Stainless steel bearing - Import export

Sturdy and practical linear rails with radial ball bearing sliders. The X-Rail is a family of linear guides with radial ball bearing sliders for applications requiring cost efficiency and high resistance to corrosion. The linear guides with shaped raceways and the linear guides with flat raceways are available in stainless steel or galvanised or nitrided metal sheeting. With the T + U configuration, the X-Rail system can compensate for any axial misalignment in parallelism of the mounting surfaces.

Sturdy and practical galvanized or stainless steel linear rails with radial ball bearing sliders. The X-Rail is a family of linear guides with radial ball bearing sliders for applications requiring cost efficiency and high resistance to corrosion. The shaped raceway rail, the flat raceway rail and the telescopic rail are available in stainless steel or galvanized sheet metal. With the T + U configuration, the X-Rail system can compensate for any axial misalignment in parallelism of the mounting surfaces. Three rail width sizes: 20mm, 30mm and 45mm Standard rail lengths up to 3,120mm; different lengths upon request Low coefficient of friction Combination of T and U rails for self-aligning bearing applications Easily adjustable slider preload Polymer based wipers available for added roller bearing protection (available on for the thin body style slider) High temperature resistance up to 120°C/250°F The stainless steel X-Rail linear guide version is corrosion resistant, and ensures...

DOF* rotating Can only be used as the first joint in a system. Material: robolink® joint: Fine polyamide PA 2200 Screws: stainless steel VA Ropes:Dyneema Bearing: Alu HC(alternative iglidur® J) *degree of freedom Balls: DOF* rotating Can only be used as the first joint in a system. Material: robolink® joint: Fine polyamide PA 2200 Screws: stainless steel VA Ropes:Dyneema Bearing: Alu HC(alternative iglidur® J) *degree of freedom Balls:

Oscillatory robolink® joint - optional with angle sensors material: robolink® joint: Fine polyamide PA 2200 Screws: stainless steel VA Ropes:Dyneema Bearing: Alu HC(alternative iglidur® J) Balls: Oscillatory robolink® joint - optional with angle sensors material: robolink® joint: Fine polyamide PA 2200 Screws: stainless steel VA Ropes:Dyneema Bearing: Alu HC(alternative iglidur® J) Balls:

drylin® SHT-12 linear module, drylin® R hard-anodised aluminium shafts, Trapezoidal lead screw TR10x2 made of stainless steel with ball bearings, machined lead screw ends 6h9x17mm, quad blocks, aluminium shaft end support, stroke lengths in 250mm or 500mm. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

DryLin® R shafts and supported shafts - Technical data DryLin® R - AWMP Precision aluminum shaft, mm DryLin® R - AWMP DryLin® R - AWMU Supported aluminum shaft, mm DryLin® R - AWMU DryLin® R - SWM/EWM An steel or stainless steel precision shaft, mm DryLin® R - SWM/EWM DryLin® R - SWUM/EWUM Supported steel shaft orstainless steel shaft, mm DryLin® R - SWUM/EWUM DryLin® R - SWUMN/EWUMN Low supported steel shaft orstainless steel shaft, mm DryLin® R - SWUMN/EWUMN DryLin® R - EWUM Partially supported stainless steel shaft, mm DryLin® R - EWUM-Ø DryLin® R - CWM Carbon-fiber shaft, mm DryLin® R - CWM DryLin® R - AWMP Precision aluminum shaft, mm DryLin® R - AWMP DryLin® R - AWMU Supported aluminum shaft, mm DryLin® R - AWMU DryLin® R - SWM/EWM An steel or stainless steel precision shaft, mm DryLin® R - SWM/EWM DryLin® R - SWUM/EWUM Supported steel shaft orstainless steel shaft, mm DryLin® R - SWUM/EWUM DryLin® R - SWUMN/EWUMN Low supported steel shaft orstainless steel shaft, mm DryLin® R - SWUMN/EWUMN DryLin® R - EWUM Partially supported stainless steel shaft, mm DryLin® R - EWUM-Ø DryLin® R - CWM Carbon-fiber shaft, mm DryLin® R - CWM Aluminum Low weight Lower wear of the plain bearing Corrosion resistant Ideal in combination with liners made of iglidur® J/J 200 Delivered off the shelf Steel Low-priced standard High load capacity Application in dry area Hard chrome-plated also available Lower coefficient of friction against plastic bearing Stainless steel High corrosion-resistance High resistance to chemicals Ideal solution for the wet area V4A for extreme chemical intensive applications Female thread, axial male thread Pins Groove cut-in Spanner flat Female thread, radial Special machining All shafts can be individually machined. Please send us your drawing. We'll submit an offer to you in a short time. Shaft request

