Results for
NORELEM FRANCE
France
Ceramic bearings Si3N4. Bearing cage PTFE. For most applications Si3N4 is the preferred material for ceramic bearings. Silicon nitride bearings are light, very hard and highly wear resistant. High and ultrahigh performance bearings are used in e.g. aerospace technology, metal production industries (high application temperatures), machine manufacturing, chemical industries (chemically aggresive substances), pharmaceutical and medical industries, semiconductor and biotechnology (clean room enviroments which may not be contaminated by lubricants). On request Special version with PEEK ball cage. Without ball cage.
Request for a quoteNORELEM FRANCE
France
Ball lock pins are used for easy fastening or joining of components or workpieces. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. Release the button to lock the balls and secure the connection. Form A is suitable for applications where high demands and precision are required. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application. Different materials in which the ball lock pins are used, weather conditions and wear can influence the determined values.
Request for a quoteNORELEM FRANCE
France
Shell, ballbearing steel. Cage, plastic. Balls, steel. Note With seals both ends. The linear ball bearing is secured using DIN 471 / 472 circlips. Application Suitable for applications where installation space is limited.
Request for a quoteNORELEM FRANCE
France
Workpieces are clamped and released by compressed air. The possible clamping diameter is from 16 to 20 mm. Material: Body, stainless steel. Seal, NBR. Version: Stainless steel bright. Note for ordering: Cylinder head screws M4X35 for fastening from below are included with delivery. Cylinder head screws with low head M5 for fastening from above are not included with delivery. Note: Installed dimensions for plate thickness 6 mm. The stated retaining forces are related to an operating pressure of 0.5 Mpa and a surface quality of Ra 1.6 µm. Repeat accuracy in this case is ±0.2 mm.
Request for a quoteNORELEM FRANCE
France
Housing hardened and black oxidised. Contact faces ground. Note: Locating bushes are placed in a fixture or interchangeable subplate and form the counterpart to the locating cylinder. The locating bushes are centred in a reamed hole and then fastened with 4 screws. The balls of the locating cylinder engage in the groove in the locating bush, thereby forming a fast, secure and highly accurate changeover unit, and reducing setup and changeover times. Attention: Please observe installation notes of the locating bushes.
Request for a quoteNORELEM FRANCE
France
Housing hardened and black oxidised. Contact faces ground. Note: This positioning and clamping system is especially suitable for installation in fixtures (plates, clamping tower blocks, etc.) in all mounting positions. The modular design allows the number of and distance between the locating cylinders to be ideally adjusted to suit the clamping task. Due to the small diameters, the spacing between the locating cylinders can also be reduced. The 3 clamping balls are mechanically released through control of the locating cylinder with the "opening" connection. The 3 clamping balls move inward and the fixture can be changed quickly. For clamping, the air is taken from the "opening" connection and the "clamping" connection then receives air on the locating cylinder. The 3 clamping balls are mechanically driven outward again and the new fixture is clamped. To achieve optimal retaining force, the locating cylinder remains connected to the air.
Request for a quoteNORELEM FRANCE
France
Locating cylinder tempered, black oxidised. Balls hardened, bright. Note: Locating cylinder with quick-clamp system for extra timesaving during setups. Insert the locating cylinder into the receiving hole and press the button. The three balls are pushed out and position the components. By tightening the set screw a 1/4 turn using an hexagonal key, the components are positively and securely held.
Request for a quoteNORELEM FRANCE
France
Ball-end thrust screws with full ball are used when a clean, polished contact surface is required.
Request for a quoteNORELEM FRANCE
France
Steel. Version: Ball thrust pins trivalent passivated. Ball seat and nuts electro zinc-plated. Note: Axial joint suitable for taking up tractive forces. The ball's movement can be controlled or fully locked in position using the clamping nut.
Request for a quoteNORELEM FRANCE
France
Sprockets with hub one side for DIN ISO 606 roller chains. The sprockets have a centre bore or are predrilled (this can vary due to production methods). For this reason, the dimension D3 max. given in the table is the maximum diameter of the bore that the sprockets are supplied with. This pilot hole/centre bore can be customised with a reamed hole, reamed hole with keyway or a tapped hole by the customer. Alternatively, bushes can be fitted by the customer to reduce the diameter.
