Results for
ABS SAFETY GMBH
Germany
This cross-shaped anchor for flat roofs is weighed down using concrete slabs (50 x 50 x 5cm, not included). The design is based on a high-quality stainless steel frame (150 x 150 cm) with aluminium crossbars and a central, stainless steel anchorage point for one individual (Ø 16 mm). EN 795:2012, E For flat roof pitches ≤ 5° Weighed down using 8 concrete slabs (ca. 224 kg) Weight incl. ballast: ca. 245 kg; resulting roof load approx. 108.9 kg per m² Also designed for usage as an intermediate post in a lifeline system Incl. 5 EPDM patches to protect your roof membrane
Request for a quoteABS SAFETY GMBH
Germany
This stainless steel anchorage point, which comes with a base plate (150 x 150 mm), has been approved by the German Institute for Construction Technology ("DIBt"). It is installed on a steel structure and countered on the other side. The welded-on supporting tube (Ø 42 mm) easily withstands the pre-tensioning stress to which it is subjected when used in a lifeline system. Our standard package includes a set of installation materials. National technical approval ("abZ"): Z-14.9-688 (pls. observe the installation instructions provided in the "abZ") EN 795:2012, A + CEN/TS 16415:2017 Base plate + welded-on supporting tube Incl.stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
Install the base plate (200 x 200 mm) of this stainless steel anchorage point (Ø 16 mm) on a load-bearing steel structure and then counter it using 4 stainless steel bolts. This anchor has been awarded national technical approval by the German Institute for Construction Technology ("DIBt"). The bolts and counter nuts required are included in the package. National technical approval ("abZ"): Z-14.9-688 (pls. observe the installation instructions provided in the "abZ") EN 795:2012, A + CEN/TS 16415:2013 Incl. stainless steel installation set Upgrade with a supporting tube for usage as an end or corner support in a lifeline system
Request for a quoteABS SAFETY GMBH
Germany
All you need to install this stainless steel anchorage point (Ø 16 mm), which is suitable for all directions of load, is an installation depth of at least 65 mm. The anchor base plate (200 x 200 mm) is fixed permanently to the concrete subsurface using the 4 drive-in dowels supplied. EN 795:2012, A + CEN/TS 16415:2013 Concrete ≥ C20/25 Installation depth required: Only 65mm Add a supporting tube for usage as an end or corner post in a lifeline system Incl. stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
This mobile door traverse provides your workers with a temporary anchorage option in a fall danger zone at a minute's notice. This robust steel traverse is simply jammed in a door frame. The anchorage eyelet can be used to secure up to 2 individuals simultaneously (when equipped with corresponding PPE equipment). EN 795:2012, B CEN/TS 16415:2013 Simply jammed in a door frame Maximum door width: 1100 mm For 2 individuals (max. 900 mm)
Request for a quoteABS SAFETY GMBH
Germany
This stainless steel anchorage point (Ø 16 mm) - specially designed for wooden surfaces - is attached to a load-bearing beam and accordingly countered. The anchor can be installed laterally using the angular plate supplied. Our standard package also includes 2 threaded bolts and matching nuts. EN 795:2012, A + CEN/TS 16415:2013 Angular plate for lateral installation 2-hole system for flexible installation For load-bearing wooden structures Minimum beam dimensions: 100 mm x 120 mm Incl. stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
For a high load-bearing capacity in any direction, simply insert this stainless steel anchorage point (Ø 16 mm) through a pre-drilled hole in a wooden beam and counter it on the other side. This anchor is available with and without a protrusion and can be installed on the ground, laterally or overhead. EN 795:2012, A + EN CEN/TS 16415:2013 Protruding and non-protruding models available Designed for load-bearing wooden structures Minimum rafter dimensions: 100 mm x 120 mm Incl. installation set
Request for a quoteABS SAFETY GMBH
Germany
