Coated seals - Import export

• The face shield is made of 1 mm thick Polycarbonate • Excellent optical quality • High resistance to temperature extemes approx. -50°C to +135°C • Good UV protection • High impact strength • IR-protection shade 4-6 • Additional protection of neck and chin due to fully enclosed face shield

• The face shield is made of 1 mm thick Polycarbonate • Excellent optical quality • High resistance to temperature extemes approx. -50°C to +135°C • Good UV protection • High impact strength • IR-protection shades 4-4 and 4-5 available • Additional protection of neck and chin due to fully enclosed face shield

• The face shield is made of 1 mm thick Polycarbonate • Excellent optical quality • High resistance to temperature extremes approx. -50°C to+135°C • Good UV protection • 94% of the radiant heat is reflected by the gold layer • IR-protection shade 4-5

• The face shield is made of 1 mm thick Polycarbonate • Excellent optical quality • High resistance to temperature extemes approx. -50°C to +135°C • Good UV protection • High impact strength • IR-protection shades 4-4 and 4-5 available • Additional protection of neck and chin due to fully enclosed face shield

• The face shield is made of 1 mm thick Polycarbonate • Excellent optical quality • High resistance to temperature extremes approx. -50°C to +135°C • Good UV protection • High impact strength • 94% of the radiant heat is reflected by the gold layer • IR-protection shade 4-4

• The face shield is made of 1 mm thick Polycarbonate • Excellent optical quality • High resistance to temperature extremes approx. -50°C to+135°C • Good UV protection • 94% of the radiant heat is reflected by the gold layer • IR-protection shade 4-6

OHLER offers a wide range of aluminum foil trays. All materials have been developed to be filled both manually and automatically. They are available in various sizes and thicknesses, and the trays can even be lacquered or printed. Our range of aluminum containers is complemented by a variety of accessories including aluminum lids, closing and sealing foils, coated carton lids, plastic snap-on lids, insulated transport boxes and closing machines. Our aluminum trays can be used both in microwave and conventional ovens or with barbeque grills. Aluminum food containers protect food from deterioration. The lightest “complete barrier” available, aluminum is impervious to light, gas, water vapor, oils, fats, oxygen and microorganisms. They keep foods fresh, safe and tasty, maintaining quality throughout a long shelf life.

The CS-3000 suspension system is characterised by a combination of well thought-out ergonomics and modern industrial design. It consists of a large number of components that can be combined in any way. The CS-3000 suspension system is an innovative system solution that functions according to the modular principle. — Long service life and safe operation thanks to anodised aluminium tubes — Clean lines, thanks to smooth transitions between the tube and system components (very easy to clean) — Coated tube fastening screws for sealing the thread holes and secure connections — Relative appearance and connection of narrow profiles thanks to the possibility of reducing the cross section from square to round tube — Protection class IP65 — Modular flexible system lets you upgrade the couplings (also after installation), e.g. with adapters for slim enclosures or with tilt adapters — Well designed ergonomics for simple and virtually fatigue free operation

Technical data Design Check Valve with threaded connection and with a EPDM coated ball. Connection Thread ¼” … 3″, acc.to ISO 228-1 Mounting position Horizontal, cap above and vertical Pressure range PN10 … PN16, see data sheet Temperatur range 0°C … +80°C Media Non aggressive liquids Material Body: GGG-50, FBE-coated Cap: GGG-50, FBE-coated Ball: Metal, EPDM-coated Seals: EPDM The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!

Technical data Design Check Valve with flanged connection and with a EPDM coated ball. Face to face EN 558-1 R48 Connection Flange DN50 … DN150, PN16 drilled, DN200 … DN300, PN10 drilled. Flanges acc. to EN 1092-1 DN65 – PN16 will be delivered in 4-hole execution! Mounting position Horizontal, cap above and vertical Pressure range PN10 … PN16, see data sheet Temperatur range 0°C … +80°C Media Non aggressive liquids Material Body: GGG-50, FBE-coated Cap: GGG-50, FBE-coated Ball: Metal, EPDM-coated Seals: EPDM The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Function Electrical operated Pressure discharge bidirectional Stem Not rising Pressure range Please refer to the data sheet Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy-coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Electric acting Pressure discharge One-sided Voltage 400V 3AC (24V DC, 230V AC on request) Pressure range Please refer to the table Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 8! Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge One-sided Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 Installation Only with vertical upwards actuator The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic double acting Pressure discharge bidirectional Pilot pressure 6bar (lower pressure on request) Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Lever Steel, lacquered Pressure discharge bidirectional Pressure range Please refer to the table Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Lever Steel, lacquered Pressure discharge One-sided Stem Not rising Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Hand wheel Steel, lacquered Pressure discharge bidirectional Stem Not rising Pressure range Please refer to the data sheet Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Pneumatic double acting Pressure discharge One-sided Pilot pressure 6bar (lower pressure on request) Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid