Air spraying - Import export

Extra-strong, compressed air cleaner with practical spray nozzle hard-to-reach places. Flammable. • Extra-strong compressed air cleaner with practical spray nozzle for precise use • Ideal for electronic office equipment and cameras etc. • Best effects when sprayed in short bursts approx. 20 cm away from the object to be cleaned • Flammable • Contents: 400 ml

Compressed air cleaner with practical spray nozzle hard-to-reach places. Non-flammable. • Compressed air cleaner with practical spray nozzle for precise use • Ideal for electronic office equipment and cameras etc. • Best effects when sprayed in short bursts approx. 20 cm away from the object to be cleaned • Non-flammable • Contents: 350 ml

Compressed air cleaner with practical spray nozzle hard-to-reach places. Flammable. • Compressed air cleaner with practical spray nozzle for precise use • Ideal for electronic office equipment and cameras etc. • Best effects when sprayed in short bursts approx. 20 cm away from the object to be cleaned • Flammable • Contents: 400 ml

For removing dust prior to maintenance and repair work, e.g. on magnetic plates, reading heads, audio-visual magnetic tape recording and playback heads, phonograph pick-ups, record turntables or phonograph records For cleaning vacuum sealing surfaces, sealing rings, high-voltage insulators, sample containers etc. For vacuum systems and device groups under clean-room conditions for semiconductor production Cleaning of opto-electronic reading units for bank checks and contactless cleaning of optical devices For maintenance of automated teller machines, quartz clocks or display panels For dedusting precision mechanical parts and assemblies in office machines, copiers, fax machines etc. Advantages and benefits Excellently suited for dedusting, blowing out and blowing off dust and liquids of all kinds Dry, oil-free compressed gas leaves behind no residues Replacement for ultrapure compressed air

Lifetime lubrication of metal-to-metal connections at low to medium rotational speeds and high loads Run-in lubrication in combination with oil or grease lubrication Dry lubrication at sliding pairs, in particular under heavy loads and low sliding speeds, at oscillating movements Dry lubrication at high operating temperatures (up to 450°C) Dry lubrication in dusty environment, to avoid adhesions Advantages and benefits Highly effective due to good adhesion to prepared substrates Allows a low coefficient of sliding friction also under heavy loading Very thin layer thicknesses possible Increased wear protection Rapid curing at room temperature Shortens and improves run-in conditions of friction bearings, toothing and other sliding pairs

Spray nozzle SD 20: numerous application and setting options The SD 20 includes an integrated control valve with which it is possible to quickly and simply control the spray and control air. It is possible to adjust the spray width manually. This model is primarily envisaged for flat spraying tasks; however, round spray application is also an option. It is possible to control the SD 20 pneumatically or electrically.

Oil mist separator Best possible protection against oil and spray mist Clean air – always With our special filter system EONA 3000 you efficiently remove oil mist and oil vapour emitted during lubrication procedures to maintain high air quality at the machine and place of work. Features & benefits • High separation efficiency thanks to the integrated F9 class filter • Several filter stages, which ensures the last filter stage enjoys a particularly long service life • Installed in a sturdy sheet-steel housing • Various “docking sizes” for suction hoses • Controllable ventilator (including remote control) Design versions and details The extremely sturdy filter system EONA 3000 is designed for horizontal extraction. We offer this product suitably sized for all working environments. The extraction capacity of the EONA 3000 is 3000 m3/h. The separated oil is collected or is allowed to drain. An electrostatic extraction filter is available as an optional extra. Moreover, the system is a

Spray walls and spray booths with dry separation via pre-filters and fine filters. Spray walls and spray booths with dry separation For lower utilisation times or overspray quantities, spraying systems with dry separation offer a meaningful alternative to water-sprinkled systems. The Rippert modular spraying system type RTS enables individual adaptation to the respective case of need. Function The overspray is caught by the exhaust air stream and fed to the filter. The solids are filtered out here, while the cleaned exhaust air is blown out into the open air by the fan. Versions The entire spray wall and the drip tray are made of galvanised sheet steel. The basic version consists of a wall with a two-fold filter stage. The attached radial fan is equipped with spark protection in the suction nozzle as well as an explosion-proof motor. The first filter stage is formed by a paper filter or a baffle plate filter, consisting of two rows of galvanised sheet metal lamellae arranged one behind the other. A glass fibre fine filter arranged directly behind it represents the second filter stage. The spray wall can additionally be equipped with removable or fixed side and ceiling panels. Each version is also available with floor suction pan, available with an integrated 2-stage filter and grating cover. Accessories In addition, the spray wall can be equipped with various accessories from the Rippert product range, such as explosion-proof lights, energy-saving flaps, turntables, etc. We recommend the installation of a supply air system for the replacement of the exhausted air. Cleaning / maintenance The spray wall is designed such that the filter elements can be exchanged with little effort in a very short time. For faster cleaning, baffle plate filters should by sprayed with a release agent (e.g. strippable varnish) before being put into operation. Underfloor paint mist extraction With dry separation, consisting of a support structure with attached paper filter, grating cover and a suction duct with air quantity adjustment.

