Results for
NORELEM FRANCE
France
Stainless steel 1.4404. Version: Satin finished. Note: The hinges are made of weldable profile steel. The pin is fixed into the lower part of the hinge. The differing steel qualities of the weld and the beam onto which the hinge is welded must be at least equal to or better than: Stainless steel 1.4404
Request for a quoteNORELEM FRANCE
France
Stainless steel 1.4305 Lamellar insert polyamide (PA6). Seal ring CR / NBR. O-ring NBR. Version: Bright. Note: DIN EN 60423 cable glands with metric thread. Sealing and tension relief are provided by inset fins and a sealing washer. Rating IP68 (5 bar for 30 min). Cable glands are used for connecting fixed calbes and lines in housings, distributors and switch boxes. Temperature range: Static: -40 °C to +100 °C. Dynamic: -20 °C to +100 °C.
Request for a quoteNORELEM FRANCE
France
Coupling stainless steel 1.4057. Screws stainless steel 1.4301. For applications that require a small construction volume and low surface pressure. The keyless locking coupling can be fully recessed in a hub connection. for shaft diameters 6 20 mm suitable for hubs with low wall thickness minimum axial offset possible selfcentring Assembly Lightly oil keyless locking coupling on the tapered faces and contact points of the shaft and hub. Do not use MoS2 or grease. Insert keyless locking coupling in the hub seat and slide onto shaft. Tighten screws crosswise in several increments to the defined tightening torque. Dismantling Remove all screws and screw into the extraction threads of the front flange. Tighten screws crosswise in several steps until the keyless locking coupling loosens. Tolerances Shaft Recommended tolerance h8. Surface quality Rz ≤ 16 µm. Hub Recommended tolerance H8. Surface quality Rz ≤ 16 µm.
Request for a quoteNORELEM FRANCE
France
Shrink disc to connect a hollow hub to a shaft. They are mounted on the OD of the hub and generate pressure on the hub wall by reducing the ID with wedgeformed rings, creating a press fit between the hub and shaft. They are suitable for static, dynamic and shock loads. for extremely high torques no axial shaft/hub offset when assembling selfcentring The version 23380014072 has high tensile ISO 4762 screws. Assembly Remove existing transportation locks. Clean and lightly oil shaft, internal and external hub diameters. Do not use MoS2 or grease. Slide shrink disc onto hub. Then slide unit (shrink disc/hub) onto shaft and position correctly. Gently tighten clamping screws one after the other by hand. Then use a torque wrench to tighten the clamping screws crosswise in several increments to the defined tightening torque MS. 1st increment approx. 33% MS 2nd increment approx. 66% MS
Request for a quoteNORELEM FRANCE
France
Milled toothing, straight teeth engagement angle 20°, bright. Outside diameter extruded, tolerance h9. Note The gear rack teeth are cut using a hob mill. This results in minus tolerances for dimensions H and H1 up to module 2 0.2 mm. module 2.5 to 3 0.3 mm.
Request for a quoteNORELEM FRANCE
France
Milled toothing, straight teeth. Engagement angle 20°, bright. Note Up to 70 teeth with hub one side, from 80 teeth supplied as disc form. The spur gears have a centre bore or pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the spur gears are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter. Drawing reference Form A with hub Form B without hub
Request for a quoteNORELEM FRANCE
France
Sprockets with hub one side for DIN ISO 606 roller chains. The sprockets have a centre bore or are predrilled (this can vary due to production methods). For this reason, the dimension D3 max. given in the table is the maximum diameter of the bore that the sprockets are supplied with. This pilot hole/centre bore can be customised with a reamed hole, reamed hole with keyway or a tapped hole by the customer. Alternatively, bushes can be fitted by the customer to reduce the diameter.