Request for a quoteNORELEM FRANCE
France
Housing plastic. Ball bearing stainless steel 1.4112. Plain bearing insert POM. Bushes and grease nipple stainless steel 1.4301. Version Plain bearing insert white. Housing green. Stainless steel parts bright. Note The housings are very robust, hard wearing and shock proof. They are resistant to most alkaline solutions, weak acids (PH 49) and brines. In contrast to cast or steel housings the special plastic in these housings prevent the formation of microorganisms. Drawing reference 1) ball bearing 2) plain bearing
Request for a quoteNORELEM FRANCE
France
Housing, stainless steel 1.4301. Bearing, stainless steel 1.4125. Seal, rubber NBR. Note Pillow block bearings consist of a sealed singlerow ball bearing with a spherical outer ring which is mounted in a housing. Because of the spherical outer surface of the bearing, shaft misalignment can be compensated for. The bearings are manufactured with a plus tolerance. This results in transition or press fits when using shafts with htolerances. The shaft is secured by grub screws on the inner ring. In normal applications, pillow block bearings are maintenancefree due to the lifetime lubrication. In difficult environmental conditions relubrication can be carried out over the grease nipple. All housing dimensions are nominal dimensions for which the usual casting tolerances must be taken into consideration.
Request for a quoteNORELEM FRANCE
France
Material Ballbearing steel 100Cr6. Seal, rubber NBR. Version Sealed on both sides with a spherical outer ring. Can be relubricated. Note The internal construction of the insert bearings corresponds to that of standard Series 6200 and 6300 radial ball bearing. However, they have wider inner rings for easier fastening on shafts. The inner rings are manufactured with a plus tolerance. This results in transition or press fits when using shafts with htolerances. The shaft is secured by 2 grub screws positioned 120° apart on the inner ring. The insert bearings are ready to install and are permanently lubricated with a suitable ball bearing grease. In normal applications, relubrication is not necessary.
Request for a quoteNORELEM FRANCE
France
Housing, grey cast iron. Bearing, ballbearing steel 100Cr6. Seal, rubber NBR. Pillow block bearings consist of a sealed singlerow ball bearing with a spherical outer ring which is mounted in a housing. Because of the spherical outer surface of the bearing, shaft misalignment can be compensated for. The bearings are manufactured with a plus tolerance. This results in transition or press fits when using shafts with htolerances. The shaft is secured by grub screws on the inner ring. In normal applications, pillow block bearings are maintenancefree due to the lifetime lubrication. In difficult environmental conditions relubrication can be carried out over the grease nipple. All housing dimensions are nominal dimensions for which the usual casting tolerances must be taken into consideration.
Request for a quoteNORELEM FRANCE
France
The axis height of the spindle bearings matches the fixed bearing unit 2407801. The floating bearing units consist of a housing with deep groove ball bearing, which adapts axially to the linear expansion of the spindle.
Request for a quoteNORELEM FRANCE
France
Housing washer, shaft washer and rolling elements, bearing steel. Cage, steel. Note Axial ball bearings accept high axial loads from one direction but may not be loaded radially. The bearings are separable. This means the bearing parts can be fitted independently of each other. The main dimensions of the axial ball bearing conform to ISO 104 and DIN 711. Dimensional and running tolerances correspond to tolerance class PN acc. to DIN 620. These tolerance classes are standard and are well suited for most applications.
Request for a quoteNORELEM FRANCE
France
Steel housing. Nitrile rubber seal. Preloaded highaccuracy bearings with a 60° thrust angle. The bearings accept both radial and axial forces from both directions. Due to their preload, the angular contact ball bearings provide a high level of stiffness, excellent concentricity, precise tool positioning and repeatability. The integrated lowfriction seal effectively keeps dirt away from the bearing, thereby ensuring excellent operating safety and a long service life. The bearing friction coefficient Mrl is a reference value. The moment of inertia corresponds to that of the rotating inner ring. The limiting speeds are applicable after grease is applied. Technical data All bearings are supplied ready for mounting with lubricating grease type KE2P35 acc. to DIN 51825. Housing and shaft tolerances correspond to roundness tolerance class IT2 and perpendicularity tolerance class IT4.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
Steel. Toothed pulleys without aluminium rim flanges. Version Steel phosphated. Aluminium bright. Note Standard HTD profile with metric pitch (halfround toothing). At least one belt pulley must have a rim flange. The toothed belt pulleys have a centre bore or a pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the toothed belt pulleys are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter. The pulleys may be recessed on the sides.
Request for a quoteNORELEM FRANCE
France
Aluminium. Rim flanges, steel. Version Aluminium bright. Steel electro zincplated. Note Standard T profile acc. to DIN 7721 T2 with metric pitch (trapezoidal toothing). At least one belt pulley must have a rim flange. The toothed belt pulleys have a centre bore or a pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the toothed belt pulleys are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter.
