Results for
IGUS® GMBH
Germany
iglidur® JATM, metric d1 [mm]: iglidur® JATM/VATM consists of a hard-anodized ring and a bearing ring made of iglidur® J (JATM) and iglidur® V400 (VATM). These glide pairings fetch low coefficients of friction and high wear resistance - without lubrication. Special features Maintenance-free plain bearing system For high service performances High stiffening Simple installation Material: iglidur® J High temperature options VATM, iglidur® V400 More dimensions and supplies on request When to use it? When an axial bearing system with defined gliding partners is desired When extremely high wear resistance is required When a very low coefficient of friction is desired When not to use it? When an additional angle compensation is required igubal® axial bearing When little mounting space is available iglidur® J When only sporadic movements are present iglidur® G Y = wear [μm/km] Figure 36.1: The diagram shows the influence of load (p in MPa) and speed (v in m/s) on the wear of the axial bearing. Y= Coefficient of friction Figure 36.2: In the test with different speeds (v) and loads (p) the coefficients of friction of the bearing systems were determined (v in m/s, p in MPa). iglidur® JATM, metric d1 [mm]:
Request for a quoteIGUS® GMBH
Germany
iglidur® flange bearing d1 [mm]: With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. When to use iglidur® flange bearings? When you want a screw flanged bearing When a clip bearing solution is not satisfactory as a sheet metal feedthrough When there is a housing with very rough tolerances When the tight fit of a press-fit bearing is not sufficient as an axial securing When not to use them? When an additional angle compensation is required igubal® flange bearing When a screw connection is not possible iglidur® clip bearing When a large guide length is necessary iglidur® G General features With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. The design enables high loads with minimum demand on the precision of the housing. iglidur® maintenance-free flange bearings are available in four materials - iglidur® G, iglidur® J, iglidur® X and iglidur® A180. Thus, with this design, a very wide range of applications - from the universal bearing through the highest wear resistance or temperature resistance (up to +250°C) up to FDA-compliant bearing solutions - can be covered. Installation Dependent on the stressing capacities, various mounting types are used. For low radial loads, it is enough to mount the iglidur® flange bearing with just two screws on a surface. For higher radial loads, it is advisable to support the iglidur® flange bearing in a bore on the reinforced side in the load direction. Large tolerances are permitted for this bore, as it is only to additionally support the iglidur® flange bearing. In order to support still higher radial loads, the iglidur® flange bearing can be press-fitted with the longer side in an H tolerance bore. The additional screw connection secures the firm seating of the bearing in the housing. For the mounting of the iglidur® maintenance-free flange bearing, no special tools or devices are necessary. The alignment of the bearing in multiple mounted shafts is easily possible at the installation. Available materials: iglidur® G, iglidur® A180, iglidur® J and iglidur® X The mounting of the iglidur® flange bearing: Simple and safe iglidur® flange bearing d1 [mm]:
Request for a quoteIGUS® GMBH
Germany
MDM Double flange bearing b1 [mm]: When to use it? When the axial safety of the iglidur® clip bearing is not sufficient When there is a housing with very rough tolerance When high axial forces must be absorbed When not to use it? When an automated assembly is required iglidur® MKM When the iglidur® clip bearings offer adequate tightness iglidur® clip bearing When a large guide length is necessary iglidur® MKM MDM Double flange bearing b1 [mm]: Special features Large flange surfaces Symmetrical flange Easy installation Easy to clip on Undetachable after cataphoretic painting process Special option possible
Request for a quoteIGUS® GMBH
Germany
Special features press fit Both sides axially mounted Tolerance compensation of the sheet thickness Easy installation Axially prestressed Special option possible MKM Double flange bearing d1 [mm]: Special features press fit Both sides axially mounted Tolerance compensation of the sheet thickness Easy installation Axially prestressed Special option possible Press in, flange, finished: loss secure, axially mounted When to use it? When a flanged bearing is needed When the housing bore is more than 4 mm long When the axial safety is not ensured by press fit When a two-side flange is required as a thrust surface When not to use it? When maximum compressive strengths are required iglidur® G When a simple press-in bearing is needed iglidur® M250 When a clip-on sheet metal feedthrough is sought iglidur® G MKM Double flange bearing d1 [mm]:
