Lip seals - Import export

iglidur® sealing lip bearing d1 [mm]: Quick and easy-to-mount polymer bushing made of iglidur® J (JDSM) or iglidur® V400 (VDSM) with clip-on radial shaft seal ring as sealing for the rotating shaft. Seals off against dirt, dust as well as all pressure-less media. Polymer bushing with clip-on radial shaft seal ring Sealing for rotating shaft Temperature application range like iglidur® J Coefficient of friction only 10% higher than in iglidur® J Coefficients of friction identically exceptional like iglidur® J Reduced installation space as well as easy and simple mounting Realizable with numerous sealing types High-temperature option VDSM possible Temperatures till 150° C Material: iglidur® J High temperature option VATM, iglidur® V400 Seal ring made of fluorelastomer Bearing-sealing combinations for other applications on request When to use it? When the penetration of dirt and spray water should be prevented When only a small installation space is available in the axial direction When an existing seal should be integrated in a plain bearing When not to use it? When pressurized media should be sealed When absolute impermeability to the shaft and housing is needed continuously We'll gladly do the developing with you iglidur® sealing lip bearing d1 [mm]:

The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips The troubleshooter for energy supply systems in the chip area - available in 4 sizes. Chips and dirt can affect the service life of cables and hoses significantly. With the RX system, igus® offers an extremely tight plastic e-tube that is nonetheless very easy to open. Snap-open in the outer radius A smooth, curved outer contour prevents chips from sticking Injection-molded "sealing lips" all around No holes, cracks, undercuts Series RX40 is IP40 tested (TÜV Saarland) Interior separation and guide trough available Covered pin/hole connection and stops "RBR" version with bending radius on both sides available Typical branches of industry Machine tools All applications in the direct chip sector Applications exposed to dust and dirt General mechanical engineering Dimensions and technical datas RX e-tubes Chip tests in the igus® laboratory demonstrate the tremendous chip-proof properties of the igus® RX tube. Chip-proof - for all types of chips and applications RX32 Inner height hi: 42 mm Inner widths Bi: 80mm Bending radii R: 80 - 250 mm Pitch: 32 mm RX E-Tube RX40 Inner height hi: 52 mm Inner widths Bi: 100 mm bending radii R: 100 - 300 mm Pitch: 40 mm RX E-Tube RX48 Inner height hi: 62 mm Inner widths Bi: 120mm Bending radii R: 120 - 325 mm Pitch: 48 mm RX E-Tube RX56 Inner height hi: 73 mm Inner widths Bi: 140mm Bending radii R: 140 - 350 mm Pitch: 56 mm RX E-Tube RX56 High-temperature plastic version of the chip-proof RX energy tubes from stock - 850°C from 24h RX - from stock against hot chips Submersion test in water - Various tube types were submerged under water. The new RX tube needs over 30 seconds until it is filled up, thus proving its high leak tightness Y = time in seconds A = igus® products B = competitor Chip penetration test - Various types of tube were exposed to a defined quantity of chips. In the new RX tube, after 80,000 cycles only 0.2 g of chips were found in the interior Y = chip mass [g] A = igus® RX e-tube RX40.100.100 251.900 cycles B = igus® e-tubes 68.10.100.0 256.132 cycles C = test tube 01 250.907 cycles D = test tube 02* 2.600 cycles *Teststop after 2.600 cycles E = igus® products F = competitor E-Chain® selection aids You can find the right E-Chain® quickly by entering concrete parameters and with the aid of a comparison table. Productfinder Assembly instruction Dismantling / assembling a cover, replacing a chain link and assembling / inserting the RX tube. Assembly instruction Configure interior separation Define cables, select chain and configure interior separation. Now also for RX tubes! Interior separation configurator Application examples Applications in various industrial sectors. RX tubes Series RX - new chip-proof design, small pitch, removable cover 1 Chip-proof design without undercuts and edges 2 Excentric locking 3 Material igumid G 4 rounded shape 5 covered pin/hole connection RX tubes IP tested Technical report TÜV NORD red dot 2011: honourable mention for RX40 iF-Design-Award for RX e-tubes ESD classification: Electrically conductive ESD/Atex versions on request UL94-V0 classification on request e-tubes available as special design with HT material for 850°C hot chips