xiros® B180 FDA for the food sector B180 is already the most successful range in the xiros® family, reliable and inexpensive. Now this range becomes a low-cost solution for the food industry. All dimensions up to Ø 25 mm are also available from now on in the FDA-approved version. For this, it is enough to adapt the cage of the polymer ball bearing, as the rings are already made from FDA-compliant material. Now xirodur® B180 ball bearings with stainless steel balls can be used anywhere in the unpackaged food processing/handling area and where temperatures do not exceed 80°C. Raceways and cages made ​​of FDA approved plastics Lubricant- and maintenance-free Washable For temperatures up to 80℃ Application areas:Food and packaging technology, handling technology, medical technology, cleanroom sector. xiros® B180 FDA for the food sector B180 is already the most successful range in the xiros® family, reliable and inexpensive. Now this range becomes a low-cost solution for the food industry. All dimensions up to Ø 25 mm are also available from now on in the FDA-approved version. For this, it is enough to adapt the cage of the polymer ball bearing, as the rings are already made from FDA-compliant material. Now xirodur® B180 ball bearings with stainless steel balls can be used anywhere in the unpackaged food processing/handling area and where temperatures do not exceed 80°C. Raceways and cages made ​​of FDA approved plastics Lubricant- and maintenance-free Washable For temperatures up to 80℃ Application areas:Food and packaging technology, handling technology, medical technology, cleanroom sector.

Attach this roller glider, which is made of highly-durable aluminium material, permanently to a traversable, overhead lifeline system (8 or 6 mm). Thanks to its special ball bearing-mounted stainless steel rollers, this glider runs really smoothly along the cable and can also be used to go around curves (up to 180°). General national technical approval (German: "abZ"): Z-14.9-786 EN 795:2012, C Ideal for overhead usage Made of highly-durable aluminium material Extremely smooth-running stainless steel rollers Specially designed for lifeline systems (8 and 6 mm)

The incremental encoder with the model designation FOI records the angular position by means of a magnetic sensor and signal processing and generates the corresponding pulse outputs. The robust steel housing with anti-corrosion coating and stainless steel flange (AIMgSi1) ensures versatile use of the incremental encoder for your individual application. The shaft of the FOI is made of stainless steel and the bearings are equipped with a shaft sealing ring.

Recording of the angular position and revolutions by mens of Hall sensors - multiturn version with absolute transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via Profibus-DP. Robust housing manufactured from seawater-proof aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal - sensor circuit consisting of ASIC with Hall elements - electrical connections via the connecting cap with threaded cable connections. The absolute encoders are designed for direct connection to the PROFIBUS-DP. The interface is implemented with the SPC3 Siemens PROFIBUS controller. The protocol corresponds to DP-Slave Class 2 functionality in accordance with Profibus profile for encoders, No. 3.062, and is described in detail in the TRD 12770 user manual. The TRD is mechanicallly and electrically compatible with the electro-optical encoder CRD.

Robust case with wall thickness of 5 mm either in seawater resistant aluminum or in stainless steel - shaft and ball bearings in stainless steel - rotating components with permanent magnet in front chamber - electronic circuit with ASiC and Hall elements and interface components fitted within main chamber, separated from rotating components by a metallic wall - optional potting against water jets (IP 69K) - electrical connections via round plug or lead exit.

