Pneumatic cylinder - Import export

easy adjustment for different stock widths and lubricants lubricant dispensation from the inside thru hollow axles – for an even spread series RB SF SW top roll adjustment with pneumatic cylinder

1. NBR shaft seals on hardened cylinder barrels Drum motors axles are usually manufactured from ST37. Commercially available seals rotate directly on the axles. The result, at some point in time, is grooves on the axle. In addition of course oil leaks. This is not the case with the FTK Förderband Technik Kilian pulley motors all drum motors are equipped with hardened and polished cylinder barrels made of stainless steel 316. 2. Oil loss is not a problem for us! Oil change after 50,000 hours of work. Today, for reasons of cost, fewer and fewer users concern themselves with plant maintenance. The maintenance of complex plants is mainly carried out by outside specialists. Simple prefabricated parts, however, are usually used till worn out. This is also the case with drum motors. We have made allowance for this behaviour. The FTK Förderband Technik Kilian drum motors only require an oil change after 50,000 hours of work. In the case of operation with 3 shifts for example

Linear units with a belt drive specifically dedicated to the use along the Z axis. The Modline Z family includes axes with pneumatic compensation of the load. The section integrates the pneumatic cylinder and encloses the passage of cables. It requires smaller motors, offering increased performances with savings in cost and energy. Our products stand out for their: high quality and competitive performances no play transmissions achieved by high torque couplings beams with transversal stiffening ribs and preset for threads on profile ends accurate scaling with reduced maintenance the most complete range of accessories

Magnetic field sensors are used in particular for contactless detection of the piston position in pneumatic cylinders. Using a patented operating principle, our magnetic field sensors detect permanent magnets of different strength attached to the piston in all common cylinders error-free. The sensors operate wear-free, are short-circuit proof, rugged and IP67 rated. We also offer solutions for use in welding or hazardous areas as well as for analog queries.

igubal® clevis joint, mm With and without pin and circlip igubal® clevis joint, mm igubal® clevis joints with spring loaded pins, mm igubal® clevis joints with spring loaded pins, mm igubal® clevis joint combination, mm Complete knee joints consisting of clevis joint and rod end bearing igubal® clevis joint combination, mm igubal® spring loaded pin, mm igubal® spring loaded pin, mm igubal® pin, mm GBM/GSR Pin and circlip igubal® pin, mm GBM/GSR igubal® clevis joint, detectable, mm igubal® clevis joint, detectable, mm igubal® clevis joints with spring loaded pins, detectable, mm igubal® clevis joints with spring loaded pins, detectable, mm igubal® spring loaded pin, detectable, mm igubal® spring loaded pin, detectable, mm Most important features: Very low weight High tensile forces Combinable with rod end bearings of the dimensional series E vibration dampening Noise dampening Available for left-hand and right-hand threads igubal® clevis joints are solid polymer made of igumid G according to DIN 71752, which can be combined with the rod end bearings of the dimensional series E as counterpiece. They consist of clevis joint, pin and circlip, or alternatively with spring loaded pin. igubal® spherical bearings application examples When to use it? When high stiffening is required When freedom from corrosion is desired When lubrication should not be used When you want to save weight When maintenance-free dry operation is desired When the easiest installation should be implemented When combinations with pneumatic cylinders and gas struts should be implemented When not to use? When temperatures above +200°C prevail When dimensions over 20 mm are needed igubal® clevis joint, mm With and without pin and circlip igubal® clevis joint, mm igubal® clevis joints with spring loaded pins, mm igubal® clevis joints with spring loaded pins, mm igubal® clevis joint combination, mm Complete knee joints consisting of clevis joint and rod end bearing igubal® clevis joint combination, mm igubal® spring loaded pin, mm igubal® spring loaded pin, mm igubal® pin, mm GBM/GSR Pin and circlip igubal® pin, mm GBM/GSR igubal® clevis joint, detectable, mm igubal® clevis joint, detectable, mm igubal® clevis joints with spring loaded pins, detectable, mm igubal® clevis joints with spring loaded pins, detectable, mm igubal® spring loaded pin, detectable, mm igubal® spring loaded pin, detectable, mm

