Results for
SHENZHEN PROMOSTAR HARDWARE CO.,LTD
Germany
These are the accessories mainly used in water sports accessories.
Request for a quoteIGUS® GMBH
Germany
The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes Chip tests in the igus® laboratory demonstrate the tremendous chip-proof properties of the igus® RX tube. Chip-proof - for all types of chips and applications RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips Submersion test in water - Various tube types were submerged under water. The new RX tube needs over 30 seconds until it is filled up, thus proving its high leak tightness Y = time in seconds A = igus® products B = competitor Chip penetration test - Various types of tube were exposed to a defined quantity of chips. In the new RX tube, after 80,000 cycles only 0.2 g of chips were found in the interior Y = chip mass [g] A = igus® RX e-tube RX40.100.100 251.900 cycles B = igus® e-tubes 68.10.100.0 256.132 cycles C = test tube 01 250.907 cycles D = test tube 02* 2.600 cycles *Teststop after 2.600 cycles E = igus® products F = competitor E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Productfinder Assembly instruction Dismantling / assembling a cover, replacing a chain link and assembling / inserting the RX tube. Assembly instruction Configure interior separation Define cables, select chain and configure interior separation. Now also for RX tubes! Interior separation configurator Application examples Applications in various industrial sectors. RX tubes Series RX - new chip-proof design, small pitch, removable cover 1 Chip-proof design without undercuts and edges 2 Excentric locking 3 Material igumid G 4 rounded shape 5 covered pin/hole connection RX tubes IP tested Technical report TÜV NORD red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips
Request for a quoteRK ROSE+KRIEGER GMBH
Germany
Light Clamps – the clever plastic series: With the plastic tube connectors from the "Light Clamps" series, RK Rose+Krieger has developed a cost-effective and versatile range of tube connectors for the positive connection of tubes in the light load range. This design enables the clamping of the most various tube sections and –diameters. Besides their attractive design and the intelligent system of reducing bushes the clamping elements are characterised especially by their resistance to chemicals. They are particularly appropriate for sensitive applications under laboratory conditions and for industrial applications as, for instance, in the beverage or packing industry.
Request for a quoteA.E.T. KUNSTSTOFFE GMBH
Germany
"very strong adhesion to the sub-material high resistance to UV rays toxicologically harmless with normal use Vibration-inhibiting when used in the machine area Millions of people hold plastic products in their hands every day without being aware of this fact. Regardless of whether they are used on sports equipment, medical equipment or work equipment: What is certain is that the pleasant haptic impression - the ""experience of access"" - is an important purchase criterion for the buyer, along with design and functionality. "
Request for a quoteA.E.T. KUNSTSTOFFE GMBH
Germany
A.E.T. is one of the few German companies that co-extrude heat-shrink tubing. In addition to the required order information, all that is required is a production sample for precise dimensions. From prototype development to high-volume series production, A.E.T. offer all quantities. An A.E.T. customer advisor will be happy to answer any further questions with you in a telephone conversation.
Request for a quoteA.E.T. KUNSTSTOFFE GMBH
Germany
Sheathing of e.g .: roof rack rails, impact protection for Kettcars, spring protection and much more.
Request for a quoteMÖLLER VERBINDUNGSELEMENTE GMBH
Germany
Tie chain with plastic tube
Request for a quoteRK ROSE+KRIEGER GMBH
Germany
RK tube connectors – the flexible alternative to welded connections The clampable tube connectors from RK Rose+Krieger are a cost-efficient solution for the positive and ready detachable connection of a diverse variety of systems – without the need for drilling and welding. Depending on the field of application and the expected load, RK Rose+Krieger offers tube connectors made of plastic (Light Clamps), aluminium (Solid Clamps) or stainless steel (Robust Clamps). The Solid Clamps tube connector system also includes the RK monitor mounting for the fixation and ergonomic adjustment of monitors and touch screens used in industrial applications. Say goodbye to welding – that could be the motto of the clampable RK tube connectors The simple assembly technology of the clamping elements eliminates the need for time-consuming and cost-intensive drilling and welding work.