Robust aluminium or stainless steel housing (wall thicknesses up to 5 mm) - stainless steel shaft and ball bearing - ball bearing with Simmer ring, rotor with shaft and permanent magnet mounted in pre-chamber - sensor circuit consisting of ASIC with Hall elements and interface electronics in enclosed main chamber - housing protection type IP 69K additionally cast - electrical connection via cable (open cable ends).

Recording of the angular position and revolutions by means of Hall sensors - multiturn version with absolute transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via Profibus-DP. Robust housing manufactured from seawater-proof aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal - sensor circuit consisting of ASIC with Hall elements - electrical connections via the connecting cap with threaded cable connections. The absolute encoders are designed for direct connection to the PROFIBUS-DP. The interface is implemented with the SPC3 Siemens PROFIBUS controller. The protocol corresponds to DP-Slave Class 2 functionality in accordance with Profibus profile for encoders, No. 3.062, and is described in detail in the TRD 12770 user manual. The TRD is mechanicallly and electrically compatible with the electro-optical encoder CRD.

Robust aluminium or stainless steel housing (wall thicknesses up to 5 mm) - stainless steel shaft and ball bearing - ball bearing with Simmer ring, rotor with shaft and permanent magnet mounted in pre-chamber - sensor circuit consisting of ASIC with Hall elements and interface electronics in enclosed main chamber - housing protection type IP 69K additionally cast - electrical connection via cable (open cable ends).

Angle position measurement by means of Hall sensors and signal processing including generation of the analogue output signal. Robust brass housing – stainless steel shaft with sliding bearing – sensor circuit consisting of ASIC with Hall elements – electrical connection via connector.

Recording of the angular position and revolutions by means of Hall sensors - absolute multiturn transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via EtherCAT. Robust housing manufactured from seawater-resistant aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal-sensor circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. In the model series TRK absolute encoders, the EtherCAT interface is integrated according to IEC 61158-2 to 6 and encoder profile CiA DSP406. To achieve the SIL2 level, the TRK/S3 contains a redundant sensor system and additional internal monitoring mechanisms as well as safe communication via the FSoE (failsave over EtherCAT) protocol. The FSoE protocol is implemented according to the Safety over EtherCAT specification ETG.5100 version 1.2.0.

Robust aluminium or stainless steel housing (wall thicknesses up to 5 mm) - stainless steel shaft and ball bearing - ball bearing with Simmer ring, rotor with shaft and permanent magnet mounted in pre-chamber - sensor circuit consisting of ASIC with Hall elements and interface electronics in enclosed main chamber - housing protection type IP 69K additionally cast - electrical connection via cable (open cable ends).

Robust case with wall thickness of 5 mm either in seawater resistant aluminum or in stainless steel - shaft and ball bearings in stainless steel - rotating components with permanent magnet in front chamber - electronic circuit with ASiC and Hall elements and interface components fitted within main chamber, separated from rotating components by a metallic wall - optional potting against water jets (IP 69K) - electrical connections via round plug or lead exit.

Recording of the angular position and revolutions by means of Hall sensors - multiturn version with absolute multiturn transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via PROFINET. Robust housing manufactured from seawater-resistant aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal-sensor circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. The Profinet interface according to IEC 61158 / 61784 or PNO specifications order No. 2.712 and 2.722, version 2.2, is integrated into the model series TRT absolute encoders. Real time classes 1 - 3 are supported, i.e. Real Time (RT) and Isochronous Real Time (IRT) plus the requirements of conformance class C. Setting the address, baud rate or terminating resistances is not necessary. A name, which is stored in the absolute encoder's non-volatile memory, is assigned via the PROFINET controller to address the device.

