Special bearings - Import export

iglidur® JATM, metric d1 [mm]: iglidur® JATM/VATM consists of a hard-anodized ring and a bearing ring made of iglidur® J (JATM) and iglidur® V400 (VATM). These glide pairings fetch low coefficients of friction and high wear resistance - without lubrication. Special features Maintenance-free plain bearing system For high service performances High stiffening Simple installation Material: iglidur® J High temperature options VATM, iglidur® V400 More dimensions and supplies on request When to use it? When an axial bearing system with defined gliding partners is desired When extremely high wear resistance is required When a very low coefficient of friction is desired When not to use it? When an additional angle compensation is required igubal® axial bearing When little mounting space is available iglidur® J When only sporadic movements are present iglidur® G Y = wear [μm/km] Figure 36.1: The diagram shows the influence of load (p in MPa) and speed (v in m/s) on the wear of the axial bearing. Y= Coefficient of friction Figure 36.2: In the test with different speeds (v) and loads (p) the coefficients of friction of the bearing systems were determined (v in m/s, p in MPa). iglidur® JATM, metric d1 [mm]:

iglidur® flange bearing d1 [mm]: With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. When to use iglidur® flange bearings? When you want a screw flanged bearing When a clip bearing solution is not satisfactory as a sheet metal feedthrough When there is a housing with very rough tolerances When the tight fit of a press-fit bearing is not sufficient as an axial securing When not to use them? When an additional angle compensation is required igubal® flange bearing When a screw connection is not possible iglidur® clip bearing When a large guide length is necessary iglidur® G General features With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. The design enables high loads with minimum demand on the precision of the housing. iglidur® maintenance-free flange bearings are available in four materials - iglidur® G, iglidur® J, iglidur® X and iglidur® A180. Thus, with this design, a very wide range of applications - from the universal bearing through the highest wear resistance or temperature resistance (up to +250°C) up to FDA-compliant bearing solutions - can be covered. Installation Dependent on the stressing capacities, various mounting types are used. For low radial loads, it is enough to mount the iglidur® flange bearing with just two screws on a surface. For higher radial loads, it is advisable to support the iglidur® flange bearing in a bore on the reinforced side in the load direction. Large tolerances are permitted for this bore, as it is only to additionally support the iglidur® flange bearing. In order to support still higher radial loads, the iglidur® flange bearing can be press-fitted with the longer side in an H tolerance bore. The additional screw connection secures the firm seating of the bearing in the housing. For the mounting of the iglidur® maintenance-free flange bearing, no special tools or devices are necessary. The alignment of the bearing in multiple mounted shafts is easily possible at the installation. Available materials: iglidur® G, iglidur® A180, iglidur® J and iglidur® X The mounting of the iglidur® flange bearing: Simple and safe iglidur® flange bearing d1 [mm]:

MDM Double flange bearing b1 [mm]: When to use it? When the axial safety of the iglidur® clip bearing is not sufficient When there is a housing with very rough tolerance When high axial forces must be absorbed When not to use it? When an automated assembly is required iglidur® MKM When the iglidur® clip bearings offer adequate tightness iglidur® clip bearing When a large guide length is necessary iglidur® MKM MDM Double flange bearing b1 [mm]: Special features Large flange surfaces Symmetrical flange Easy installation Easy to clip on Undetachable after cataphoretic painting process Special option possible

Special features press fit Both sides axially mounted Tolerance compensation of the sheet thickness Easy installation Axially prestressed Special option possible MKM Double flange bearing d1 [mm]: Special features press fit Both sides axially mounted Tolerance compensation of the sheet thickness Easy installation Axially prestressed Special option possible Press in, flange, finished: loss secure, axially mounted When to use it? When a flanged bearing is needed When the housing bore is more than 4 mm long When the axial safety is not ensured by press fit When a two-side flange is required as a thrust surface When not to use it? When maximum compressive strengths are required iglidur® G When a simple press-in bearing is needed iglidur® M250 When a clip-on sheet metal feedthrough is sought iglidur® G MKM Double flange bearing d1 [mm]:

iglidur® L250: For fast rotations Bearings for fast rotary motions like, for instance, in fans and small motors. iglidur® L250 is available as cylindrical bearings and plain bearings with flange. specially developed for fast rotating applications Very low coefficients of friction Excellent wear resistance

