Dust filter - Import export

synthetic filter media or filter media with irregular layer of coarse glass fibres individual pads or filter rolls available small installation depth low acquisition costs

ISO CoarseISO ePM10 / G4M5 pleated, progressivelystructured filter media thermallybonded, synthetic nonwoven (polyester) hotmelt pleating system synthetic FIBERPLAST frame standard installation depths 20, 25, 47, 92 mm special design with different frame geometries simple handling optimum resistance performance through hotmelt pleating system low pressure drop moistureproof fully combustible

The filter housing is made of sturdy steel plate with a reinforcement of structural steel frame. Equipped with inlet and outlet openings for the dusty or filtered air. The inspection cap is used to control the automatic filter and has a flap for access to the built-in filter cartridges. These are made of folded polyester material having a filter area of each of 8 and 14 m². Provided with upper and lower reinforcing rings of plastics material for fastening in the holders. The dust drawer is equipped with wheels, allowing easy extraction during disposal of the dust. The centrifugal fan with a flanged electric motor and the fan / motor unit is built up in the filter housing - the motor is bolted with its flanges on the filter housing and surrounded by the sound enclosure.

CF 30 G equipment is supplied completely assembled and ready for operation. The dust collection unit is suited for intermittent operation only, because regular cleaning of the pocket filter element in certain intervals is an absolutely must for the proper operation of the equipment. The cleaning intervals will depend on the operating conditions and must be established by experience. Normally cleaning intervals will be between operating times of 30 minutes to two hours. It is a prerequisite for sufficient and intensive cleaning of the filter cloth that dust collecting is interrupted during cleaning to achieve static pressures on the filter material. A retention time of 1 - 2,5 minutes between the end of the suction and the beginning of the cleaning process is therefore required. The filtered air must be removed outside - do not lead back to closed rooms!

Economic acquisition, powerful performance values and simple handling – these characteristics are combined in a robust metal construction of the air cleaner TAC 1500 S that is suitable for use on construction sites. Its Monoventic regulator enables you to steplessly adjust the air volume precisely to your actual needs, and the flexible filter system allows for the use of variable filter combinations for every construction site situation. With the TAC 1500 S you can reliably filter coarse and fine dust or spray paint mist as well as concrete dust, fine sanding or plaster dust and highly dangerous quartz dusts or asbestos fibres. The filter frame can be flexibly equipped with one or two filter elements, for example a G4 filter or an additional F7 filter, so that in combination with the HEPA filter a two- or three-stage air purification process in accordance with dust class H can be achieved.

With high-quality filter tubes and PTFE diaphragms. Paint dust filters Wet painting also results in overspray. Overspray is the solid portion of the paint that is not taken up by the workpiece. According to the purpose of use, the overspray is moist and sticky immediately after release. It is captured by the exhaust air stream in the spray booth and fed to a filter. This can be, for example, a baffle plate filter, paper filter, fleece filter, glass fibre filter or also combinations of these. The adhesive effect causes the paint particles to adhere to the contact surfaces of the respective filter medium, as a result of which a good degree of separation is achieved. However, all these filters are storage filters, i.e. the filters clog up more and more during operation and cannot be regenerated. A filter exchange becomes necessary if the exhaust air rate of the spray booth falls below the minimum. This can be very time-consuming under certain circumstances and the work process must be interrupted in order to do it. To make things worse, not only must the filtered and bound paint residues be disposed of, but also the actual filter materials. Such tooling times are not justifiable for automatic, continuous or multi-layer painting processes. Continuous procedures such as automatically cleaned filters are likewise required for this. The humidity and the adhesiveness of the particles to be filtered are thereby the problem. In order to solve this problem, the paint particles should be relieved of their adhesive capability as far as possible whilst still inside the paint booth. Our patented ‘RTS-Rotation’ system is outstandingly well suited for this. The system is comprised of slowly rotating brush rollers, which take up the adhesive paint particles on the surface of the bristles and allow them to dry there. The bristles are automatically regenerated at pre-specified time intervals by combing devices that swing in at the rear of the brush rollers. The dislodged paint residues can then be removed and disposed of either manually during work breaks or automatically during operation. The degree of separation of this system is, however, insufficient to satisfy the environmental protection requirements concerning residual dust content in the exhaust air. A further filter stage is necessary for that. It must be assumed that the paint particles arriving here are to a certain extent still damp and sticky. For this we use special paint dust filters with high-quality filter tubes with PTFE diaphragms. If necessary, precoating agents (auxiliary dust) are used in order to neutralise the adhesive capability of the particles and to keep the dust layer on the filter elements permeable to air. The precoating agent is injected into the raw air pipe by means of special dosing units. The filter tubes are cleaned by means of compressed air impulse cleaning. The use of this technology requires special know-how. We have had the appropriate experience for almost ten years. The implemented plants have capacities ranging from 5,000 to 90,000 m³ /h. Because of the large number of different paint systems, individual experiments are usually necessary in our pilot plant in order to find the correct solution for the individual case.