With high-quality filter tubes and PTFE diaphragms. Paint dust filters Wet painting also results in overspray. Overspray is the solid portion of the paint that is not taken up by the workpiece. According to the purpose of use, the overspray is moist and sticky immediately after release. It is captured by the exhaust air stream in the spray booth and fed to a filter. This can be, for example, a baffle plate filter, paper filter, fleece filter, glass fibre filter or also combinations of these. The adhesive effect causes the paint particles to adhere to the contact surfaces of the respective filter medium, as a result of which a good degree of separation is achieved. However, all these filters are storage filters, i.e. the filters clog up more and more during operation and cannot be regenerated. A filter exchange becomes necessary if the exhaust air rate of the spray booth falls below the minimum. This can be very time-consuming under certain circumstances and the work process must be interrupted in order to do it. To make things worse, not only must the filtered and bound paint residues be disposed of, but also the actual filter materials. Such tooling times are not justifiable for automatic, continuous or multi-layer painting processes. Continuous procedures such as automatically cleaned filters are likewise required for this. The humidity and the adhesiveness of the particles to be filtered are thereby the problem. In order to solve this problem, the paint particles should be relieved of their adhesive capability as far as possible whilst still inside the paint booth. Our patented ‘RTS-Rotation’ system is outstandingly well suited for this. The system is comprised of slowly rotating brush rollers, which take up the adhesive paint particles on the surface of the bristles and allow them to dry there. The bristles are automatically regenerated at pre-specified time intervals by combing devices that swing in at the rear of the brush rollers. The dislodged paint residues can then be removed and disposed of either manually during work breaks or automatically during operation. The degree of separation of this system is, however, insufficient to satisfy the environmental protection requirements concerning residual dust content in the exhaust air. A further filter stage is necessary for that. It must be assumed that the paint particles arriving here are to a certain extent still damp and sticky. For this we use special paint dust filters with high-quality filter tubes with PTFE diaphragms. If necessary, precoating agents (auxiliary dust) are used in order to neutralise the adhesive capability of the particles and to keep the dust layer on the filter elements permeable to air. The precoating agent is injected into the raw air pipe by means of special dosing units. The filter tubes are cleaned by means of compressed air impulse cleaning. The use of this technology requires special know-how. We have had the appropriate experience for almost ten years. The implemented plants have capacities ranging from 5,000 to 90,000 m³ /h. Because of the large number of different paint systems, individual experiments are usually necessary in our pilot plant in order to find the correct solution for the individual case.

The brand-new PPJ system impresses not only with its well-conceived components and size but also with its innovative form. In this system, we have combined our decades of experience in an attractive design. The independent regulation of fluid and spray air pressure achieves excellent results even with higher-viscosity media. Available for up to 6 spray heads and in versions with 1, 3 and 5 litres, this system has a very compact design and therefore takes up extremely little space when installed. The system is suitable for the initial equipment of machines as well as for subsequent installation. The PPJ system can be used with our spray heads (starting on p. 20) and the JOP drip-feed dosing device (p. 30) up to a maximum viscosity of 2300 mm²/s at 20 °C or 500 mm²/s at 40 °C (except for substances containing paint, resin and glue).

To conform to market requirements, widely differing machines for painting/coating mouldings, window parts and other profile components were developed. The type and number of guns depends both on the paint system and on the quality envisaged. Air, Airmix or Airless spraying systems can be used for this purpose. The individual machine types can be configured with all conveyor systems of our portfolio and combined with the respective drying systems. The difference between the VEN SPRAY MOULD (LT) and (LW) variants is their type of extraction. LT stands for dry extraction, LW for water-backed extraction. VEN SPRAY MOULD COOLAC is exclusively designed for processing water-based paints. The overspray is constantly collected and condensed in chilled collector systems. The condensation of the controlled air humidity keeps the collector devices and chilled conveyor systems permanently wet. This reliably prevents paint particles from drying during operation. The strip painting plants can be supplemented by further Venjakob plant technologies specifically tailored to the process such as brush sanding/denibbing machines, dryers or conveying equipment.

Combination SRK AS + SRK AE Mobile, compact, transportable by car. Without tankWater supply either via suction unit or external water connection. Filter unit with de-airing system. Stepless adjustable pressure. spray volume : 1,8l/min. 10KW, 16A. Start/stop via spray pistol. 5 m hose with quick change lance SR-LA 600, 5m suction hose.

Mobile, compact, transportable by car. Without tank, medium supply via suction unit. No metering of cleaning agent. Stepless adjustable pressure. Filter unit with de-airing system. Start/stop via spray pistol. 5 m hose with quick change lance SR-LA 600, 5m suction hose. 10 KW, 16A.

SCHÜTZE spray valve GF / 3 Designed for spraying colours, paints etc. With integrated atomizing air valve for regulation of purging air. Spray angle can be regulated individually from round- to flatspray without changing the aircap. nozzle and needle: stainless steel available nozzle dimensions: 0,3; 0,5; 0,8; 1,0; 1,2; 1,5; 1,7; 2,0; 2,5; 3,0; 3,5 mm ø Also available in HVLP-technique