Interlock - Import export

Fasten the floating clamp to the fixture with the M12 screw. Adjust the height stop and the swivel range using the blue sleeve and lock with the 3x2.5 mm grub screws. When setting the height leave generous clearance above. For safe operation the M12 tapped hole must always be closed. For specific clamping applications the standard jaws can be altered or replaced. Form B: Fasten the floating clamp with M6 fastening holes to a fixture. Adjust the height stop and pivot range using the blue adjusting sleeve and clamp with grub screws (4x AF 2.5). When setting the height limit, allow ample play at the top. For specific clamping situations, the standard jaw plates can be modified or replaced.

Contactless "door lock" encoded detection Contactless "door open / closed" detection Unlock command with just one contact during serialization of products Emergency evacuation handle • Level of performance with AWAX controller: up to PL = e Safety category with an external controller: up to 4 • Cycle before dangerous failure: B10d = 1,000,000 • Bolt travel: 14 mm • Bolt diameter: 24 mm (beveled for "under-voltage" closed position or "lock" mode) • Shearing strength: 2000 N • Gap between strike and lock: 2 to 4 mm (adjustable when assembling, recommended to 4 mm) Maximum lateral offset between strike and lock: +/- 2.5 mm • Maximum angular displacement between strike and lock: +/- 5° • Safety locking contacts: 2 x NO 2A/50V • Safety door contacts: 2 x PNP/500 mA • Unlock command: PLC-compatible (12~30 VDC/2~5 mA) • Fault Diagnosis: bolt stuck, power out of specification, temperature out of specification, electromagnet failure, serialization failure • Reset: on command • "SMART consumption" for minimal power consumption when connected in series • Auxiliary release: female triangle key 8 mm x 14.2 mm (optional) • Attachment: 4 M6 screws (screw covers supplied, screws not included) • Mounting position: 2 (door pulling, door pushing) • Material: PA6 fiberglass reinforced • Electrical connection: very resistant 50 cm PUR UL20549 cord with M23 connector or cable (contact us) • Water resistance: IP 65 • Operating temperature: -15°C to +45°C • Marking: screen printed + serial no. for traceability • Reference for evacuation handle: AT

Contactless "door lock" encoded detection Unlock command with just one contact during serialization of products • Cycle before dangerous failure: B10d = 1,000,000 at 200mA • Bolt travel: 9 mm • Bolt diameter: 12 mm • Shearing strength: 1000 N • Distance between latch and lock: 0 to 4 mm (adjustable when assembling, recommended to 4 mm) • Maximum lateral displacement between strike and lock: +/- 0.8 mm • Maximum angular displacement between strike and lock: +/- 5° • Safety locking contacts: 2 x NO 0.4A /24V redundant and • Unlock command: PLC-compatible (12~30 VDC/2~5 mA) • Diagnostic error: Auxiliary output indicates unlocking • Reset: on command • Infinite automatic offset control when connected in series: minimal consumption • Auxiliary release: key supplied (free key in lock mode; captive key in release mode) • Attachment: 4 M4 screws (screw covers included) • Mounting position: 1 • Material: PA6 fiberglass reinforced • Electrical connection: very resistant 50 cm or 130 cm PUR UL20549 cord with M12 connector or cable (contact us) • Water resistance: IP 65 • Ambient temperature: -5°C to +40°C. • Marking: screen printed + serial no. for traceability

NF EN ISO 14119 provides measures restricting the possibility of reasonably foreseeable fraudulent neutralization on locking devices. Some drawbacks The key does not provide inviolability. This system has problems related to minimum radius, alignment and breakage when operating the key. The switch often has only one door position contact and two locking contacts. For maximum performance level PL = e, a position sensor must be added with redundant outputs. This overburdens the wiring, occupying 4 inputs on a safety PLC.