The PFLITSCH CABseal is used to feed pre-assembled and non-assembled cables, as well as pneumatic and hydraulic lines, simply and reliably into control cabinets, primarily, but also into enclosures and machines. To this end, their sizes and dimensions of the frames are compatible with the common standard cut-outs and hole patterns in control cabinets so that just a single CABseal frame is required per cut-out. The CABseal cable entry system consists of four different sized frames and a number of cable grommets that can be equipped in various constellations. The grommets are slotted at the sides to make it easier to insert cables. While the frame is made of hard and robust polyamide, we use a flexible elastomer for the cable grommets and their special sealing lips. To ensure the cables are properly sealed, the grommets are positioned in the frame and compressed when the upper part of the frame is screwed down.

Rectangular case in anodised aluminium - Shaft in stainless steel - Shaft entry either with floating guidence against dust (AF) or with lip seal (AG) to protection grade IP 65 - Conductive plastic resistance elements - Precious metal wipers - Axial connector or axial or radial cable exit - Ball joints at shaft end and / or case on request.

Cable conduits made of PE-HD with plug-in sleeve Manufactured acc. to DIN 16876 Standard design: Sleeve type: integrally moulded plug-in sleeve (SM) Sealing ring: compression lip sealing ring, type “SX” (inserted in the factory) Sharp end: with plug-in depth marking and chamfer Length: 6 m Colour: black Inner surface: smooth Possible designs: Quality: DIN 16874 Length: 1 m to 6 m Coloured stripes: co-extruded Colour: on request Outer surface: coloured co-extruded or solid dyed Inner surface: inner grooves for reducing the cable pull-in forces Labelling: acc. to customer specifications

Flat Strips with lip for covering the joint between the window frame and wall, for use in drywall construction, interior fittings for connection to the wall. With soft lip extending on to the wall and adhesive tape cover for the adhesive tape. Acrylate foam tape grade, 1 mm thickness, weather and ageing-resistant, permanently elastic. Can also be supplied coated with Renolit MBAS wood and single-colour decorative finish. Decorative wood profiles with soft lip in matching colour.

For use inside and outside, for manufacturing or retrofitting windows with bars. Bar profile in white tones or covered in foil with lips in black, grey and white, weather-resistant and anti-aging foam tape. Window bars in PVC U window quality, new goods. With RAL-tested TPE soft lip material. Acrylate foam tape quality, weather-resistant and anti-aging, permanently elastic, certified by ift-Rosenheim. Wood and one-colour decorative window bars covered in weather-resistant and anti-aging Renolit MBAS or Cova foil. Window bars can be used with and without spacers (Georgian bars) in insulating glass.

Renolit MBAS and Cova film, weather and ageing-resistant, wood and single-colour decorative finishes, glazing bars – black sealing lip, flat strips – coloured sealing lip. Call to check stock availability

Renolit MBAS and Cova foils, weather-resistant and anti-aging, wood and one-colour decoration, glass window bars – black sealing lip, flat rails – coloured sealing lip. Call to check stock availability

Our KIS track rollers are available as self-retaining, single or double row ball bearings with particularly strong outer rings. In addition to high radial forces, they also absorb axial forces in both directions. Track rollers are characterised by their robust construction featuring particularly thick-walled outer rings with a crowned outer surface (alternatively with a cylindrical outer surface or outer profile). They are designed to carry high radial loads and also tolerate axial loads that can arise due to minor misalignments, skewing or short-term start-up shocks. The assembly is constructed with a fixed inner ring mounted on axles. In this case, the track rollers are not installed in a housing bore, but are supported on a flat raceway (mating track). To ensure a reliable seal, the track rollers are fitted with a lip seal or cover discs on both sides. This prevents the ingress of dirt, dust and other contaminants while maintaining lubrication inside the bearing.

Valve tapping bridge with service shut-off and for tapping 1 "- 2". Combination rubber insert chambered with several micro-sealing lips. Seal material according to KTW / W 270. Seal the bore with the auxiliary shut-off via the side outlet and seal it after tapping until the valve bonnet is reassembled. For each dimension, a top with matching clamp. scope of application • for plastic pipe (PE or PVC) DN 50 - 200 • for sluice-free, upper tapping under pressure by means of Rehbein auxiliary valve • for water up to PN 16