igubal® rod end bearing, female thread With female thread in metric and inch dimensions igubal® rod end bearing, female thread igubal® rod end bearing, male thread With male thread in metric and inch dimensions igubal® rod end bearing, male thread igubal® rod end bearing CL For simplified mounting, with inner and outer threads in metric dimensions igubal® rod end bearing CL igubal® rod End Bearing CL DT For simplified installation, detectable with female thread in metric dimensions igubal® rod End Bearing CL DT igubal® fitting screw, mm Fitting screw with circlip igubal® fitting screw, mm When to use it? When you want to save weight When rotating, oscillating and linear movements should be implemented When high-frequency oscillations/vibrations predominate When a low-noise operation is desired When an electrically insulating part is required When freedom from corrosion is desired For combinations with pneumatic cylinders and gas struts When chemical resistance is required When high stiffening is required When not to use? When you have temperatures above +80°C (then HT options) When rotation speeds in excess of 0.5 m/s should be implemented When very high tensile and lateral loads prevail When applications should be implemented with hydraulic cylinder When dimensions over 30 mm are needed igubal® rod end bearing, female thread With female thread in metric and inch dimensions igubal® rod end bearing, female thread igubal® rod end bearing, male thread With male thread in metric and inch dimensions igubal® rod end bearing, male thread igubal® rod end bearing CL For simplified mounting, with inner and outer threads in metric dimensions igubal® rod end bearing CL igubal® rod End Bearing CL DT For simplified installation, detectable with female thread in metric dimensions igubal® rod End Bearing CL DT igubal® fitting screw, mm Fitting screw with circlip igubal® fitting screw, mm Special properties of the igubal® rod end bearings Maintenance-free, self lubricating High stiffening Very high fatigue strength in varying loads Compensation for alignment errors Compensation of edge loads Insensitive to dirt, dust and lint balls Resistant to corrosion and chemicals High dampening qualities Suitable for rotary, oscillating and linear movements Very low weight Dimensional series K and E, dimensions according to DIN ISO 12240 Version with metal sleeve in the spherical ball for enhanced torque Tolerances igubal rod end bearings can be used, according to the application, with different tolerances. They are designed with a large clearance in the standard product, which enables a secure operation even under high peripheral speeds. The bore of the inner ring has a tolerance according to E10. The shafts should have a tolerance between h6 and h9. Please contact us in case you require lower or more bearing tolerances. Loads igubal® rod end bearings take high forces in normal ambient temperatures, have excellent dampening properties and weigh only a fifth of the conventional metallic bearing housing. In particular cases the load carrying capacity of the rod end bearings should be checked in a practical trial especially with high constant loads and at higher temperatures. Coefficients of surface friction and speeds Rotary motions of the mounted shaft take place directly in the bearing ball made of iglidur® W300. The advantage of this plastic/steel plain bearing is that high speeds can be achieved in dry operation. Taking the radial loads into account, maximum surface speeds up to 0.5 m/s rotating can be attained. The maintenance-free igubal® rod end bearings casually permit linear and oscillating movements of the shaft. Delivery program igubal® rod end bearings are available in the dimensional series K and E for shaft diameters of 2 to 30 mm in all dimensions according to DIN ISO 12240, and of course respectively in the Form A - with male thread and Form B - with female thread The dimensional series K and partly E are moreover available in inch dimensions and – as special version – with a stainless steel sleeve in the spherical ball. Thereby an essentially higher tightening torque is possible than with the plastic spherical ball. Please ask us for other sizes. igubal® rod end bearings - Applications igubal® rod end bearings - Applications Temperatures Dimensional series K in A+B variants for temperatures upt to +200°C (HAT material).

Electric cylinders are self-locking. So they do not need energy when they stand still. This makes the electric cylinders to be an interesting alternative to pneumatic and hydraulic actuators. Powerful DC motors, signal lines, potentiometers and Hall-ICs for position indication, as well as integrated end switches uncomplicatedly serve for meeting the most frequent requirements.

The completely equipped electrical cylinder unit includes the motor transmission unit, along with the motor brake, two-channel Hall-IC sensor and two end-limit switches. All connection lines run directly out of the unit to make configuration and initial start-up easier, particularly for PLC operation. The fixation of the electric cylinder connections is compatible with commercial pneumatic and hydraulic cylinders.

Self-Compensating, Rolling Diaphragm Technology Energy capacity 20 Nm/cycle Stroke 12 mm Tried-and-tested and durable: Due to a hermetically sealed rolling diaphragm in each absorber, the MC150 to MC600 product family is suitable for an exceptional high lifetime of use with up to 25 million cycles. The rolling diaphragm technology perfected by ACE ensures complete separation of the damping fluid from the surrounding air. This makes direct installation in a pressure chamber e.g. as end stop damping in pneumatic cylinders up to approx. 7 bar possible. The rolling diaphragm also benefits the very low return forces of these maintenance-free, ready-to-install absorbers. Progressive energy capacities, with a wide range of effective weight potential make these miniature shock absorbers, complete with an integrated positive stop a winner. Furthermore, the use of a side load adapter allows impact angles of up to 25°. Miniature shock absorbers capable of universal mounting even inside a...