Request for a quoteNORELEM FRANCE
France
Polyethylene PEUHMW (ultrahigh molecular weight polyethylene). Glide rails for roller chains as defined in DIN ISO 606. These support and guide the roller chains on the return side, thus extending useful life by significantly reducing wear on the roller chains. They reduce vibrations and noise in the chain drive. These glide rails have high abrasion and wear resistance. They are maintenancefree, acidproof and have high chemical resistance. The additional C profiles are used for fastening to the system substructure and they protect the glide rails from lateral forces and torsion. Assembly The glide rails are pushed into the C profiles fastened to the system. The glide rails must be mounted so that the material is allowed to expand. A property of thermoplastic materials is that they expand or contract more than metals when there are temperature variations.
Request for a quoteNORELEM FRANCE
France
Sprocket steel. Ball bearing chrome steel. Screw and nut steel. Version Sprocket teeth hardened to HRC 50, electro zincplated. Ball bearing with sealing discs 2ZC3. Screw ISO 4017, grade 8.8, electro zincplated. Nut ISO 4035, grade 8, electro zincplated. Note For tensioning roller chains. The sprocket set can be combined with all tensioning elements to form a readytoinstall chain clamp. The ball bearings are sealed both sides, permanently lubricated and maintenancefree. The sprocket can be moved on the screw and thus adapted to the chain track. With the duplex and triplex version, precision spacer sleeves ensure correct chain guidance. Rigid mounting without a tensioning element is also possible. Can also be used as an idler sprocket.
Request for a quoteNORELEM FRANCE
France
The readytoinstall compact linear housing consists of extruded aluminium housing, installed linear ball bearing 2151102 and doublesided seal. Recommended shaft tolerance h6. Load rating according to specification of the linear ball bearing. With lubrication hole M8x1. Accessory Precision guide shafts 21595. Fastening screws 07160.
Request for a quoteNORELEM FRANCE
France
Housing steel. Cage plastic. Balls steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seal. The linear ball bearings have a plastic cage which results in quiet and outstanding running properties. With flange for direct mounting on the housing. Linear ball bearings with doublesided seal should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts. Precision guide shafts 21595. Fastening screws 07160.
Request for a quoteNORELEM FRANCE
France
Outer jacket stainless steel. Cage stainless steel. Balls stainless steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seals and a stainless steel cage. The bearing is secured with DIN 471/472 circlips. Linear ball bearings with doublesided seals should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts.
Request for a quoteNORELEM FRANCE
France
Sold in pairs. Fastening material included. Note As an option for floor, platform or side mounting.
Request for a quoteNORELEM FRANCE
France
Slides stainless steel 1.4301. Ball cage stainless steel 1.4301. Balls stainless steel 1.4034. Version Slides bright. Ball cages bright. Balls bright. Note for ordering Sold in pairs. Note On telescopic slides with overextension, the travel is greater than the installed length. Latches in open position. When the release lever is actuated, the drawer can be taken out easily and separated from the guide. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 400 mm and is based on the maximum value with 10,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide.
Request for a quoteNORELEM FRANCE
France
Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note On telescopic slides with partial extension both sides, the travel is less than the installed length. Latches in open position on both sides. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 50,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide. Advantages Pulls out in both directions Latches in open position on both sides Light running
Request for a quoteNORELEM FRANCE
France
Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note By telescopic slides with full extension, the travel is roughly equal to the installed length, which ensures greater comfort and accessibility. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 80,000 cycles. Not suitable for horizontal mounting. The head height of the fastening screws should not exceed 1.8 mm otherwise there is a risk of collision with other parts of the slide. Advantages Low slide thickness Light running Precise guidance for high lateral stability
Request for a quoteNORELEM FRANCE
France
Race body steel. Wipers plastic/felt. Longitudinal sealing lips rubber. Rollers steel 1.3505. Note Roller carriage with lifetimelubrication roller bearings and wipers which lubricate the system when moving. By simply moving the centre cam roller, the roller carriage can be adjusted so that it is free of play or has the desired pretension in the rail. High travel speeds up to 7 m/s and extremely quiet (faster and quieter than systems that use recirculating balls). The wipers are fitted with an oilsoaked felt. This felt is in constant contact with the track to ensure perfect lubrication. The felts can be recharged using an oil pump through the lubrication points on the front. On request Roller carriages with 4 or 5 rollers.
Request for a quoteResults for
Balls - Import exportNumber of results
53 ProductsCompany type