Request for a quotePFLITSCH GMBH & CO. KG
Germany
PFLITSCH offers various hoses to provide comprehensive protection against mechanical and thermal damage to cables, for example where cables are installed in a corrosive environment or where cables run across the floor between a machine and a mobile operating enclosure. The UNI Dicht® system has suitable solutions in metal and plastic for safe connection of hoses to cable glands in these situations. Clampless variants are most suitable e.g. for the food industry, where no contamination or dirt is allowed to build up. These variants have all the advantages of the UNI Dicht® system, including a excellent seal up to IP 68, superior strain relief values, EMC and Ex-compatibility as well as great versatility of application. Also available are cable glands for Smooth hoses Spring-stiffened UL hoses Hoses with external steel braid Availability in sizes from M6 to M120 and Pg 7 to Pg 29.
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Cable conduits made of PP with plug-in sleeve Manufactured acc. to DIN 16878 or prEN 14285 Standard design: Sleeve type: integrally moulded plug-in sleeve (SM) Sealing ring: compression lip sealing ring, type “SX” (inserted in the factory) Sharp end: with plug-in depth marking and chamfer Length: 6 m Colour: black Inner surface: smooth Possible designs: Length: 1 m to 6 m Coloured stripes: co-extruded Colour: on request Outer surface: coloured co-extruded or solid dyed Inner surface: inner grooves for reducing the cable pull-in forces Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Cable conduits made of PVC-U with plug-in sleeve Manufactured acc. to DIN 16875 Standard design: Sleeve type: plug-in sleeve Sealing ring: inserted in the factory Sharp end: with plug-in depth marking and chamfer Length: 6 m Colour: black/anthracite Possible designs: Länge: 1 m to 6 m Farbe: special colours are available on request Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Split pipes made of PVC-U with snap-on locking For the subsequent protection of cables, which have already been laid, or for repairing damaged pipe systems. - sealed against fine sand - reusable - extandable to any length - the joining of the split pipes does not require any tools - a continuous pipeline is achieved by offsetting the top split pipe (no sleeves required) Use as a repair split pipe: Our split pipe is constructed in a way that the locking mechanism is on the outside of the pipe, which means that the inner diameter of 100 mm is fully usable without dimensional limitations. Therefore, the split pipe can be clamped over the defective cable conduit like a plaster over a wound. Standard design: Material: PVC-U Locking system: snap-on lock Colour: grey Length: 3 m Possible designs: Length: 1 m to 3 m Colour: special colours are available on request Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Split pipes made of PE-HD with snap-on system For the subsequent protection of cables, which have already been laid, or for repairing damaged pipe systems - Sealed against fine sand - Reusable - No sleeve required - Extendable to any length - The joining of the split pipes does not require any tools - A continuous pipeline is achieved by offsetting the top split pipe (no sleeves required) Use as a repair split pipe: Our 120 mm x 5,0 mm split pipe is constructed in a way that the locking mechanism is on the outside of the pipe, which means that the inner diameter of 110mm is fully usable without dimensional limitations. Therefore, the split pipe can be clamped over the defective cable conduit like a plaster over a wound. You don’t need to saw off the damaged pipe section! Standard design: Material: PE-HD Locking system: snap-on locking Colour: black Length: 3 m
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Split Pipes made of PP with clamp locking For the subsequent protection of cables, which have already been laid. - Sealed against fine sand - Reusable - Including moulded sleeve - Extendable to any length - The joining of the split pipes does not require any tools - Can be angled by 10° per meter in each direction - 3 red locking clamps are pre-mounted Standard design: Material: PP Locking system: clamps Colour: black Length: 1 m
