Distributor of waters - Import export

PROCESS DATA MEASUREMENT AND PROCESS CONTROL ON HIGHEST LEVEL AND MAINTENANCE-FREEFollowing the user‘s request for easy maintenance and low susceptibility to slightly soiled water, the proflow ultrasonic - as a replacement for the current and widely used standard measuring variant with impeller, turbine or vortex - now makes contactless measurement according to the ultrasonic principle (without rotating parts) available. The sensors can be visualized via a protemp controller or connected to a PLC. Alternatively, the mechanical flow measurement according to the differential pressure principle is available with the proflow mechanical. Easy to integrate in machines and plant lines 4 or 6 x consumer channels (forward/return) 1/2“ With LED-display on fl ow sensor Temperature measurement PT 1.000 Big RED/GREEN Status LED 1 x main connection 1“ Flow rate each channel 1 ... 30 l/min (no „overload-risk“-> 60 l/min possible]) Operating temperature: 0 ...120 °C

The »speedfit« compressed air piping system is characterised by its simple and fast installation and it is ideally suited for conveying compressed air and liquids. It is installed without tools and the connections can be quickly fastened and released with additional sealing material not required. The »speedfit« compressed air piping system is fabricated according to BSX 5750 Part I, ISO 9001, EN 29001. The good flow properties and large range of products characterise this system. Plastic pipes, aluminium pipes, air distributor sockets, pipe clamps, water separators, loosening assists, brass connectors, protective caps and retaining rings are included in the »speedfit« series.

The »speedfit« compressed air piping system is characterised by its simple and fast installation and it is ideally suited for conveying compressed air and liquids. It is installed without tools and the connections can be quickly fastened and released with additional sealing material not required. The »speedfit« compressed air piping system is fabricated according to BSX 5750 Part I, ISO 9001, EN 29001. The good flow properties and large range of products characterise this system. Plastic pipes, aluminium pipes, air distributor sockets, pipe clamps, water separators, loosening assists, brass connectors, protective caps and retaining rings are included in the »speedfit« series.

The multiple water quantity control system in modular design that is available in several versions fulfils not less than three requirements at the same time. It combines the advantages of the conventional water distributors, the impulse cooling systems and the continuously operating temperature control units while eliminating the disadvantages of each of these systems. The temperature control system disposes of up to 128 individually adjustable circuits and is suitable for the processing of polyolefins and technical thermoplastic materials. In case of the basic execution (itd B) the requested flow rate is adjusted manually and is then monitored by a flow meter and presented digitally and graphically on the central display of the control unit. In the standard execution (itd R) the water quantity is individually set for each circuit at the central operating unit and - if necessary - is readjusted automatically via a water quantity regulation valve within adjustable limit values.

PROCESS DATA MEASUREMENT AND PROCESS CONTROL ON HIGHEST LEVEL AND NEARLY MAINTENANCE-FREEFollowing the user‘s request for easy maintenance and low susceptibility to slightly soiled water, the proflow mechanical - as a replacement for the current and widely used standard measuring variant with impeller or turbine - now makes mechanical measurement according to the differential pressure principle (without rotating parts) available. The sensors can be visualized via a protemp controller or connected to a PLC. A completely non-contact flow measurement based on the ultrasonic principle is available with the proflow ultrasonic. Robust flow measurement in consumer return line PT 1.000 temperature measurement in consumer return line 6 x 2 consumer channels 3/4“ female screw thread 1 x 2 main connection 1“ female screw thread Available in three temperature variants: operating temperature up to 100°C, up to 160°C and up to 180°C Max. flow rate each channel:: 25 l/min or 50 l/min

HIGH PERFORMANCE TEMPERATURE CONTROL DEVICE WITH HIGH COOLING CAPACITY, HIGH FLOW RATE AND REDUCED ENERGY CONSUMPTION. Due to the design, dimensioning and selection of the used components, enersave temperature control systems are the most efficient systems on the market with the highest flow rates at operating point. In the selection series we used the most frequently selected equipment features and heating performance of the proven premium series advanced. The protemp selection temperature control unit is particularly suitable for the supply of multi-circuit water distributors and is designed for the display of up to 6 external proflow temperature control channels.