This anchorage device was specially-designed for flat roofs. It can be used as an anchor or system support and can be weighed down using concrete slabs (50 x 50 x 5 cm, not included) or gravel (not included). Its high-quality, stainless steel frame (150 x 150 cm) with aluminium crossbars is equipped with a central anchorage point (Ø 16 mm) - also made of stainless steel. EN 795:2012, E + CEN/TS 16415:2013 For flat roof pitches ≤ 5° Weighed down using 16 concrete slabs (ca. 448 kg) Weight incl. ballast: 483 kg | resulting roof load: approx. 214.7 kg per m² Anchorage point for 2 individuals Weighed down using gravel (ca. 450 kg) Weight incl. ballast: ca. 485 kg | resulting roof load: approx. 200 kg per m² Anchorage point for 1 individual (secures 2 individuals when used as an intermediate bracket in a lifeline system) Additional supporting tube required for usage as an end or corner post Incl. 5 EPDM patches to protect your roof membrane
Request for a quoteABS SAFETY GMBH
Germany
Whether this device is left standing out in the open or integrated into your roof greenery, our ABS Weight OnTop Max anchorage device for flat roof surfaces has been approved for installation without penetrating your roof surface - simply by weighting it down (50 x 50 x 5 cm, concrete slabs not included). Please observe the installation instructions provided in the "abZ" (national technical approval: Z-14.9-824) For flat roof pitches ≤ 5° Weighted down using 40 concrete slabs (ca. 1.120 kg) | resulting roof load approx. 61 kg per m² If implemented as an end or corner post in a lifeline system, a special supporting tube needs to be used
Request for a quoteABS SAFETY GMBH
Germany
This anchorage point (Ø 16 mm) for sandwich sheeting is simply installed from above using 4 special toggle bolts. The anchorage eyelet, rod and base plate (372 x 200 mm) are all manufactured completely from stainless steel material. The special toggle bolts needed are included in the package. EN 795:2012, A + CEN/TS 16415:2013 Sandwich and trapezoidal sheeting (negative) For steel plating ≥ 0.5 mm Distance between the bores: 280 to 333 mm Installation materials included Add a supporting tube for usage as an end or corner post in a lifeline system
Request for a quoteABS SAFETY GMBH
Germany
The round base plate (Ø 400 mm) of this stainless steel anchorage point (Ø 16 mm) guarantees that any force exerted on it is optimally distributed across a thin installation surface. Our standard package includes 24 stainless screws which are used to attach the device to an OSB / wooden surface. EN 795:2012, A + CEN/TS 16415:2013 OSB min. 12 mm Wood min. 18 mm Can also be installed on a vapour barrier or waterproofing (max. 15 mm) Optimal force distribution through the round base plate design Incl. installation set
Request for a quoteABS SAFETY GMBH
Germany
The two sides of this stainless steel anchorage point (Ø 16 mm) - specially designed for the roof apex - can be adjusted to the individual pitch of your roof using its adjustable base plate. Our standard package includes 8 stainless steel screws for attaching the device to the rafters. EN 795:2012, A + CEN/TS 16415:2017 Simply screwed onto the roof apex Suitable for usage on both sides of your roof Min. roof rafter dimensions: 80 mm x 120 mm Add a supporting tube for usage as an end or corner post in a lifeline system Incl. installation set
Request for a quoteABS SAFETY GMBH
Germany
This stainless steel anchorage point (Ø 16 mm), which is cemented into concrete using special adhesive, does not cause any tension to arise in the subsurface and can be implemented in situations where the installation depth is a mere 50 mm. The anchor base plate (200 x 200 mm) is installed on an uncovered surface using the 4 anchor rods supplied. EN 795:2012, A + CEN/TS 16415:2013 Concrete ≥C20/25 Installation depth required: Only 50mm Recommended accessories: Special Adhesive WIT-VM-250 Add a supporting tube for usage as an end or corner post in a lifeline system Incl. stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
You can use this stainless steel anchor on trapezoidal sheeting (positive or negative) either as an anchorage point or for attaching a safety net. The special toggle bolt included in the package comes with its own integrated seal. EN 795:2012, A + EN 1263-2:2014 Sandwich and trapezoidal sheeting (positive/ negative) Steel ≥ 0.75 mm Aluminium ≥ 2.00 mm