Type RK/RF for continuous operation, suitable for virtually all types of dust. Round filter type RK / RF The round filters from this series are suitable for continuous operation and for almost all types of dust. What is special about them is the rotary cleaning device, which causes the dust to be sucked out of the filter hoses and discharged. Using other methods the dust is also continuously dislodged from the filter element, but contaminates the other filter elements in the next moment. Only a small part of the dislodged dust falls down and is discharged. The lower part of the filter is implemented like a cyclone and acts as a pre-filter, where coarse dust is already separated and discharged. Compressed air impulse cleaning is also possible as an option here. The filtering direction of the filter hoses is from the outside inwards. The hoses are provided with support frames.

These are ideally suited for extraction from one or more sources of dust and are predominantly used in small and medium-sized enterprises for air quantities of up to 6,000 m³/h. ES 200P/280P deduster with jet cleaning The ES 200P deduster is designed for an air quantity of max. 3,000 m³/h and has one dust collection container; the ES 280P is designed for max. 6,000 m³/h and has two dust collection containers. The ES deduster is made of galvanised sheet steel and is a universal device for the extraction and separation of various types of swarf and dust. The raw air inlet nozzle has a non-return valve arranged upstream of the device. The filter works according to the downdraft principle, i.e. raw air is fed to the filter cartridges from above. This construction results in extremely efficient pre-filtration and preserves the filter medium. The filter cartridges are cleaned by means of compressed air impulse. Swarf and dust is collected in the mobile containers arranged underneath. The fan, which is arranged on the clean air side, is equipped with a high-performance impeller. The clean air outlet opening has a sound-absorbing lining. The electrical controller is directly attached. Equipment Optional: 280P / PAS deduster MS multi-extractor with double-walled filter sack The built-in radial fan sucks off dust and swarf at the place of generation and forces it via the impeller into the air injection frame. The swarf collects in the dust or swarf sack. The dust/air mixture flows into the filter sack, where the dust is filtered out. The cleaned air is fed directly back to the operating area. The double-walled filter sack offers a significantly larger filter area compared to other designs. Filter cartridges are also possible here as an option. The filter elements are cleaned manually. The multi-extractors are predominantly used with coarse-grained and unproblematic types of dust and swarf. The devices are not suitable for continuous operation or for wood dust and splinters. Three sizes are available for the following maximum air quantities: Type MS 160 up to 2,000 m³/h Type MS 200 up to 3,000 m³/h Type MS 250 up to 5,000 m³/h

Compact filters are characterised by the fact that they essentially unite fan, filter element and discharge or dust collection facility in one. The capacity range of the compact filters extends up to 20,000 m³/h. Different systems and modes of operation are available for the individual assemblies, resulting in a large number of possible variants. This allows us to offer a large range of solutions for dedusting tasks. Based on our many years of experience, we select the filter media from those available on the market that are best suited for the most diverse types of dust and tasks. Filter hoses, filter bags, filter tubes and filter cartridges are used as filter elements. Cleaning takes place using compressed air impulse, low-pressure purge-air or shaking. Fans from own development and production enable us to design a highly efficient and precise layout. Discharge usually takes place directly into collecting containers, such as dustbins with snap fasteners, or into containers, big bags, or via discharge mechanisms into automatic disposal systems. Screw conveyors, drag conveyors, rotary systems, cellular wheel sluices, double-gate sluices and slidegate valves are available as discharge mechanisms. Intelligent control systems, piping elements, silencers and pre-coating devices for auxiliary dusts are standard items in the range. Naturally we also use our know-how to create needs-based custom solutions.

