Results for
France
The Dusty C has been specially developed to monitor clean sides after filters with high reliability and without time delay for filter breaks. It can be used in metallic ducts in which dust particles will be detected in the gas flow. Its area of application begins at dust levels of 0.1 mg/m3. • detects all dust types • can be used in all purge gas and dust ducts • immediate detection of filter damages • simple commissioning (plug & play) • can be used in ex zones • individual choice of alarm level • rapid and easy retrofitting
Request for a quoteFrance
Microwave barrier for contactless detection of dry bulk solids with fillingsignalsuppression in containers or chutes. Reliable fill level and limit level detection. • indicates level and material flow • with filling signal recognition • up to 1,000 °C possible with ceramic mounting • insensitive to material caking • usable for profiles up to 25 m • no measurement failure due to strong material flow for filling
Request for a quoteFrance
Microwave sensor for continuous moisture measurement in dry bulk solids, with flow detection and process temperature measurement. • highly resistant to abrasion • integrated temperature reading • flow detection function • measurement accuracy 0.1 % • ATEXcertified
Request for a quoteFrance
Material flow monitoring with Flow/No Flow information plus additional “Detection of blockage” or “Material flow interruption” function (Jam/NoJam) • contactless operation using microwaves • particularly reliable device due to microwaves passing through material accumulations • Measurement from outside for all nonmetallic tank walls, housings, hose lines or pipelines • usable in ATEX zones and high operating temperatures
Request for a quoteFrance
Microwave sensor for contactless monitoring of material flows with trend monitoring. • detection of material clogging and material standstill • insensitive against material deposits • for any line diameter • compact (no separate electronics) • with ceramic mounting, usable up to 1,000 °C • usable in dust exzones
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
France
FlowJam T is a sensor for monitoring the flow of solids that are conveyed through thin pipelines. The sensor can be used for tubes made of electrically nonconductive material, such as plastic or rubber, with outside diameters between 4 and 25 mm. • mounted around the tube • triboelectric measurement • free crosssection • easy retrofitting
Request for a quoteFrance
Continuous flow measurement of powder or granules in high pressure densephase conveying. Designed to measure solid flows during pneumatic dense phase transport. The sensor measures density and speed. • pressureresistant up to 64 bar • maintenancefree • contactless • ATEX category 3 approved
Request for a quoteFrance
Continuous solids mass flow measurement in densestream conveying and high levels of throughput. Designed to measure solid flows during pneumatic dense phase transport. The sensor measures density and speed. • unlimited throughput volumes can be measured • no wear thanks to the ceramic inner pipe • simple retrofitting • maintenancefree
Request for a quoteFrance
Measurement of the volume flow, especially in dusty applications. Easy installation on existing ducts, no venturi or similar conversions are required. • easy to retrofit • no calibration necessary • output in operating cubic metres • suitable for all diameters and geometries
Request for a quoteFrance
Microwave sensor for contactless monitoring of material flow in air slides. • easy to install • easy to retrofit • gives trending information by 4 20 mA output • immediate alarm when flow is interrupted
Request for a quoteFrance
Electrodynamic flow sensor for the measurement of low flow rates from 0 to 100 kg/h. For pipe diameters up to 1 m. Ideally used in leanphase conveying. In free fall conditions with at least 2 m/s drop speed. • suitable for very low concentrations • ceramic coating prevents sensor wear
Request for a quoteFrance
Electromagnetic flowmeter, designed to measure bulk material flows up to 300 t/h. The meter has no mechanical parts in the flow, is 100% dustproof and erosion free because of ceramic inner pipe. • arbitrary mounting position (inclined/free fall) • low headroom required • easy to calibrate
Request for a quoteResults for
Laminar flow equipment - Import exportNumber of results
13 ProductsCountries
Company type