Request for a quoteABS SAFETY GMBH
Germany
Thanks to its elongated aluminium base plate, this stainless steel anchorage device can be installed on a fibre cement roof (wave distance 177 mm), if the roof beams measure at least 60 x 120 mm. The device is attached to 2 beams. The base plate, which is 125 cm long when delivered, can be shortened onsite, if required. EN 795:2012, A + CEN/TS 16415:2013 Special wave design, e.g. for Eternit and similar roof systems Designed for load-bearing wooden structures Simply screwed onto two adjacent beams Min. beam dimensions: 60 x 120 mm
Request for a quoteABS SAFETY GMBH
Germany
This easy-to-install stainless steel anchorage point is simply embedded in a concrete surface using a special drive-in dowel (M10). Thanks to its discreet anchorage eyelet, this device, which can be used to secure 1 individual, is virtually indiscernable to the eye following installation. EN 795:2012, A Small and unobtrusive Concrete ≥ C20/25 Incl. stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
Use this temporary anchorage device as a mobile anchor solution. In just a few seconds, the brass clamps of this anchor, which to a large part is manufactured from aluminium, can be clamped to a steel girder. This device, which only weighs 1.85 kg, protects 1 individual from falling. EN 795:2012, B Simply clamped to a steel girder Flange width: 100 - 330 mm Flange depth: max. 33 mm
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
ABS SAFETY GMBH
Germany
The thread (M12) of this stainless steel anchor is screwed through a steel surface (min. 5 mm) and countered accordingly. Alternatively, it can also be screwed into a pre-installed female thread. This anchor, which is capable of restraining loads in all directions, can also be installed overhead, if required. EN 795:2012, A Designed to be screwed to a steel structure or screwed through and countered Installation materials included
Request for a quoteABS SAFETY GMBH
Germany
The thread (M12) of this particularly robust stainless steel anchorage point is permanently installed in concrete using special adhesive. Once installed, it is suitable for all directions of load. You can install it on the ground, in a wall or overhead, depending on your individual needs. EN 795:2012, A Concrete ≥ C20/25 Recommended accessories: Special Adhesive WIT-VM-250
Request for a quoteABS SAFETY GMBH
Germany
This stainless steel anchorage point (Ø 16 mm) has been awarded national technical approval for steel structures. Whatever direction of load is concerned (roof, wall, facade or overhead), it reliably protects your workers from falling . Simply insert the anchor into a pre-drilled bore and counter it using the nut supplied. National technical approval ("abZ"): Z-14.9-688 (pls. observe the installation instructions provided in the "abZ") EN 795:2012, A + CEN/TS 16415:2013 Protruding and non-protruding models available Installation materials included Add a supporting tube for usage as a corner or curve element in a lifeline system
Request for a quoteABS SAFETY GMBH
Germany
This stainless steel anchorage point (Ø 16 mm) for steel surfaces is reinforced through a special supporting tube (Ø 42 mm). You can either use it as a single anchorage point or integrate it into a lifeline system. It is installed laterally using the angular plate supplied and then countered using 2 threaded bolts and corresponding nuts. EN 795:2012, A + CEN/TS 16415:2013 Angular plate for lateral installation Installation materials included
Request for a quoteABS SAFETY GMBH
Germany
This reinforced, stainless steel anchorage point (Ø 16 mm) comes with a special supporting tube (Ø 42 mm) and includes an angular plate for lateral installation. Simply drill 2 holes through a load-bearing beam to install it. Our standard package includes threaded bolts and nuts for countering. EN 795:2012, A + CEN/TS 16415:2013 Angular plate for lateral installation Designed for load-bearing wooden structures Minimum beam dimensions: 100 mm x 200 mm Incl. stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