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Cable cover plates Manufactured acc. to DIN 54841-5 Standard design: Material: PE-HD Lengths: 1.000 mm Surface colour: red Thickness: 2 mm Labelling: Achtung Starkstromkabel Longitudinal locking: using the Z.I.S. Easy Lock System Possible designs: Cover width: 100 mm to 300 mm Length: 300 mm to 3.000 mm Thickness: 1 mm to 3 mm Material: PE-HD or PVC-U Colour Surface: yellow, blue, green, orange, black Longitudinal locking: with or without Z.I.S. Easy Lock System Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Cable cover plates with increased mechanical protection Manufactured acc. to DIN 54841-5 Standard design: Material: PE-HD Length: 1.000 mm Surface colour: red Thickness: 10 mm Labelling: Achtung Starkstromkabel Longitudinal locking: with punched holes and connection pin Possible designs: Cover width: 100 mm to 290 mm Length: 300 mm to 3.000 mm Thickness: 3 mm to 12 mm Material: PE-HD or PVC-U Surface colour: yellow, blue, green, orange, black Longitudinal locking: with or without punched holes and connection pin Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Gabled cable cover Manufactured acc. to DIN 54841-5 Standard design: Material: PE-HD Length: 1.000 mm Surface colour: red Thickness: 2 mm Labelling: Achtung Starkstromkabel Longitudinal locking: using the Z.I.S. Easy Lock System Possible designs: Cover width: 100 mm to 220 mm Length: 300 mm to 3.000 mm Thickness: 1 mm to 3 mm Material: PE-HD or PVC-U Surface colour: yellow, blue, green, orange, black Longitudinal locking: with or without Z.I.S. Easy Lock System Labelling: acc. to customer specifications
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
Z.I.S. KUNSTSTOFF GMBH
Germany
Cable cover tape manufactured acc. to DIN 54841-5 Standard design: Material: PE-HD Roll length: see below Surface colour: see below Thickness: see below Labelling: Caution – High-Voltage Cable Possible designs: Cover width: 50 mm to 300 mm Length: 25 m to 100 m Thickness: 1 mm to 7,5 mm Surface colour: red, blue, green, black Longitudinal locking: with or without (> 3 mm without) Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Corrugated cable spacers We recommend the use of our Z.I.S. Kunststoff corrugated cable spacers for laying cables, wires and pipes next to each other while ensuring the required distance between them (e.g. separation of high-voltage and low-voltage cables). Standard design: Material: PVC-U Colour: black Length: 1 m Possible designs: Colour: on request Length: 0,25 m and 1,5 m
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Pole and wall channels Z.I.S. Kunststoff cable channels for wooden poles made of PVC-U offer reliable protection for your cables and wires against external influences. They are highly resistant against impact, sunlight and weather. Standard design: Material: PVC-U Colour: grey Length: 3 m Mounting: bores with a 7 mm diameter Possible designs: Colour: on request Length: on request Labeling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Standard design: Material: PE-HD Length: 1.000 mm Surface colour: red Thickness: 2 mm Labelling: without Longitudinal locking: using the Z.I.S. Easy Lock System Possible designs: Cover width: 40 mm to 111 mm Length: 300 mm to 3.000 mm Thickness: up to 3 mm Material: PE-HD or PVC-U Surface colour: yellow, blue, green, black Longitudinal locking: with or without Z.I.S. Easy Lock System Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Composite cable conduit made of PE-HD with outer corrugation in coils Manufactured acc. to DIN EN 61386-24 Standard design: Type: with outer corrugation and inner pipe Typ: 450 N Sleeve type: double plug-in sleeve, sand-tight design Material: PE-HD Length: 50 m in coils, with inside cable pull-in aid Colour outer surface: black Possible designs: Sleeve type: double plug-in sleeve, water-tight design Length: on request Colour: red, yellow, blue, green or orange
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Composite cable conduit made of PE-HD with outer corrugation Manufactured acc. to DIN EN 61386-24 Standard design: Type: with outer corrugation and inner pipe Type: 450 N Sleeve type: double plug-in sleeve, sand-tight design Material: PE-HD Length: 6 m Colour outer surface: black Possible designs: Sleeve type: double plug-in sleeve, water-tight design Length: on request Colour: red, yellow, blue, green or orange
