Results for
LESJÖFORS INDUSTRIAL SPRINGS & PRESSINGS GMBH
Germany
Typical areas of use for hydraulic gas spring are controlled opening and closing of hatches and hoods. The gas springs can also be adapted to control complete equipment such as ventilation apertures, chairs, beds, windows, tools and machinery.
Request for a quoteFRIEDRICH VOLLMER FEINMESSGERÄTEBAU GMBH
Germany
The high-speed servo-hydraulic control of the mill screwdown closes the loop: The thickness values measured precise to the micrometre form the basis for quick and precise control. Vollmer offers solutions for all control concepts from simple feedback control through to complete mass flow control or Direct gap contol for rolling of wedge-shaped strip and in tandem mills. Vollmer supplies the complete control system – from the sensors through the control technology right up to the hydraulics and the cylinder – from a single source. For our customers that means having just one contact partner – in short: A one-stop solution.
Request for a quoteSHENZHEN PROMOSTAR HARDWARE CO.,LTD
Germany
Valve screw mechanical accessories.
Request for a quoteCARL FRIEDRICH USBECK KG
Germany
outside thread M10 x 1, CE-0085CQ0255
Request for a quoteWOMA GMBH
Germany
The pumps of the 3 series deliver operating pressures up to 250 bar and volumetric flow rates of up to 400 l/min and are the preferred choice in channel and tube cleaning applications.The seal system of this plunger pump is very easy to maintain due to fewer wearing parts. The ceramic plungers used are highly resistant to acid and alkaline liquids.
Request for a quoteWOMA GMBH
Germany
The ARP (Abrasive Resistant Pump) series was developed specially for the conveyance of water contaminated with grainy or fibrous solids. The ARP highpressure pumps deliver operating pressures up to 400 bar. The pumps also work reliably at a solids concentration of up to 3,000 mg/l and a grain size of up to 300 μm.
Request for a quoteWOMA GMBH
Germany
The highpressure pumps of the 2series with operating pressures up to 750 bar and volumetric flow rates up to around 230 l/min are ideal for cleaning pipes and tube bundles, containers and containers.The seal system of this plunger pump is very easy to maintain due to fewer wearing parts. The ceramic plungers used are highly resistant to acid and alkaline liquids. The 2series impresses with a good price/performance ratio due to long service lives – even in rough everyday work.
Request for a quoteWOMA GMBH
Germany
With operating pressures of up to 1,000 bar, the Yseries pumps are ideally suited to a wide variety of cleaning work, e.g. in the chemical industry, oil and gas industries as well as in the area of ship cleaning. Due to the small size and low weight, they can be easily installed in unit with very small base frames.
Request for a quoteWOMA GMBH
Germany
The highpressure pumps of the Z series deliver operating pressures up to 1,500 bar. With a high number of pressure and nominal flow rate combinations, the pumps are preferably used in industrial cleaning, paint stripping and also in descaling.For pumps with an operating pressure of more than 1,000 bar, hard metal plungers are used, which are particularly stable in order to guarantee a long service life and thus low maintenance costs.
Request for a quoteWOMA GMBH
Germany
With the builtin central valve design, these plunger pumps also have high volumetric efficiencies at high pressures. The carbide plungers used are extremely robust, provide long service life at very high pressures of up to 3,000 bar, and can therefore guarantee low maintenance costs. This makes the pumps of this WOMA series ideal for separating, disassembling, stripping and derusting with high pressure water.
Request for a quoteCARL FRIEDRICH USBECK KG
Germany
220 g / 400 ml, capacity 3 h, 70 % butane, 30 % propane
Request for a quoteR+L HYDRAULICS GMBH
Germany
Cleaning covers Filter and breather filter Level indicators Oil level gauges Plunge heater
Request for a quoteJOKA WERKZEUG- UND MASCHINENBAU GMBH & CO. KG
Germany
Press-independent tools, for individual use or integrated in systems.
Request for a quoteR+L HYDRAULICS GMBH
Germany
Wide variety of types Materials Al/GG/ST Optional intermediate flanges Design according to VDMA 24 561
Request for a quoteR+L HYDRAULICS GMBH
Germany
High quality at a fair price Many years of experience Fast, reliable delivery Customer specified manufacturing
Request for a quoteR+L HYDRAULICS GMBH
Germany
Design acc. VDMA 24 561 Damped versions Eaasy replacement Spacesaving Pressure up to 16 bars
Request for a quoteBURRE HYDRAULIK GMBH
Germany
shock absorber in vertical mills
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
R+L HYDRAULICS GMBH
Germany
For types RD350 + RD475 Small quantities at fair prices Increases the visibility of your company
Request for a quoteR+L HYDRAULICS GMBH
Germany
Low cost noise reduction Effective damping Resistance against mineraloil
Request for a quoteR+L HYDRAULICS GMBH
Germany
Storage reduction to motors, frame IM B5/V Simple motorexchange Ductile iron for heavy duty applications
Request for a quoteR+L HYDRAULICS GMBH
Germany
Effective volume up to 123l High availability Cooling capacity up to 2,1kW Optional alu / steel lid Constant high quality
Request for a quoteKAMAT GMBH & CO. KG
Germany
Our valves are manufactured in-house and matched to the characteristics and pressures of your application. Our valves are full lift safety valves and can be spring loaded or pilot operated. All our valves are supplied set to your required working pressure up to a maximum of 4,000 bar and flow rates up to 4,700 l/min. Two versions of spring-loaded safety valves, even ATEX compliant The simpler high pressure valves have a rotatable bypass connection to dispose of leaking fluid. Pilot operated valves require a block flange. Like all other KAMAT products, these are ATEX compliant and can be manufactured in special materials to suit the medium being pumped.