This stainless steel anchorage point (Ø 16 mm) is attached laterally to a concrete surface. It is reinforced by screwing on the supporting tube supplied (Ø 42 mm) - making it ideal for usage as a stronge support in a lifeline system. Our standard package includes 2 anchor rods and an angular plate - all made of stainless steel material. EN 795:2012, A + CEN/TS 16415:2013 Angular plate for lateral installation Concrete ≥ C20/25 Recommended accessories: Special Adhesive WIT-VM-250 Incl. stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
The angular plate supplied with this stainless steel anchorage point (Ø 16 mm) makes light work of installing it on a steel structure. It can be attached to the structure permanently using the 2 threaded bolts included in the package. These are simply inserted through two pre-drilled bores and countered using the nuts supplied. EN 795:2012, A + CEN/TS 16415:2013 Angular plate for lateral installation 2-hole system for flexible installation Incl. stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
Thanks to its angular bracket, this stainless steel anchorage point (Ø 16 mm) can be quickly and easily installed in a lateral position. The 2 anchor rods included in the package are permanently installed in the concrete subsurface using a special two-component adhesive. Once installed, this anchor is suitable for all directions of load. EN 795:2012, A + CEN/TS 16415:2013 Angular plate for lateral installation 2-hole system for flexible installation Concrete ≥ C20/25 Recommended accessories: Special Adhesive WIT-VM-250 Incl. stainless steel installation set
Request for a quoteABS SAFETY GMBH
Germany
Depending on the subsurface (steel, copper, aluminium or titanium zinc), this stainless steel anchorage point can be installed on a metal roof using either aluminium or brass clamps. It is simply attached to a standing or copper standing seam using the specially-designed clamps supplied - completely penetration-free. EN 795:2012, A + CEN/TS 16415:2013 Freely-rotating anchor eyelet Clamped onto a seam without penetrating your roof surface Mounted on a single seam For steel and stainless steel ≥ 0.5 mm; copper ≥ 0.6 mm; titanium zinc and aluminium ≥ 0.7 mm For Rheinzink and similar systems Incl. installation set
Request for a quoteABS SAFETY GMBH
Germany
Simply clamp this freely-rotating stainless steel anchorage point onto a rounded-edge seam without penetrating your roof surface. As it is only attached to one single seam, you can work with it irregardless of the seam distance. The standard package includes specially-designed aluminium clamps which you can install without having to penetrate the roof membrane. EN 795:2012, A + CEN/TS 16415:2013 Completely penetration-free installation Mounted on a single seam Aluminium depth ≥ 0.8 mm For BEMO and similar systems Incl. installation set
Request for a quoteABS SAFETY GMBH
Germany
This stainless steel anchorage point can be installed on standing seam roofs made of steel, copper, aluminium or titanium zinc without penetrating the roof surface. Depending on the subsurface, this kind-to-your-roof device is attached using the aluminium or brass clamps supplied in the package. EN 795:2012, A + CEN/TS 16415:2017 Clamped onto two adjacent seams - completely penetration-free Seam intervals: 300 - 450 mm / 420 - 660 mm For steel and stainless steel ≥ 0.5 mm; copper ≥ 0.6 mm; aluminium & titanium zinc ≥ 0.7 mm For Rheinzink and similar systems; also suitable for copper standing seam panels (Cu) Incl. installation set
Request for a quoteABS SAFETY GMBH
Germany
Attach this stainless steel anchorage point to the rounded-edge seams of a metal roof using the clamps included in the package - completely penetration-free. Your surface only needs to be 0.7mm thick (aluminium) to install it and protect 3 individuals from falls. EN 795:2012, A + CEN/TS 16415:2017 Clamped onto two adjacent seams - completely penetration-free Seam intervals: 300 - 450 mm / 420 - 660 mm Aluminium thickness ≥ 0.7 mm For BEMO and similar systems Incl. installation set We also supply a protruding model for use in a lifeline system
Request for a quoteResults for
Anchorages - Import exportNumber of results
79 ProductsCompany type
Category