-key solution with an on-/off-switch with low voltage breaker and connection cable. Upon request, the FR series mixer can also be supplied with an integrated frequency inverter. Additionally we can provide you with a vessel clamp applicable for open lid drums.

CR-E - electric tote tank mixer for plastic IBCs The tote tank mixers CR-E are designed for operation on plastic containers with filling openings of 150 mm and volumes from 600 l up to 1,200 l. The customer may choose between various viscosity-related basic versions of fast-running and slow-running mixers with electric drives. The agitator shafts are connected to the drive shafts with sleeve couplings or borne within the gear’s hollow shaft (worm gears). The agitator shafts are balanced for concentric run after assembly. CR-E 6 0,75 The mixer is mounted on a container traverse bridge, which is included in the scope of supply and clamped with a rapid fixing system to the cage frame of the IBC. The plastic bulk of the container is therefore not harmed by any static or dynamic loads by the agitator. The fixing of the traverse bridge is adjustable for various container models. The impellers are designed to fit through the filling opening 150 mm when being inserted. The electric...