Request for a quoteGSW SCHWABE AG
Germany
shock dampening for low operating noise levels absolutely sturdy and warpresistant body design with heavy doublepost guides to smoothly cut even toughest materials with adjustable blade clearance for a most precise cut at any thickness very precise blades made of special steel high operating safety through material guide at entrance and protective cover springactuated hold down clamp (from 250 mm stock width) top/bottom dead center control to monitor blade position counter control mounting bracket hydraulic power units in different sizes electrical control
Request for a quoteGSW SCHWABE AG
Germany
shock dampening for low operating noise levels thanks to a heavy overall frame and the sturdy, warpresistant design with heavy doublepost guides even toughest materials can be cut smoothly with adjustable blade clearance for a most precise cut at any thickness very precise blades made of special steel high operating safety through material guide at entrance and protective cover springactuated hold down clamp (from 250 mm stock width) top/bottom dead center control to monitor blade position counter control mounting bracket hydraulic power units in different sizes electrical control
Request for a quoteGSW SCHWABE AG
Germany
GSW Shears find their place in CutToLength Lines or as Scrap Choppers. They are used to perform lasting and costefficient, no matter the roughness of the environment. Our pneumatic and hydraulic Shears are designed efficient in any way – and from 60 to 1500mm width The pneumatic machines run with up to 500 SPM while their heavy types are robust enough to lastingly process up to 3mm thick materials. Since they do not need hydraulic power or electric controls, they are extremely costefficient. If a combination of high SPM and thicker materials is necessary, our TSHL „light“ hydraulic Shears offer the solution. The TSHS series machines are built very heavy and stiff which allows them to cut up to 12mm thick materials. If yet larger widths than 1500mm are to be processed, we work together with most reliable German partners who supply us with highquality Shears in hydraulic, electric or servoelectric design. This way we can offer the very best suitable solution for any application.
Request for a quoteGSW SCHWABE AG
Germany
With threephase servo drive sized according to job requirements Machine body in sturdy clean steel plate design Rollers made of highquality 63 RW tool steel, hardened and polished Pneumatic pilot release with parallel lift of upper roller, guided on gear rack Entry catenary rolls Manual edge guides Simple programming of even complex feeding cycles, Display in cleartext Manual functions for setup such as creep speed, jog mode, single feedtolength Simple memory and recall of job programs for quick changeover Mounting bracket with height adjustment via spindle or hydraulic handpump (optional motorized) Hard chromed or polyurethane coated rollers (optional with Topochrome coating for highgrip feeding) Measuring wheel system for highest feeding accuracy Stroke limitation for faster piloting Fine adjustment of upper roller and strip guiding device for thin stocks (starting at 0,1 mm thickness) Central edgeguides with hand wheel
Request for a quoteGSW SCHWABE AG
Germany
All rollers hardened and finepolished Multiple backup rollers to prevent deflection Specially suitable for highstrength steel applications Parallel adjustment of upper roller bank with tilting via spindle type lifting devices With optional synchronized drive of pinch and work rollers Drive system via transfer gear box and universaljoint shafts with length compensation and quickrelease coupling Warpresistant stand in modular design to allow extension with catenary rollers, threading system, loop bridge or conveyors for operation as partsstraighteners etc. Hard chromed rollers Polyurethane coated rollers Hydraulic threading systems in different grades Motorized adjustment of upper roller bank with optional jobmemory Central edge guide adjustment via handwheel (optionally motorized) All roll drive Extricable and exchangable roller cartidges for easy maintenance Quickthreading feature for universaljoint shafts Movable base Manual or hydraulic loop bridge Conveyor belts... etc.
Request for a quoteGSW SCHWABE AG
Germany
For onesided loading, GSW has five product series – and can thus answer basically any need in coil size, weight or width LHD, the light Coil Reel for up to 1 ton coil weight, with bevel gear expansion; LMHD, the light Coil Reel of our mid series for up to 1,5 ton, with lever arm expansion; MHD, the medium Coil Reel for up to 6 ton, with mechanical or hydraulic lever arm or key wedge expansion; SHD, the heavy Coil Reel for up to 25 ton, with hydraulic key edge expansion and SHZ, the twosided Coil Reel to handle heaviest and very wide coils. Performance data up to 30t coil weight and max 16mm material thickness max crosssection approx. 2000 x 5 mm max pulloff, decoiling or recoiling speed approx. 80 – 150 m/min
Request for a quoteGSW SCHWABE AG
Germany
To serve coil stock thicknesses of up to 15 mm Large diameter entry pinch rollers for smooth and lowwear strip transport Synchronized drive of all bottom work rollers and both entry pinch rollers Rollers are kept perfectly parallel with their penetration shown on scales or dial gauges Hardened 63 rockwell rollers with finepolished surface guarantee longevity Enormous potential for performance and straightening quality through absolutely warpresistant head construction; supported by optional backup rollers and allroll drive system Warpresistant body in modular design to allow extension with catenary rollers, threading system or loop bridge, etc. Hard chromed rollers Polyurethane coated rollers Hydraulic head opening as "cleaning stroke" Hydraulic threading systems in different grades Dial gauges for roller adjustment display Motorized adjustment of straightening rolls Jobmemory for mot. straightening roller adjustment Central edge guide adjustment via handwheel All roll drive
Request for a quoteResults for
Hydraulic- - Import exportNumber of results
116 ProductsCompany type
Category