COFFEE SPRINTER – The single cup coffee brewer, pour over for fresh coffee. The single-cup coffee brewer is the perfect solution for ultimate freshness. Place the COFFEE SPRINTER on your mug and introduce 2 tablespoons of ground coffee into the filter. The water distributor is inserted to press the ground coffee flat to the stainless-steel mesh at the bottom. Add some hot, not boiling water (appr. 50 ml ) and wait for 20 seconds to allow the ground coffe to swell up. Fill with hot water and pülace the lid on top (caution: observe cup/mug capacity). Hot water passes the ground coffee and fills the mug below. As soon as the water goes through the filter, remove the lid, turn it upside down, then place the filter on the lid which is now serving as a drip-off tray. Enjoy great coffee! Highlights fits most cups and mugs, from 7,1cm to 8,6cm micro-fine stainless-steel mesh water distributor for consistent extraction of the ground coffee lid serves as drip-off...

SANHA stainless steel heating circuit distributors are suitable for all hot water heating systems in accordance with EN 12828, and for panel heating / cooling systems in accordance with EN 1264, and can therefore be used not only in residential buildings, but also in industrial, commercial and public buildings.

Stainless steel heating circuit distributors are suitable for all hot water heating systems in accordance with EN 12828, and for panel heating / cooling systems in accordance with EN 1264, and can therefore be used not only in residential buildings, but also in industrial, commercial and public buildings. They are used for the distribution of water and for isolating and balancing flow in heating and cooling circuits. This means that they can be used for the connection of radiators, ventilation / air conditioning units, as well as wall, ceiling and floor heating / cooling systems. Venting, flushing and flow balancing are particularly important to ensure trouble free and optimum operation in floor, wall and ceiling heating and cooling systems. The SANHA heating circuit distributors are equipped as standard with a safety filling and ventilation device as well as integrated flow meters or control valves. This allows a reliable, fast and thus cost-efficient execution of these measures.

Stainless steel heating circuit distributors are suitable for all hot water heating systems in accordance with EN 12828, and for panel heating / cooling systems in accordance with EN 1264, and can therefore be used not only in residential buildings, but also in industrial, commercial and public buildings. They are used for the distribution of water and for isolating and balancing flow in heating and cooling circuits. This means that they can be used for the connection of radiators, ventilation / air conditioning units, as well as wall, ceiling and floor heating / cooling systems. Venting, flushing and flow balancing are particularly important to ensure trouble free and optimum operation in floor, wall and ceiling heating and cooling systems. The SANHA heating circuit distributors are equipped as standard with safety filling and ventilation device as well as integrated flow meters or control valves. This allows a reliable, fast and thus cost-efficient execution of these measures.

SANHA stainless steel heating circuit distributors are suitable for all hit water heating systems in accordance with EN 12828, and for panel heating / cooling systems in accordance with EN 1264, and can therefore be used not only in residential buildungs, but also in industrial, commercial and public buildings. Ball valve set

stainless steel heating circuit distributors are suitable for all hot water heating systems in accordance with EN 12828, and for panel heating / cooling systems in accordance with EN 1264, and can therefore be used not only in residential buildings, but also in industrial, commercial and public buildings. They are used for the distribution of water and isolating and balancing flow in heating and cooling circuits. This means that they can be used for the connection of radiators, ventilation / air conditioning units, as well as wall, ceiling and floor heating / cooling systems. Venting, flushing and flow balancing are particularly important to ensure trouble free and optimum operation in floor, wall and ceiling heating and cooling systems. Connection set, vertical, for heat meter, with 3 ball valves, variable adaptor pipe 3/4" 110 mm (1" 130 mm), tee for sensor