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Cable conduits made of PE-HD with plug-in sleeve Manufactured acc. to DIN 16876 Standard design: Sleeve type: integrally moulded plug-in sleeve (SM) Sealing ring: compression lip sealing ring, type “SX” (inserted in the factory) Sharp end: with plug-in depth marking and chamfer Length: 6 m Colour: black Inner surface: smooth Possible designs: Quality: DIN 16874 Length: 1 m to 6 m Coloured stripes: co-extruded Colour: on request Outer surface: coloured co-extruded or solid dyed Inner surface: inner grooves for reducing the cable pull-in forces Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Telecommunication pipe – cable conduits made of PE-HD on drums or in coils Z.I.S. cable conduits made of PE-HD, manufactured acc. to DIN 16874 with external supervision by MPA, Darmstadt or DIN 16876 Standard design: Material: PE-HD according to DIN requirements Colour: black Inner surface: inside grooves, to reach max. pulling-in and blowing-in length Delivery type: on rental drums or in coils Labelling: to DIN requirements Possible designs: Material: PE80/PE100 acc. to DIN 8074/8075 Coloured: coextruded stripes Outer surface: coloured co-extruded or solid dyed Inner surface: smooth Type: composite pipes – side by side, parallel, loose wound on reel Delivery type: one-way-drums Individual length: on drums or in coils Labelling: acc. to customer specifications SDR types: SDR 33 – SDR 11
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Cable cover plates on roll Manufactured acc. to DIN 54841-5 Standard design: Material: PE-HD Roll length: 25 or 50 m Surface colour: red Thickness: 2 mm Labelling: Achtung Starkstromkabel Longitudinal locking: using the Z.I.S. Easy Lock System Possible designs: Cover width: 100 mm to 300 mm Length: 25 m to 50 m Thickness: 1 mm to 3 mm Surface colour: yellow, blue, green, orange, black Longitudinal locking: with or without Z.I.S. Easy Lock System Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Cable conduits made of PVC-U with adhesive sleeve Manufactured acc. to DIN 16875 Standard design: Sleeve type: adhesive sleeve Sharp end: onesided with chamfer Length: 6 m Colour: black/anthracite Possible designs: Length: 1 m to 6 m Colour: special colours are available in request Labelling: acc. to customer specifications
Request for a quoteZ.I.S. KUNSTSTOFF GMBH
Germany
Split pipes made of PVC-U with H-profile For subsequent protection of cables, which have already been laid, or for repairing damaged pipe systems. - Sealed against fine sand - Reusable - No sleeve required - Extendable to any length - The joining of the split pipes does noch require any tools - A continuous pipeline is achieved by offsetting the top split pipe (no sleeves required) The joining is achieved by connecting the two split pipes. The connection battens (H-profile) are glued on one side. A continuous pipeline is achieved by offsetting the top split pipe (no sleeves required). In addition, the H-profiles can be joined to the split pipes during the final assembly using Tangit plastic glue for PVC-U. Standard design: Material: PVC-U Locking system: H-profile Colour: black Length: 3 m
Request for a quoteSANHA GMBH & CO. KG
Germany
Practical system push fittings with safe and innovative lock function from copper alloys for use in a system with SANHA MultiFit®-Flex and MultiFit®-PEX multi layer plastic tubes for hygienic drinking water and reliable heating installations. Due to their sophisticated construction, SANHA system push fittings offer an especially safe and durable connection and are just as tight as press fittings. The push connection is easy to make and has the distinct advantage that no tools are required. In this way, using 3fit®-Push fittings incurs no cost for buying, repairing or maintenance of press machines. 3fit®-Push system fittings are ideally suited in narrow spaces where it might be difficult to press fittings with jaws or slings such as during the renovation of buildings.
Request for a quoteResults for
Tube plastics - Import exportNumber of results
38 Products