Monitoring devices - Import export

Everywhere, where digital signals must be electrically separated and processed or current and voltage limited power supply is needed, our interface devices are used such as isolating switching amplifiers, solenoid drivers, relay couplers and rotation speed monitors. The interface devices are available in the IP20 modular housing for DIN rail as well as in the compact IP67 housing for decentralized remote-site use. The product portfolio also comprises solutions for the Ex area and SIL-certified devices.

We are your reliable partner for the realisation of your products - from the initial idea to series production and beyond. Our goal is to offer you a comprehensive full service and to manufacture your products economically and in the highest quality. We support you in the consultative development of your early concepts and prepare an initial cost estimate in the concept phase. In addition, we accompany you during series and mass production with our long-standing manufacturing partners in the Far East and ensure reliable logistical handling.

CSN ® Explosion proof cartridge heaters as direct heaters for liquids or gases in hazardous environment. These units are equipped with a heating bundle or a replaceable ceramic heating element. For temperature control these heaters are available with an integrated temperature monitoring system. These devices are available in various material grades. The electric cartridge heating element type 93./..EEx….T.(.) is designed for the heating of liquids in the zone 1 and zone 2. The standars elements, mentioned in this list are suitable for DGRL (code 2014/68/EU) Art. 4, Para. 3. The elements can be suited (on request) to other uses requiring another classification according to DGRL Further information about our CSN® ExCartridge Heater

Force-of-gravity separators, which are used as pre-filters or for the separation of large quantities of dust and swarf. Cyclone separator Cyclones are force-of-gravity separators. The separation principle is based on centrifugal force, which is produced by the tangential injection of the raw air. Cyclones are used as pre-filters or for the separation of large quantities of dust and swarf. The degree of separation of a cyclone is not normally sufficient to meet the usual environmental protection requirements. The cyclone exhaust air must be post-filtered in most cases. Product description A cyclone essentially consists of three parts: the intake cylinder, the cone and the immersion tube. In the intake cylinder, the raw air is brought into a circular path by means of tangential injection. Due to the taper of the subsequent cone, the speed of rotation increases sharply, so that the particles are pressed by centrifugal force against the outer wall and decelerated by friction, causing them to drop out of the air stream and fall down. The cleaned air leaves the cone in an upward direction via the central immersion tube. Cyclones are usually welded sheet steel structures. Cellular wheel sluices or, in individual cases, double-gate sluices are used for the pressureless discharge of the material. In order to increase the cyclone effect, or the degree of separation, counter-spirals with a pipe connection can be placed on top of the immersion tube. Further options are, for example, wearing devices, explosion pressure relief devices, control flaps, level monitoring devices and manufacturing in stainless steel or galvanised sheet steel.

The particleboard forming line consists of machines for forming and monitoring the particle mat. Additional devices for quality monitoring complete the function of Siempelkamp’s forming line. The plant modules can be adjusted to the respective requirements thus preparing the mat optimally for its compaction in a ContiRoll®. The equipment is designed to produce board thicknesses between 6 and 40 mm without any problem. A typical particle mat former consists of one or two mechanical mat formers for the core layer and two wind sifters for the top and the rear surfaces. The three-layer particleboard thus produced distinguishes by a homogeneous, core layer consisting of coarse particles and two surface layers, the particle size of which is decreasing from the core to the outer faces.

MDF forming lines consist of machines for forming and monitoring the bre mat. Additional devices for quality monitoring complete the function. The plant modules can be adjusted to the respective requirements thus preparing the mat optimally for its compaction in a ContiRoll®. The equipment is designed to produce board thicknesses between 1.5 and 40 mm without any problem. The forming belt conveyor is a modular design as well tuned to plant output and feasible board formats. Features Forming belt with pneumatic tensioning station as well as electric drive station and integrated automatic reject m Integrated belt scale for controlling the mat former output to ensure consistent product quality Mat moisture meter Automatic edge trimming system ex prepress Monitoring equipment to prevent steel belt damage peak detectors metal detector

The Hub intelligent control panel is a key element of the Ajax security system. The device monitors operation of all Ajax detectors and immediately sends an alarm signal to the owner and the Central Monitoring Station.