Self-Compensating, Piston Tube Technology Energy capacity 16 Nm/cycle Stroke 10 mm Soft damping, but enormous capacity: The range of 'soft contact' absorbers SC²25 to 190 extends from thread size M10 to M14 and covers effective weight ranges of 1 kg to 1,550 kg. All models are characterised by high energy absorption and they also unite the piston tube technology with the diaphragm seal perfected by ACE. This enables direct installation as end position damping in pneumatic cylinders at 5 to 7 bar or applications where deceleration needs to take placed close to the pivot point. They are maintenance-free, have an integrated positive stop and are mountable in any position. The option of a side load adapter allows impact angles of up to 25°. Thanks to their robust design and their durability, these miniature shock absorbers can be used for a wide range of applications. Designers mainly use them for pick and place systems, pneumatic rotary modules and in automation applications.

Self-Compensating, Piston Tube Technology Energy capacity 10 Nm/cycle Stroke 8 mm Soft damping, but enormous capacity: The range of 'soft contact' absorbers SC²25 to 190 extends from thread size M10 to M14 and covers effective weight ranges of 1 kg to 1,550 kg. All models are characterised by high energy absorption and they also unite the piston tube technology with the diaphragm seal perfected by ACE. This enables direct installation as end position damping in pneumatic cylinders at 5 to 7 bar or applications where deceleration needs to take placed close to the pivot point. They are maintenance-free, have an integrated positive stop and are mountable in any position. The option of a side load adapter allows impact angles of up to 25°. Thanks to their robust design and their durability, these miniature shock absorbers can be used for a wide range of applications. Designers mainly use them for pick and place systems, pneumatic rotary modules and in automation applications.

Self-Compensating, Rolling Diaphragm Technology Energy capacity 41 Nm/cycle Stroke 12 mm Tried-and-tested and durable: Due to a hermetically sealed rolling diaphragm in each absorber, the MC150 to MC600 product family is suitable for an exceptional high lifetime of use with up to 25 million cycles. The rolling diaphragm technology perfected by ACE ensures complete separation of the damping fluid from the surrounding air. This makes direct installation in a pressure chamber e.g. as end stop damping in pneumatic cylinders up to approx. 7 bar possible. The rolling diaphragm also benefits the very low return forces of these maintenance-free, ready-to-install absorbers. Progressive energy capacities, with a wide range of effective weight potential make these miniature shock absorbers, complete with an integrated positive stop a winner. Furthermore, the use of a side load adapter allows impact angles of up to 25°. Miniature shock absorbers capable of universal mounting even inside a...

Avola GAMA 65 V revolving cross cut / rip cut saw Equipment / scope of supply- Cutting heights 90° / 245 mm - 45° / 164 mm - 30° / 113 mm - Machine table with lateral movement approx. 400 mm with pneumatic brake system - Machine hood with lateral PVC protective curtains - pneumatic clamping cylinder left - right - pneumatic cross-cutting operation using two-hand control - electrical saw blade inclination 90 – 30° - Revolving table 0 - 270° - Laser light for cross-cutting - Saw bla de height adjustment via mechanical stop system with scale - TCT saw blade 650 mm, dust extraction spigots 160 / 125 mm - Drive motor 12 kW – direct motor speed 1/min – 3,000 - Saw blade speed 1/min – 3,000

Self-Compensating, Rolling Diaphragm Technology Energy capacity 136 Nm/cycle Stroke 25 mm Tried-and-tested and durable: Due to a hermetically sealed rolling diaphragm in each absorber, the MC150 to MC600 product family is suitable for an exceptional high lifetime of use with up to 25 million cycles. The rolling diaphragm technology perfected by ACE ensures complete separation of the damping fluid from the surrounding air. This makes direct installation in a pressure chamber e.g. as end stop damping in pneumatic cylinders up to approx. 7 bar possible. The rolling diaphragm also benefits the very low return forces of these maintenance-free, ready-to-install absorbers. Progressive energy capacities, with a wide range of effective weight potential make these miniature shock absorbers, complete with an integrated positive stop a winner. Furthermore, the use of a side load adapter allows impact angles of up to 25°. Miniature shock absorbers capable of universal mounting even inside a...