Separation of paint powder from powder coating booths. Options: Rippert powder filter This type of filter is particularly suitable for the separation of paint powder from powder coating booths and is also often used together with an upstream Rippert cyclone for powder recovery. Separation chamber with dust collecting container, filter cartridges, compressed air cleaning and sound-insulated fan are housed in a compact design. The filter cartridges are arranged vertically in order to ensure optimum cleaning behaviour and energy-efficient operation. The fan, which also comes from our own production, is characterised by smooth running and high efficiency. Standard advantages:

incl. check valve and filter Service pressure: 0-26 Mpa Service temperature: -40°C up to 85°C Reliable in filling and operation direction Small construction Corrosion-resistant All seals are suitable for CNG Certification: ECE R 110 The valve is equivalent of heavy metal regulation Burst pressure: > 100 Mpa, 20° Orfice diameter: 4 or 6mm, connection for 6, 8mm tube or 3/8" Filter: 50µm Dust protection cap, optional Tightness: 1x10-5mbar l/s, 20°C, 100% He

incl. check valve and filter Service pressure: 0-26 Mpa Service temperature: -40°C up to 85°C Reliable in filling and operation direction Small construction Corrosion-resistant All seals are suitable for CNG Certification: ECE R 110 The valve is equivalent of heavy metal regulation Burst pressure: > 100 Mpa, 20° Orfice diameter: 4 or 6mm, connection for 6, 8mm tube or 3/8" Filter: 50µm Dust protection cap, optional Tightness: 1x10-5mbar l/s, 20°C, 100% He

incl. check valve and filter Service pressure: 0-26 Mpa Service temperature: -40°C up to 85°C Reliable in filling and operation direction Small construction Corrosion-resistant All seals are suitable for CNG Certification: ECE R 110 The valve is equivalent of heavy metal regulation Burst pressure: > 100 Mpa, 20° Orfice diameter: 9mm, connection for 8, 10, 12, 16mm tube or ½" Filter: 50µm Dust protection cap, optional Tightness: 1x10mbar l/s, 20°C, 100% He

plane, compact design 4layer filter media coarse dust protective layer, 2 layers of activated carbon and abrasion protection layer at clean air side activated carbon layer of carbonimpregnated, reticulated PUR foam solid galvanised metal frame, with metal grids on both sides best combination of low pressure drop and adsorption capacities

Special features of our model range SUPER BABY: • Compact and elegant design • Simple operation • Low material consumption • Highly efficient dedusting • Efficient function • Environment-friendly function without dust harassment • Adjustable material consumption The SUPER BABY has a large door that opens to the top and allows to put in the work pieces easily. Due to the mounted sinkhole the blast media circulation is possible without any other additional equipment. With the controls to adjust the blast media it is easy to adjust the blast-media consumption and to change the blast media type. A built-in nozzle-holder and an injector type blast-head with hardened air- and blast nozzle (manual operation), as well as a working grid allow an easy operation. A Shock-resistant linear fluorescent luminary gives glare-free light in the work area. Efficient injector sandblasting booth Superbaby. Direct from manufacturer, MADE IN GERMANY.

Beam machine for irradiating a glass sheet conveyor belt Transport device supporting roller guide, motor nozzle movement, infinitely variable, attached dust filter system and electronic Control. Max. Lens height for automatically rays 1.200 mm Max. Lens height for manually rays 1.500 mm

The Modellrange ECONOMIC is made of durable sheet steel. It comes with adjustable media consumption, a blast media collection bin and a sieve to separate blast media from contaminations. The cabinet has two lateral openings with sealing sliders for rod materials. A perforated metal plate with enforcements. The system has a sectional door that opens the complete workspace. The Cabinet comes with a door-safety switch, two large operation holes with multiple rubber Sealings. Monitoring window, sized 400x500 mm, with easy changeable glass/safety-glass panes, as well as 2 durable pneumatic springs. Energy Saving Lamp, attached from outside. Injector-type blast head, with air- and blast nozzle made of hardened steel. The system comes with all necessary compressed air and blast media hoses, oil-water separator, manometer, an electrical magnet valve and a foot switch. On/Off switch, dust filter system 0,55 kW, intermediate pressure turbine. Dust collection bag.

The disk pelletizers are used for the agglomeration of powdery primary and secondary materials such as filter dust. The primary area of application is the agglomeration of iron ore concentrate to form pellets with a target size of 9 to 16 mm. Inside the inclined cylindrical rotating container, a powdery input material is formed with or without the addition of an evaporated liquid binding agent. By changing the angle of inclination, rotational speed, material conditioning and disk rim height, the optimum operating parameters can be set. Advantages automatic adjustment of the disk rim height automatic inclination adjustment stepless rotational speed setting autogenic wear protection on the bottom of the disk pelletizer (honeycomb bottom) flexible scraper flexible spraying system integrated switch cabinet for easy operation, including control panel You’ll find detailed information in our product brochures and specification sheets.

For thermal insulation Temperature controlled up to 55 °C Optionally ULTRA.sens® or INFRA.sens® With dust filter Temperature range 5°C - 45°C