Results for
NORELEM FRANCE
France
Bearing block and carriage aluminium alloy. Guide column and threaded spindle stainless steel. Plain bearing for guide columns and spindle nut highquality special plastic. Claw coupling aluminium with polyurethane coupling spider. Version Aluminium alloy anodised. Stainless steel hardened and ground. Threaded spindle with ball bearing. Note for ordering The unit is supplied with the position of cable outlet or control unit as shown in the drawing. Note Positioning stages for motorised adjustment and positioning tasks. The plain bearings and spindle nuts are suitable for dry running, however lubrication with a grease for plastic plain bearings is recommended. The suitable programming software and interface cable for the stepper motor with positioning control are available as accessories (2500015).
Request for a quoteNORELEM FRANCE
France
Universal joints with plain bearing can be swivelled by 45°. Max. transferable torque (Nm) at 150 rpm, operation angle α < 5°. * Bore depth is less than by DIN 808.
Request for a quoteNORELEM FRANCE
France
Housing anodised aluminium. Bearing surface Frelon (Teflon plus proprietary fillers). Virtually chemically inert. Selflubricating (no additional lubrication required). High temperature range (240 °C to +260 °C). Dampens vibrations. High static load capacity projected surface area x P (P = 1034 N/cm²) Suitable for food, pharmaceutical, medical and chemical applications. Insensitive to dirt.
Request for a quoteNORELEM FRANCE
France
Highperformance polymer iglidur® G, iglidur® J or iglidur® X. Version iglidur® G grey; iglidur® J yellow; iglidur® X black Note Plastic highperformance polymer plain bearings. – maintenancefree – lubricantfree – corrosionresistant – resistant to dirt – high dimensional precision – high pressure resistance – good heat dissipation – very low creep tendencies – high mechanical damping – resistant to UV radiation. Assembly The bearings are designed for press fits in H7 bores. After pressing in, the ID of the bearing will be diameter D with the relative tolerance. The bearings are suitable for shafts with h tolerance (recommended min. h9).
Request for a quoteNORELEM FRANCE
France
Selflubricating. Hardness 190220 HB. Note The guide bushes are radially and axially applicable. The bearing elements are maintenancefree and wearresistant. The graphite inserts provide lifelong lubrication. Preferably for travel speeds < 0.5 m/s. (Additional lubrication is recommended for extreme loading with a higher travel speeds). Temperature range Temporary temperature peaks up to ca. 200°C. Tolerances The bore for the bearings should correspond to ISO tolerance H7. The tolerance h6 to h7 is recommended for the shaft.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
Housing igumid® G. Swivel ball iglidur® W300 Note The ability to pivot allows pillow block bearings to compensate for misalignment and possible shaft deflection. They are easy to install and suitable for the accomodation of rotating, oscillating and linear movements. igubal® pillow block bearings are maintenance free and conceived for dry running condition. Assembly These pillow block bearings are designed for mounting with 2 screws. The ID tolerance is E10. The matching shaft should have a tolerance of h6 to h9.
Request for a quoteNORELEM FRANCE
France
Aluminium outer ring and inner ring. Iglidur® J plastic slide elements. Stainless steel A2 screws. Version Anodised outer ring and inner ring. Note Aluminium plain bearings with replaceable, high performance material glide elements for rotary stages. Such a combination of materials guarantees absolutely lubricant and maintenancefree running. Simple assembly. High wear resistance. For high loads, high rigidity.
Request for a quoteNORELEM FRANCE
France
Housing plastic. Ball bearing stainless steel 1.4112. Plain bearing insert POM. Bushes and grease nipple stainless steel 1.4301. Version Plain bearing insert white. Housing green. Stainless steel parts bright. Note The housings are very robust, hard wearing and shock proof. They are resistant to most alkaline solutions, weak acids (PH 49) and brines. In contrast to cast or steel housings the special plastic in these housings prevent the formation of microorganisms. Drawing reference 1) ball bearing 2) plain bearing
Request for a quoteNORELEM FRANCE
France
Fitted with smoothrunning plain bearings. Not suitable for swivelling while under load. When lifting the load, the safety latch closes automatically and is securely locked by a locking mechanism at the rear of the hook. To open the latch, the locking mechanism must be unlocked manually. The swivel hooks correspond to the Machinery Directive and are BG certified (H stamp). Temperature range From 40°C to 200°C = 100% permissible load Up to 300°C = 90% permissible load Up to 400°C = 75% permissible load
Request for a quoteNORELEM FRANCE
France
Material: Housing steel plate. Wheels with thermoplastic rubber tread. Wheel body polypropylene. Version: Housing press formed. Double ball bearing in the castor head. Plain bearing in wheels. Note: Wheel axle threaded. Swivel and fixed castors with bolt hole. Electrically conductive wheels, non-marking grey. The ohmic resistance of the wheel is less than 10⁴Ω. Application: Electrically conductive wheels on swivel and fixed castors are used to protect against electrostatic discharge generated by transport equipment or the transported goods. Damage to sensitive goods and painful electrostatic shocks to the personal is so prevented.
Request for a quoteNORELEM FRANCE
France
Sliding carriage Base structure in extruded section, aluminium EN AW6060. Sliding elements Maintenance free plain bearing iglidur® J. Version Eloxalcoated E6/EV1. Black thermoplastic Note With a low rate of inerita, high accelerations and short term extreme speeds up to 30 m/s are possible. DryLin® T linear glide guides are resistant to dirt and corrosion and are adjustable, maintenancefree and quiet. Application temperature max. 80 °C. As no lubricants are used they are recommended for use in food, medical, and clean room technologies. Manual clamping was developed for simple functions. Polymer under constant pressure has a tendency to creep which causes a decrease in clamping force over time (up to 70%), which means that no safetyrelevant parts should be clamped. Suitable guide rails see 21200. Drawing reference 1) manual clamping
Request for a quoteResults for
Plain bearing - Import exportNumber of results
12 ProductsCompany type