Export-&-import - Import export

Retractable Power Distributor/power bollard SV501 for indoor and outdoor use, made of saltwater-resistant aluminum. Due to its solid construction, the SV501 lowering distributor can be driven over by a truck, of course, only when the lid is fully closed. The surface is anodized with a stainless steel look. The retractable power distributor SV501 is equipped with 8 protective contact sockets 2 / 16A 230V with hinged cover (unsecured, without wiring). The devices are raised and lowered using a crank. Drainage is required for outdoor installation. The housing is watertight when closed, protection class IP67. Alternatively, other combinations are also possible. Further equipment variants and colors on request.

Floor box 8808T with 8 slots made of polished stainless steel. It can be installed at any point in the floor, as pipes are used for the line feed. Because of its low height, this version is particularly suitable for floors in old buildings. The lid is designed for the inlay of carpets, cork floors or the like, with a covering thickness of 5–7 mm, and closes even when the plugs are inserted. Further equipment variants on request.

Round hollow floor tank 9908A with a housing made of sendzimir galvanized sheet steel, rim and lid made of solid aluminum with a lid for laying on. The cover also closes in a straight or angled shape when a standard plug is plugged in. The reversible lid is anodized in natural aluminum or can be covered with a carpet, etc. Other equipment variants on request.

Raised access floor power system 8512BK with 12 slots. The housing is made of sendzimir galvanized sheet steel. The insert lid and frame are made of 1.5 mm thick stainless steel. The lid is removable and can be covered with a 15 mm floor covering such as Stone, wood etc. The bottom of the receptacle box can be opened for subsequent pulling of cables without affecting the connected units. Further equipment variants on request.

Raised access floor power system 9904AK with height-adjustable floor socket and 4 slots. The housing is made of sendzimir galvanized sheet steel, the frame and the insert lid are made of solid aluminum. The lid is anodized in natural aluminum and can be fitted with floor coverings. It closes even when the standard plug is inserted. The bottom of the receptacle box can be opened for subsequent pulling of cables without affecting the connected units. Further configuration variants on request.

Hanging distributor HV1006 made of stainless steel with 6 units: three Schuko sockets with VDE certification, one CEE 5/16A 400V/6h socket with VDE certification, one RJ45 double CAT6A and a compressed air coupling. Ideal for use in workshops. The hanging distributor HV1006 is delivered with hooks and carabiners (without cables, hoses and wire ropes shown).

Aluminum leveling ring 12251 for floor socket 7702A and 7704A for use in wooden floors or raised access floors. The leveling ring is attached to the floor socket with screws and screwed onto the floor from below. The delivery takes place with grub screws, but without illustrated fastening screws and illustrated floor socket.

Rain protection set 12255 consisting of an extension made of PVC and a black protective cap made of soft PVC for the floor sockets 7702A and 7704A. The rain protection set offers ideal protection against rain with plugged-in connections.

Wall socket 5501A with one slot, splash-proof, with protection class IP44. The hinged lid can be locked with a key and is therefore primarily protected against unauthorized use. The storage box is made of sendzimir galvanized steel sheet. The frame and the lid are made of solid aluminum and anodized in natural aluminum. Further colors and equipment variants on request.

Wire forms can have a shape that is limited almost only by fantasy. Many of them have some kind of spring functionality, for example some quick fastening applications. In most products, the material is stressed in bending and they can be looked upon as leaf springs made from wire. Wire forms are manufactur

Multi-coil wave springs are made from flat-rolled spring wire that is coiled to a helical shape and the coils are at the same time given a sinus shaped wave form. The force-deflection relation is created by flattening out the wave form when the spring is compressed. The function is hence like a helically shaped leaf spring.

Volute Springs are used as compression springs and made from flat material coiled to a volute. The coils of the material overlap each other and are guided radially by each other during compression, thus giving the spring a stability against buckling that cannot be achieved with conventional compression springs.

Many applications require two similar springs, but with one right-hand coiled and one left-hand coiled. In some cases, these two springs can be combined into a double spring, which has one right and one left-hand coiled spring body connected to each other.

Torsion bar springs is a good alternative to clock springs or helical torsion springs, when a rotational torque is needed in applications where the spring shall fit into a space that is limited radially, but with lots of space axially.

Most common ends are different types of end loops and hooks, there are also a wide range of other mechanical attachment possibilities such as coiled in and screwed in attachments. Examples are, half hooks, German loops, English loops, extended hooks, side hooks, side loops, screw plugs and screw shackles.

A snap or retaining ring is a fastener or retaining ring that consists of a semi-flexible metal ring with open ends that can be snapped into place. It fits in a groove on a shaft or inside a bore and locates the shaft axially in one direction.

A Garter Spring is a circular ring made from a coiled helical spring bent into a circle and with the two ends connected to each other. A garter spring will create a radial force directed towards its center when the radius of the garter spring increases.

Constant Force Springs are manufactured from flat strip material and spooled to a specific curvature matching the needed pull force. There is practically no limit on extension speed and acceleration. The springs can be fitted in a number of ways and extended partly or completely.

Compression springs is the most common type of springs. The majority of compression springs are cylindrical and linear, but to this group belongs also conical, barrel shaped, tapered out ends and more. The design can be adjusted to fulfill a wide range of requirements concerning spring characteristic.

Clock Springs – also called hair springs – is a torsion spring that is optimum for installation spaces that are limited axially, but with more space radially. They are made from strip material or flat rolled wire that is wound in a flat, spiral shape.

Lesjöfors manufactures deep drawn parts to customers individual requirement in press machines by either progressive tool or transfer tool solutions as well as opportunities for less automated solutions in case of low volume requirement.

We manufacture bushings using either bending technology or stamping technology. This production type provides a cost-effective alternative to other time- and material-consuming manufacturing processes.

Wave Washers are washers with a wave form and gives an axial force when the waves are flattened out during compression. The function is similar to wave springs, but wave washers have only one coil

We have over 150 years spring manufacturing experience, and today produce the world’s largest range of coil springs for the automotive aftermarket. In addition to replacement coil springs, we also stock market leading ranges of Gas, Leaf and Sport springs.

As part of a global design, manufacturing and technological development network which includes sites in Cornwall, UK, Lesjöfors in Sweden and Åminnefors in Finland, our manufacturing excellence and customer service is dedicated to world-leading products and services.

Modern manufacturing faclilities using the latest in design and production technology ensure consistent, high quality, long life products that are competitive priced.

Lesjöfors’ range of standard springs consists of over 10,000 different items. Our highly efficient store of standard springs guarantees high delivery reliability. All our standard springs have been posted as 3D CAD models, and are available for downloading.

The Dutch Lesjöfors company Tribelt specializes in developing and manufacturing metal conveyor belts. For more than 70 years, the company has solved problems for customers in many different fields across Europe. We also manufacture sprockets, customized for the design and in the number your application require, its’ tension forces and surrounding environment.

Floor socket 3303E made of stainless steel, ground, with hinged lid. Particularly suitable for low installation depths, e.g. in the exhibition area, kitchen, etc. Further equipment variants on request. The frame and the lid are made of 1,5 mm stainless steel and the receptacle box is made of sendzimir galvanized sheet steel.