Results for
NORELEM FRANCE
France
Highperformance polymer iglidur® G, iglidur® J or iglidur® X. Version iglidur® G grey; iglidur® J yellow; iglidur® X black Note Plastic highperformance polymer plain bearings. – maintenancefree – lubricantfree – corrosionresistant – resistant to dirt – high dimensional precision – high pressure resistance – good heat dissipation – very low creep tendencies – high mechanical damping – resistant to UV radiation. Assembly The bearings are designed for press fits in H7 bores. After pressing in, the ID of the bearing will be diameter D with the relative tolerance. The bearings are suitable for shafts with h tolerance (recommended min. h9).
Request for a quoteNORELEM FRANCE
France
Selflubricating. Hardness 190220 HB. Note The guide bushes are radially and axially applicable. The bearing elements are maintenancefree and wearresistant. The graphite inserts provide lifelong lubrication. Preferably for travel speeds < 0.5 m/s. (Additional lubrication is recommended for extreme loading with a higher travel speeds). Temperature range Temporary temperature peaks up to ca. 200°C. Tolerances The bore for the bearings should correspond to ISO tolerance H7. The tolerance h6 to h7 is recommended for the shaft.
Request for a quoteNORELEM FRANCE
France
Exceptionally wearresistant Dimensionally stable even at high temperatures Electrically insulating Frequency neutral
Request for a quoteNORELEM FRANCE
France
Housing igumid® G. Swivel ball iglidur® W300 Note The ability to pivot allows pillow block bearings to compensate for misalignment and possible shaft deflection. They are easy to install and suitable for the accomodation of rotating, oscillating and linear movements. igubal® pillow block bearings are maintenance free and conceived for dry running condition. Assembly These pillow block bearings are designed for mounting with 2 screws. The ID tolerance is E10. The matching shaft should have a tolerance of h6 to h9.
Request for a quoteNORELEM FRANCE
France
Universal joints with plain bearing can be swivelled by 45°. Max. transferable torque (Nm) at 150 rpm, operation angle α < 5°. * Bore depth is less than by DIN 808.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
Body and flange plate EN AW5754. Guide shafts steel Version Body, hardcoated Flange plates, anodised. Guide shaft, hardened. Note Maintenancefree pneumatic linear modules with two precision steel shafts and ball guide bushing with wipers. Double acting cylinder drive. All fastening threads have threaded inserts. The as accessory available shock absorbers and proximity switches can be integrated (no protruding edges). Positive fit construction for hundred per cent reproducibility. Combinations in all sizes and stroke variants are feasible without adapter plates. Repeat accuracies of ±0.01 mm are possible. Specified loads apply by centred carriages. On request Available with locking cartridge as stroke deviation safeguard. Accessory See table for shock absorber, proximitiy switch and plug connector.
Request for a quoteNORELEM FRANCE
France
These precision slideways with roller bearings are used in machine and fixture construction, metrology, optical instruments and precision mechanics. The scale division on the micrometer dial is 0.02 mm. The stated permissible load values (F) are designed for a service life of 1 million travel cycles. The torque values apply only to centred slides. An additional centring hole is located at holes D2 and D3 on the top of the slide. Other connecting elements can be precisely mounted on the slide in combination with our centring rings 20240. F = permissible loading for dynamic and static loads. TI E/E1 = number of fastening holes E/E1/M inside. TA E/E1 = number of fastening holes E/E1/M outside. TI E4 = number of fastening holes E4/D1 inside. TA E2 = number of fastening holes E2/D1 outside.
Request for a quoteNORELEM FRANCE
France
These precise slideways are used in e.g. machine, fixture and metrology equipment construction as well as in the optical and precision engineering industries. The central set screw M1 can be replaced by a clamping lever 06460. The stated permissible load values (F) are designed for dynamic loads with a service life of 1 million travel cycles. For static loads, 10 times the table value F is permitted. The torque values apply only to centred slides. An additional centring hole is located at holes D2 and D3 on the top of the slide. Other connecting elements can be precisely mounted on the slide in combination with our centring rings 20240. TI E = number of fastening holes E/M inside. TA E = number of fastening holes E/M outside. TI E1 = number of fastening holes E1/D1 inside. TA E1 = number of fastening holes E1/D1 outside.
Request for a quoteNORELEM FRANCE
France
These precision dovetail slides find use in e.g. machine and fixture construction, metrology, optical instruments and fine mechanics. The stated permissible load rating (F) is for static loads. The torque values only apply for centred carriages. TI = number of fastening holes E1/E2/MI inside. TA = number of fastening holes E/E1/MA outside. TM = number of centring holes D1 inside. TN = number of centring holes D1 outside. Advantages An additional centring hole is located at all tapped holes. Other connecting elements can be precisely mounted on the slide in combination with our centring rings 20240. Quick and retrofit combination in the X, Y and Z axes.
Request for a quoteNORELEM FRANCE
France
Elastomer spider polyurethane Shore 98A. Coupling housing and clamping hub, aluminium. Expanding mandrel steel. Screws steel. Centring rings 1.4301 stainless steel. Version Coupling housing black anodised. Note The motor adapter set with elastomer dog coupling system (elastomer coupling with expanding mandrel) provides a simple and costeffective solution for connecting electric motors. Advantages of the elastomer dog coupling Hub with expanding mandrel can be mounted axially Playfree with vibration absorption Excellent retaining force Excellent concentric accuracy Short design Easy to assemble Can be mounted axially on spigot side Electrical insulation Nominal torque up to 30 Nm On request Larger hub bore D. Higher nominal torque.
Request for a quotePOUGET
France
1 - Reinforced Extension Bar length 200 mm - Drive female square 25.4 mm Outdrive male square : 25.4 mm - Ref. 13LC - Weight 1.64 Kg Outdrive male square : 23 mm - Ref. 14LC - Weight 1.63 Kg 2 - Reinforced Extension Bar length 330 mm - Drive female square 25.4 mm Outdrive male square 25.4 mm - Ref. 9LC - Weight 2.55 Kg Outdrive male square 23 mm - Ref. 15LC - Weight 2.54 Kg 3 - Universal Joint - length 110 mm, permet le serrage et le dressage des boulons d'éclisses. Outdrive 25.4 mm - Ref. 10LC - Weight 1.04 Kg 4 - Sleeper Drilling Accessory (for drills with cylindrical shank Ø 16 mm) 1) Drive by female square 25.4 mm with a quick fitting on balls, length 160 mm - Ref. ATB - Weight 1.6 Kg with tightening of drill by screw length 140 mm - Ref. 8LC - Weight 1.38 Kg 2) Drive by Morse No. 3 Cone with a quick fitting on balls, length 200 mm - Ref. 16LC - Weight 1.3 Kg 5 - ROISSY Cutter equipped complete - Ref. FR-16 - Weight 0.77 Kg for drilling maxi Ø 80 mm (adjustable) Total length
Request for a quoteResults for
Universal joints - Import exportNumber of results
12 ProductsCompany type
Category