Avola GAMA 80 V carpenter’s circular saw bench for professional applications Equipment / scope of supply- Motor rating 22 kW (P1) / 400 Vac-50 Hz star delta start gear drive - Motor speed rpm 3.000 / sawblade speed rpm 2.200 - Cutting height 90° / 310 mm – 45° / 217 mm – 30° / 149 mm - Electrical sawblade inclination 90 – 30° - Revolving table 0-270° - Machine table with lateral movement 650 mm - Automatic vertical pneumatic clamping cylinders right / left - Laser light for cross cutting - TCT-sawblade, 800 x 30 x T90 - Dust extraction spigots 160 / 160 / 80 / 80 mm - Sawblade height adjustment via mechanical stop system, with measuring scale, easy to adjust - DUO infeed / outfeed devices

Pressure belt filters are used for cleaning contaminated cutting fluids in metal processing and rolling mill applications. Cleaned cutting fluids have longer lifespan, improve surface quality, and contribute to heat dissipation at the processing or forming point. Advantages: High throughput capacity No backwashing during regeneration Easy discharge of filter cake Short regeneration time Compatible with various plastic filter belts High and low-pressure rinsing system Affordable price Operation: The F.E.S. pressure belt filter addresses the need for filtration without disposal issues by utilizing a standard feature of a circulating plastic filter belt. A filter belt cleaning device is integrated into the head section of the belt filter. The closing mechanism of the sealing flaps, lowered pneumatic cylinders, and movable protective covers ensure a low height for easy installation and operation.

Hinged belt filters, also known as folding belt filters, are used for cleaning contaminated coolant fluids in metal processing and rolling mill applications. Cleaned coolant fluids have longer service life, improve the surface quality of workpieces or rolled goods, and assist in heat dissipation at the processing or forming site. Advantages: High throughput capacity No backflushing required during regeneration Easy discharge of filter cake Short regeneration time Compatible with various plastic filter belts High and low-pressure flushing system Cost-effective Operation: The F.E.S. hinged belt filter incorporates a circulating plastic filter belt to meet the filtration requirements without disposal issues. A filter belt cleaning device is located below the filtrate discharge chamber. The opening and closing of the chambers are controlled by two pneumatic cylinders. The self-locking toggle lever mechanism keeps the chambers closed even in the event of a loss of compressed air.

The MIXACO discharge stations are used for dust free emptying of the product into the further processing step (e.g. dosing system into an extruder). The container is fixed in place when moved into the discharge station. Two different executions are available: Type Guide fork Type Platform Differentiated by the way of feeding the container. Type Guide fork The movable container is pushed by means of its own wheels into the discharge station type guide fork and is locked in place. A pneumatic coupling is used to connect the discharge pipe to the container discharge valve. Type Platform The container is placed onto the emptying station with the aid of a lifting device (crane or forklift). Equipment Positioning of the container Pneumatic coupling between container and the further production step Pneumatic rotary cylinder for automatic opening / closing of the container discharge valve (0/90°)

For many tasks in the field of automation technology, it is necessary to recognize the motional processes in pneumatic and hydraulic cylinders and to detect the position of the piston with precision. For this, magnetic cylinder sensors are used.

For many tasks in the field of automation technology, it is necessary to recognize the motional processes in pneumatic and hydraulic cylinders and to detect the position of the piston with precision. For this, magnetic cylinder sensors are used.

For many tasks in the field of automation technology, it is necessary to recognize the motional processes in pneumatic and hydraulic cylinders and to detect the position of the piston with precision. For this, magnetic cylinder sensors are used.

Hydraulic Cylinders We specialise in the customer-specific manufacture of single and double-acting hydraulic and pneumatic cylinders. Telescopic cylinders are also part of our production programme. We develop and design cylinders to customers prescribed boundary conditions or manufacture according to customer drawings provided. We develop and design cylinders to customers prescribed boundary conditions or manufacture according to customer drawings provided. Your wishes have priority - from the design to the final inspection:

Our big bag emptying stations are generally designed for big bags with a capacity up to 2 tons. Different alternatives and options are available to meet customer’s requirements. In case of a big bag emptying station for bad flowing products, we can provide a vibrating frame as well as a massaging system with pneumatically operated cylinders to enhance the discharge (or a combination of both systems in the worst case). The design of this station will allways depend of the characteristics of the product which has to be discharged. The big bag emptying station is provided with a lifting frame, adjustable in height, with automatic big bag tension device which allows a completely emptying of the bag. How it works: by loosing weight during emptying, the big bag will be tensioned automatically by a telescoping spring system. Optionally, we offer the possibility to shut even partially filled big bags.