Recording of the angular position and revolutions by means of Hall sensors - data output plus parameterisation and diagnosis via PROFINET. Robust housing manufactured from seawater-resistant aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal-sensor circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. The Profinet interface according to IEC 61158 / 61784 or PNO specifications order No. 2.712 and 2.722, version 2.2, is integrated into the model series TRT absolute encoders. Real time classes 1 and 3 are supported, i.e. Real Time (RT) and Isochronous Real Time (IRT) plus the requirements of conformance class C. To achieve the SIL2 level, the TRT/S3 contains addtitional internal monitoring mechanisms as well as safe communication via PROFIsafe. The PROFIsafe protocol is implemented according to the PROFIisafe Profile for Safety Technologie version 2.4 (PNO Order No. 3.192)

The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The high temperature model is without shaft seal. Under the rear cover, there is a signal path switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.

The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The model for high temperature use is without shaft seal. Under the rear cover there is a signal changeover switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.

Recording of the angular position and revolutions by means of Hall sensors - absolute multiturn transmission for up to 4096 revolutions - data output plus parameterisation and diagnosis via EtherCAT. Robust housing (housing sickness 5 mm) manufactured from seawater-resistant aluminium (AlMgSi1) or stainless steel - stainless steel shaft - ball bearing with shaft seal - sensors circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. In the model series TRK absolute encoders, the EtherCAT interface is integrated according to IEC 61158-2 to 6 and encoder profile CiA DSP406. As a "full slave", the TRK supports all EtherCAT addressing modes such as logical addressing, position addressing and node addressing. Use of the CANopen over EtherCAT message and the CANopen encoder profile enable parameter and diagnostic data handling as familiar from CANopen. These are contained in an object directory under the same indices as in the case of CANopen.

Our KIS hybrid bearings combine the best of two worlds - the robustness of classic rolling bearings (or stainless steel bearings) and the efficiency of state-of-the-art materials. With an optimised combination of high-quality steel rings and precise ceramic balls, our hybrid bearings offer outstanding strength and durability. Rolling elements made of ceramic offer a current-insulating property. These hybrid bearings have the same dimensions as comparable all-steel bearings and can significantly improve the reliability and robustness of machinery and equipment. In particular, they show their advantages in applications where the bearings are confronted with contamination from abrasive particles, insufficient lubrication, vibrations or current passage. At KIS, we optimise our materials for hybrid bearings to ensure flawless performance in applications under critical conditions at all times.

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® Bend 30° with plain ends

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan® pipe Bend 90° female/male

The piping system consists of high-grade NiroSan® press fittings with an EPDM (=ethylene propylene dien rubber) moulded sealing ring and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® press system and its components are certified in accordance with the rules and regulations of all important European certification bodies. NiroSan-ECO pipe 6 m rods

The installation system consists of high-quality NiroSan® Gas press fittings with yellow moulded sealing rings made of HNBR (hydrogenated nitrile butadiene rubber) and NiroSan® stainless steel system pipes according to EN 10312, DVGW-Arbeitsblatt GW 541 and EN 10312. All NiroSan® Gas press fittings are made of the material 1.4404 / AISI 316L (for moulded fittings) and 1.4408 (for threaded fittings and stainless steel precision castings). The material contains at a minimum of 2.3 % molybdenum and a lower carbon content than the conventional steel quality 316. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® Gas press system is certified in accordance with and all important European certification bodies.

The premium installation system consists of high-grade NiroSan®-Industry press fittings with a red moulded sealing ring made from FKM (fluoro and perfluoro elastomers) for temperatures of up to 200 °C and NiroSan® stainless steel system pipes according to EN 10312. All NiroSan® Industry press fittings are made from the premium stainless steel type 1.4404 / AISI 316L (for pressing components) and 1.4408 (for precision cast threaded stainless steel components). The material 1.4404 contains at least 2.3 % molybdenum, yet less carbon than the conventional type 1.4401. Thereby these materials are not only of equal value but in addition, material 1.4404 / 316L stands out on account of its considerably higher corrosion resistance. The NiroSan® Industry press system and its components are certified in accordance with the rules and regulations of all important British and Continental certification bodies.