Request for a quoteIGUS® GMBH
Germany
iglidur® L250: For fast rotations Bearings for fast rotary motions like, for instance, in fans and small motors. iglidur® L250 is available as cylindrical bearings and plain bearings with flange. specially developed for fast rotating applications Very low coefficients of friction Excellent wear resistance
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
IGUS® GMBH
Germany
igubal® spherical balls W..M/I Standard spherical ball - dimensional series K and E in metric and inch dimensions igubal® spherical balls W..M/I igubal® spherical balls R...M Low cost spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls R...M igubal® spherical balls X...M Spherical ball for high temperatures - dimensional series K and E in metric dimensions igubal® spherical balls X...M igubal® spherical balls J...M, mm Spherical ball for low humidity absorption - dimensional series K and E in metric dimensions igubal® spherical balls J...M, mm igubal® spherical balls J...M, large dimensions, mm Spherical ball for low humidity absorption - dimensional series K in metric dimensions igubal® spherical balls J...M, large dimensions, mm igubal® spherical balls JKM-GT split, mm Splitted spherical ball for low moisture absorption - Dimensional series K in metric dimensions igubal® spherical balls JKM-GT split, mm igubal® spherical balls UWEM Spherical ball for underwater applications - dimensional series E in metric dimensions igubal® spherical balls UWEM igubal® clearance-free balls J4VEM, mm Clearance-free spherical balls through camber, dimensional series E igubal® clearance-free balls J4VEM, mm igubal® spherical balls J4...M, mm Low priced spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls J4...M, mm igubal®-spherical balls RN248..M, mm Detectable spherical ball - dimensional series K and E in metric dimensions igubal®-spherical balls RN248..M, mm Every iglidur® material possesses a series of special properties which account for its suitability for certain applications and requirements. Currently we offer you spherical balls made of iglidur® materials W300 (standard), J, J4, R, UW and X. igubal® spherical bearings application examples Special properties: maintenance-free dry operation Corrosion resistant High compressive strength High elasticity Very low weight Various materials Spherical balls - material properties iglidur® W300 (Standard) – very wear-resistant material iglidur® R cost-efficient and low coefficients of friction iglidur® X resistant to temperature and chemicals iglidur® J low coefficients of friction and low humidity absorption iglidur® UW suited for underwater applications Tolerances Maintenance-free igubal® spherical balls are designed with a tolerance in the inner diameter according to E10. The shaft should have a tolerance between h6 and h9. When to use it? When maintenance-free materials are required When components of the dimensional series E and K should be used When different iglidur® materials should be tested When high compressive strength is required When high elasticity is required When not to use? When temperatures above +250°C prevail When dimensions over 50 mm are needed When rotation speeds in excess of 0,5 m/s should be implemented igubal® spherical balls W..M/I Standard spherical ball - dimensional series K and E in metric and inch dimensions igubal® spherical balls W..M/I igubal® spherical balls R...M Low cost spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls R...M igubal® spherical balls X...M Spherical ball for high temperatures - dimensional series K and E in metric dimensions igubal® spherical balls X...M igubal® spherical balls J...M, mm Spherical ball for low humidity absorption - dimensional series K and E in metric dimensions igubal® spherical balls J...M, mm igubal® spherical balls J...M, large dimensions, mm Spherical ball for low humidity absorption - dimensional series K in metric dimensions igubal® spherical balls J...M, large dimensions, mm igubal® spherical balls JKM-GT split, mm Splitted spherical ball for low moisture absorption - Dimensional series K in metric dimensions igubal® spherical balls JKM-GT split, mm igubal® spherical balls UWEM Spherical ball for underwater applications - dimensional series E in metric dimensions igubal® spherical balls UWEM igubal® clearance-free balls J4VEM, mm Clearance-free spherical balls through camber, dimensional series E igubal® clearance-free balls J4VEM, mm igubal® spherical balls J4...M, mm Low priced spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls J4...M, mm igubal®-spherical balls RN248..M, mm Detectable spherical ball - dimensional series K and E in metric dimensions igubal®-spherical balls RN248..M, mm
Request for a quoteResults for
Special bearings - Import exportNumber of results
7 ProductsCompany type
Category