Push-pulls - Import export

Contactless "door lock" encoded detection Contactless "door open / closed" detection Unlock command with just one contact during serialization of products Emergency evacuation handle • Level of performance with AWAX controller: up to PL = e Safety category with an external controller: up to 4 • Cycle before dangerous failure: B10d = 1,000,000 • Bolt travel: 14 mm • Bolt diameter: 24 mm (beveled for "under-voltage" closed position or "lock" mode) • Shearing strength: 2000 N • Gap between strike and lock: 2 to 4 mm (adjustable when assembling, recommended to 4 mm) Maximum lateral offset between strike and lock: +/- 2.5 mm • Maximum angular displacement between strike and lock: +/- 5° • Safety locking contacts: 2 x NO 2A/50V • Safety door contacts: 2 x PNP/500 mA • Unlock command: PLC-compatible (12~30 VDC/2~5 mA) • Fault Diagnosis: bolt stuck, power out of specification, temperature out of specification, electromagnet failure, serialization failure • Reset: on command • "SMART consumption" for minimal power consumption when connected in series • Auxiliary release: female triangle key 8 mm x 14.2 mm (optional) • Attachment: 4 M6 screws (screw covers supplied, screws not included) • Mounting position: 2 (door pulling, door pushing) • Material: PA6 fiberglass reinforced • Electrical connection: very resistant 50 cm PUR UL20549 cord with M23 connector or cable (contact us) • Water resistance: IP 65 • Operating temperature: -15°C to +45°C • Marking: screen printed + serial no. for traceability • Reference for evacuation handle: AT

This pack consists of 20 x painted aluminum manual formwork panels 3m x 1m 40 × GP10 single or variable alignment flange 33 × Tightening rod 750 cmm DW15 + 2 nuts DW15 2 × GP10 lifting hooks 5 × Double push pull props GP10 5 × Blocker consoles

This pack consists of - 20 x modular painted steel formwork panels 3m x 1m - 40 × GP10 single or variable alignment flange - 33 × Tightening rod 750 cmm DW15 + 2 nuts DW15 - 2 × GP10 lifting hooks - 5 × GP10 double push pull prop - 5 × Service consoles with blockers

10 x modular painted steel formwork panels 3m x 2m 20 × Single or variable GP10 alignment flanges 20 × Tightening rod 750 cmm DW15 + 2 nuts DW15 2 × GP10 lifting hooks 5 × Double push pull props GP10 5 × Service consoles with blockers 1 x Inside angle H: 3m, 0.30x0.30 m 1 x painted steel modular formwork panel 0.60 x 3m 1 x painted steel modular formwork panel 0.50 x 3m 2 × Compensation 3000 x 100 mm 2 × Compensation 3000 x 50 mm 3 × Variable angle flanges GP10 8 × GP10 Variable Alignment Flanges 1 x Accessory box 120x80

-20 x modular painted aluminum manual formwork panels 3m x 1m - 40 × GP10 single or variable alignment flanges - 33 × Tightening rod 750 cmm DW15 + 2 nuts DW15 - 2 × GP10 lifting hooks - 5 × GP10 double push pull prop - 5 × Service consoles with blockers - 1 x Inside angle H: 3m, 0.30x0.30 m - 1x manual painted aluminum modular formwork panel 0.60 x 3m - 1 x painted aluminum modular panel 0.50 x 3m - 2 × Compensation 3000x100 mm - 2 × Compensation 3000x50 mm - 3 × Variable angle flanges GP10 - 8 × Variable alignment flanges GP10 - 1 x Accessory box 120x80

This pack consists of -20 x painted steel modular formwork panels 3m x 1m - 40 × GP10 single or variable alignment flanges - 33 × Tightening rod 750 cmm DW15 + 2 nuts DW15 - 2 × GP10 lifting hooks - 5 × GP10 double push pull prop - 5 × Service consoles with blockers - 1 x Inside angle H: 3m, 0.30x0.30 m - 1x of modular painted steel formwork 0.60 x 3m - 1 x painted steel modular formwork panel 0.50 x 3m - 2 × Compensation 3000x100 mm - 2 × Compensation 3000x50 mm - 3 × Variable angle flanges GP10 - 8 × Variable alignment flanges GP10 - 1 x Accessory box 120x80