Direct media - Import export

The ViscoMT-XS hobbock emptying system offers a modern way of emptying containers.The following advantages result from the use of eccentric screw pumps for the removal of the medium: - container sizes from approx. 5 l to 50 l - viscosities of approx. 80,000 - 2,000,000 mPas - very low shear stress of the medium - very low pressure load of the medium (max. 18 bar) - Removal of media loaded with fillers - no backflow within the sampling pump - electrical control of the pump with pressure control - valve-free pump system - no material pressure reducer necessary due to electronic pressure adjustment - very good residual emptying (less than 1% residue) - electronic "empty" and "almost empty" message Application: - Removal of media directly from the delivery container, e.g. silicones, adhesives, resins, greases, colour pastes, metal-filled pastes (Cu and Ni solder pastes, Al and Ag pastes) - supply of media to dispensers - direct dosing as pulsation-free flow rate

The reinforced version of the type 8037 sliding gate motor valve is suitable for use in potentially explosive atmospheres in accordance with Directive 94/9EG. Media such as steam, liquids, gases etc. can be excellently controlled with this motor valve, even in hazardous areas. Metal bellows Position electronics Analog stroke feedback Limit switch . . . Ex zones 1, 2, 21 and 22 Protection class I 2G Ex de (ia) IIC T6/T5 or T4 (gas version) Protection class II 2D Ex tD (iaD) A21 IP 66 T80C (dust version)

The sliding gate motor valve type 8037 is suitable for the intended use in potentially explosive atmospheres according to Directive 94/9EG. Media such as steam, liquids, gases etc. can excellently be controlled with this motor valve, even in hazardous areas. Metal bellows Position electronics Analog stroke feedback Limit switch . . .Ex zones 1, 2, 21 and 22 Protection class I 2G Ex de (ia) IIC T6/T5 or T4 (gas version) Protection class II 2D Ex tD (iaD) A21 IP 66 T80C (dust version)

The cartridge emptying ViscoMT-C offers the possibility to empty 180 ml cartridges, 310 ml Euro cartridges and 600 ml or 950 ml cartridges in industrial use. Your advantages: - Plunger without direct air supply - Supply of media to the dispenser(s) - Venting option after cartridge change - electrical "empty" and "almost empty" message Controls: - Pressure sensor for inlet pressure control - Pneumatic pressure reducer for pre-pressure adjustment Application: - for low-viscosity media up to viscous media - Media examples: Silicones, adhesives, resins, greases, color pastes, metal-filled pastes Necessary and optional components: Dispenser suitable for dosing (separate article)

Pressure Compensated Throttle Check Valves PNDRV ▪ Throttle and shut-off the flow of liquid media in direction A-B (free flow in reverse direction) ▪ With pressure compensating feature via built-in compensating piston ▪ Designed for in-line assembly with female BSP, NPT and SAE threaded connections ▪ Graduated turning knob to accurately control flow ▪ Set-screw located on side of turning knob to lock valve in position ▪ Panel mounting nuts available on request ▪ Maximum working pressure: 210 bar / 3000 PSI

The Dosing Mass flow Meter extends the range of Dosing Sensors with special attention to the dosage of non-conductive media and direct mass dosage. The devices are designed in a very compact way and can be connected directly to the Compact Controller. The sensor outputs are compatible to those provided by our magnetic-inductive flowmeter with Converter Card UV14. As a minimum configuration, 24 VDC supply, valve input and pulse output can be connected. The pulse factors are adapted to the magnetic-inductive flow meter, so that the devices can be interchanged easily. Advantages • compact design • direct measurement of mass • measurement of non-conductive media • very short dispensing time down to 250ms • high accuracy / repeatability • no moving parts • easy to clean compared with piston filler • product gentle filling Flexibility • DN 10, 15, 20, 25 • liquid temperature 0°C to 90 °C • different connections available such as: • Tri Clamp acc. DIN 32676 • Sanitary thread acc. DIN 11851

Throttle Valves for In-Line Assembly DV ▪ Throttle and shut-off the flow of liquid media in both directions ▪ Designed for in-line assembly with female BSP, NPT and SAE threaded connections ▪ Graduated turning knob and coded spindle to accurately control flow ▪ Set-screw located on side of turning knob to lock valve in position ▪ Panel mounting nuts available on request ▪ Maximum working pressure: up to 350 bar / 5000 PSI Throttle Valves for Manifold Mounting DVP ▪ Throttle and shut-off the flow of liquid media in both directions ▪ Designed for manifold mounting with either 4 or 6 mounting holes ▪ Graduated turning knob and coded spindle to accurately control flow ▪ Set-screw located on side of turning knob to lock valve in position ▪ Panel mounting nuts available on request ▪ Maximum working pressure: up to 350 bar / 5000 PSI Throttle Valves for Cartridge Assembly DVE ▪ Throttle and shut-off the flow of liquid media in both directions ▪ Designed for direct installation into...