igubal® spherical balls W..M/I Standard spherical ball - dimensional series K and E in metric and inch dimensions igubal® spherical balls W..M/I igubal® spherical balls R...M Low cost spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls R...M igubal® spherical balls X...M Spherical ball for high temperatures - dimensional series K and E in metric dimensions igubal® spherical balls X...M igubal® spherical balls J...M, mm Spherical ball for low humidity absorption - dimensional series K and E in metric dimensions igubal® spherical balls J...M, mm igubal® spherical balls J...M, large dimensions, mm Spherical ball for low humidity absorption - dimensional series K in metric dimensions igubal® spherical balls J...M, large dimensions, mm igubal® spherical balls JKM-GT split, mm Splitted spherical ball for low moisture absorption - Dimensional series K in metric dimensions igubal® spherical balls JKM-GT split, mm igubal® spherical balls UWEM Spherical ball for underwater applications - dimensional series E in metric dimensions igubal® spherical balls UWEM igubal® clearance-free balls J4VEM, mm Clearance-free spherical balls through camber, dimensional series E igubal® clearance-free balls J4VEM, mm igubal® spherical balls J4...M, mm Low priced spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls J4...M, mm igubal®-spherical balls RN248..M, mm Detectable spherical ball - dimensional series K and E in metric dimensions igubal®-spherical balls RN248..M, mm Every iglidur® material possesses a series of special properties which account for its suitability for certain applications and requirements. Currently we offer you spherical balls made of iglidur® materials W300 (standard), J, J4, R, UW and X. igubal® spherical bearings application examples Special properties: maintenance-free dry operation Corrosion resistant High compressive strength High elasticity Very low weight Various materials Spherical balls - material properties iglidur® W300 (Standard) – very wear-resistant material iglidur® R cost-efficient and low coefficients of friction iglidur® X resistant to temperature and chemicals iglidur® J low coefficients of friction and low humidity absorption iglidur® UW suited for underwater applications Tolerances Maintenance-free igubal® spherical balls are designed with a tolerance in the inner diameter according to E10. The shaft should have a tolerance between h6 and h9. When to use it? When maintenance-free materials are required When components of the dimensional series E and K should be used When different iglidur® materials should be tested When high compressive strength is required When high elasticity is required When not to use? When temperatures above +250°C prevail When dimensions over 50 mm are needed When rotation speeds in excess of 0,5 m/s should be implemented igubal® spherical balls W..M/I Standard spherical ball - dimensional series K and E in metric and inch dimensions igubal® spherical balls W..M/I igubal® spherical balls R...M Low cost spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls R...M igubal® spherical balls X...M Spherical ball for high temperatures - dimensional series K and E in metric dimensions igubal® spherical balls X...M igubal® spherical balls J...M, mm Spherical ball for low humidity absorption - dimensional series K and E in metric dimensions igubal® spherical balls J...M, mm igubal® spherical balls J...M, large dimensions, mm Spherical ball for low humidity absorption - dimensional series K in metric dimensions igubal® spherical balls J...M, large dimensions, mm igubal® spherical balls JKM-GT split, mm Splitted spherical ball for low moisture absorption - Dimensional series K in metric dimensions igubal® spherical balls JKM-GT split, mm igubal® spherical balls UWEM Spherical ball for underwater applications - dimensional series E in metric dimensions igubal® spherical balls UWEM igubal® clearance-free balls J4VEM, mm Clearance-free spherical balls through camber, dimensional series E igubal® clearance-free balls J4VEM, mm igubal® spherical balls J4...M, mm Low priced spherical ball - dimensional series K and E in metric dimensions igubal® spherical balls J4...M, mm igubal®-spherical balls RN248..M, mm Detectable spherical ball - dimensional series K and E in metric dimensions igubal®-spherical balls RN248..M, mm

Special customer requirements occasioned us to produce selected bright steel specialities, such as antifriction bearing steel / ball bearing steel, which we also refer to as precision bright steel. The characteristic features of these antifriction bearing steels/ball bearing steels, etc. include the producible materials, attainable tolerances, achievable surfaces, available bar lengths, and obtainable strengths. Metering rods Ejector pins Fittings Ball bearings/Overrunning clutches >> Current alloy surcharges >> Current scarp surcharges VERSIONS AND FORMS SUPPLIED Drawing From 2.0 mm to 28.0 mm round, tolerance zone IT 9 Min. bar length 2,000 mm Max. bar length 5,000 mm (2.0 mm to 6.0 mm round) Max. bar length 7,000 mm (6.0 mm to 16.0 mm round) Max. bar length 9,000 mm (> 16.0 mm round and on request) Length tolerance ± 25.0 mm Grinding From 0.5 mm to 32.0 mm round, tolerance zone IT 6 (Rm up to 1,600 N/mm² for bright steel for standard parts) > 32.0 mm to 60.0 mm...

Special customer requirements occasioned us to produce selected bright steel specialities, such as antifriction bearing steel / ball bearing steel, which we also refer to as precision bright steel. The characteristic features of these antifriction bearing steels/ball bearing steels, etc. include the producible materials, attainable tolerances, achievable surfaces, available bar lengths, and obtainable strengths. Metering rods Ejector pins Fittings Ball bearings/Overrunning clutches >> Current alloy surcharges >> Current scarp surcharges VERSIONS AND FORMS SUPPLIED Drawing From 2.0 mm to 28.0 mm round, tolerance zone IT 9 Min. bar length 2,000 mm Max. bar length 5,000 mm (2.0 mm to 6.0 mm round) Max. bar length 7,000 mm (6.0 mm to 16.0 mm round) Max. bar length 9,000 mm (> 16.0 mm round and on request) Length tolerance ± 25.0 mm Grinding From 0.5 mm to 32.0 mm round, tolerance zone IT 6 (Rm up to 1,600 N/mm² for bright steel for standard parts) > 32.0 mm to 60.0 mm...

Special customer requirements occasioned us to produce selected bright steel specialities, such as antifriction bearing steel / ball bearing steel, which we also refer to as precision bright steel. The characteristic features of these antifriction bearing steels/ball bearing steels, etc. include the producible materials, attainable tolerances, achievable surfaces, available bar lengths, and obtainable strengths. Metering rods Ejector pins Fittings Ball bearings/Overrunning clutches >> Current alloy surcharges >> Current scarp surcharges VERSIONS AND FORMS SUPPLIED Drawing From 2.0 mm to 28.0 mm round, tolerance zone IT 9 Min. bar length 2,000 mm Max. bar length 5,000 mm (2.0 mm to 6.0 mm round) Max. bar length 7,000 mm (6.0 mm to 16.0 mm round) Max. bar length 9,000 mm (> 16.0 mm round and on request) Length tolerance ± 25.0 mm Grinding From 0.5 mm to 32.0 mm round, tolerance zone IT 6 (Rm up to 1,600 N/mm² for bright steel for standard parts) > 32.0 mm to 60.0 mm...

Pneumatic Rotational Clamping Holding torque 76 Nm Direct clamping on the shaft: Rotation motions are prevented by the ACE models LOCKED R. Their clamping elements are available for shaft diameters of 50 to 340 mm and ensure maximum holding forces. The clamp is immediately applied by the diaphragm and spring-plate system when pressure is lost. Pneumatic quick-switch valves reduce the reaction times. The costs are low in comparison with hydraulic clamping systems. Their performance is, however, achieved or exceeded despite the compact and easy to assemble design. Special versions for YRT bearings as well as active clamping elements are additionally available. ACE recommends the use of the optional shaft flange as wear protection. The clamping force can be increased considerably by the use of the additional air function.

Special customer requirements occasioned us to produce selected bright steel specialities, such as antifriction bearing steel / ball bearing steel, which we also refer to as precision bright steel. The characteristic features of these antifriction bearing steels/ball bearing steels, etc. include the producible materials, attainable tolerances, achievable surfaces, available bar lengths, and obtainable strengths. Metering rods Ejector pins Fittings Ball bearings/Overrunning clutches >> Current alloy surcharges >> Current scarp surcharges VERSIONS AND FORMS SUPPLIED Drawing From 2.0 mm to 28.0 mm round, tolerance zone IT 9 Min. bar length 2,000 mm Max. bar length 5,000 mm (2.0 mm to 6.0 mm round) Max. bar length 7,000 mm (6.0 mm to 16.0 mm round) Max. bar length 9,000 mm (> 16.0 mm round and on request) Length tolerance ± 25.0 mm Grinding From 0.5 mm to 32.0 mm round, tolerance zone IT 6 (Rm up to 1,600 N/mm² for bright steel for standard parts) > 32.0 mm to 60.0 mm...

Attach this roller glider, which is made of highly-durable aluminium material, permanently to a traversable, overhead lifeline system (8 or 6 mm). Thanks to its special ball bearing-mounted stainless steel rollers, this glider runs really smoothly along the cable and can also be used to go around curves (up to 180°). General national technical approval (German: "abZ"): Z-14.9-786 EN 795:2012, C Ideal for overhead usage Made of highly-durable aluminium material Extremely smooth-running stainless steel rollers Specially designed for lifeline systems (8 and 6 mm)

The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The model for high temperature use is without shaft seal. Under the rear cover there is a signal changeover switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.

The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The high temperature model is without shaft seal. Under the rear cover, there is a signal path switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.