Request for a quoteNORELEM FRANCE
France
Packaging unit 5 metres with odd number of links. Ending with an inner link at both ends. Connecting links must be ordered separately. Note Europeantype DIN ISO 606 roller chains with curved link plates (ISO No. 06 with straight links). All chains are prestretched. Not lubricated, the chains must be lubricated depending on the application. The stainless steel roller chains offer excellent corrosion protection and good chemical resistance. They can be used in applications with water and at high temperatures. B7 = maximum value for links. Pitch = PxB1
Request for a quoteNORELEM FRANCE
France
Magnetic tape, magnetised plastic sheet. Carrier band steel. Cover band stainless steel. Version Scale with incremented coding. Pole length 5 mm. Note Simple adhesive mounting; selfassembly possible. Required tape length calculated from measuring path + sensor length "L" + (2 x run or return "B"). L = see drawing of sensor used. B = 10 mm (run and return). Technical data Coefficient of expansion (11 ± 1) x 106/K (spring steel) Temperature range Ambient temperature 20–70°C Storage temperature 40–70°C Assembly Installation using the preaffixed doublesided adhesive tape must be carried out according to the enclosed user information. On request Other lengths from 0.1–100 m, in increments of 0.1 m. Note Relative humidity 100%. Dewing is permissible. Drawing reference 1) Cover band A = 0.176 mm 2) Magnetic tape M = 1.0 mm 3) Carrier band T = 0.3 mm 4) Adhesive tape K = 0.1 mm 5) Required tape length = measuring path + L + 2 x B 6) Measuring path
Request for a quoteNORELEM FRANCE
France
Steel 1.1213. Stainless steel 1.4034. Stainless steel 1.4112. Version Steel, ground. Steel, ground and hardchromed, chrome coating 5 10 µm. Stainless steel, ground. The precision steel shafts are generally inductively surface hardened. Note The surface value obtained during the inductive hardening process guarantees high surface wear resistance. Suitable for shaft supports 21565. On request Lengths up to a max. 4000 mm. Accessory Shaft supports 21565. Drawing reference 1) chamfered
Request for a quoteNORELEM FRANCE
France
Slides stainless steel 1.4301. Ball cage stainless steel 1.4301. Balls stainless steel 1.4034. Version Slides bright. Ball cages bright. Balls bright. Note for ordering Sold in pairs. Note On telescopic slides with overextension, the travel is greater than the installed length. Latches in open position. When the release lever is actuated, the drawer can be taken out easily and separated from the guide. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 400 mm and is based on the maximum value with 10,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide.
Request for a quoteNORELEM FRANCE
France
Bearing block and carriage aluminium alloy. Guide column and threaded spindle stainless steel. Plain bearing for guide columns and spindle nut highquality special plastic. Claw coupling aluminium with polyurethane coupling spider. Version Aluminium alloy anodised. Stainless steel hardened and ground. Threaded spindle with ball bearing. Note for ordering The unit is supplied with the position of cable outlet or control unit as shown in the drawing. Note Positioning stages for motorised adjustment and positioning tasks. The plain bearings and spindle nuts are suitable for dry running, however lubrication with a grease for plastic plain bearings is recommended. The suitable programming software and interface cable for the stepper motor with positioning control are available as accessories (2500015).
Request for a quoteNORELEM FRANCE
France
Outer jacket stainless steel. Cage stainless steel. Balls stainless steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seals and a stainless steel cage. The bearing is secured with DIN 471/472 circlips. Linear ball bearings with doublesided seals should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts.
Request for a quoteNORELEM FRANCE
France
Steel 1.0718 or stainless steel 1.4305. Version: Steel electro zinc-plated. Stainless steel bright.
Request for a quoteNORELEM FRANCE
France
Plate die-cast zinc or stainless steel 1.4305. Anti-slip plate thermoplastic elastomer. Version: Die-cast zinc plate, black powder-coated. Stainless steel plate, bright. Note: Swivel feet consist of a plate and a threaded spindle or ball joint. Any plate can be combined with any threaded spindle or ball joint. The anti-slip plate absorbs vibrations and prevents the swivel foot slipping. For matching threaded spindles see 27810. For matching ball joints see 27811.
Request for a quoteNORELEM FRANCE
France
Bearing block and carriage aluminium alloy, anodised. Guide columns stainless steel, ground. Spindle stainless steel, rolled thread. Guide bearing maintenancefree. Version Radial play on guide < 0.02 mm. No axial backlash. Spindle selflocking, with additional lock. Note The almost playfree guides and absolutely playfree spindle allow for adjustment without the need to loosen or clamp the spindle. The scale graduation is in 5 or 10 increments; 1 increment corresponds to 0.1 mm of travel. The cross stage can be easily combined with positioning stages, vertical stages and other accessories of respective size by the modular principle.
Request for a quoteNORELEM FRANCE
France
Bullseye level body stainless steel up to Ø14 mm, then aluminium. Sight window glass. Version Aluminium black anodised. Note Bubble levels are used as a type of zero indicator instrument for checking horizontal inclination in e.g. spirit levels, inclinometers, metrology instruments and machine constructions. Excellent bubble contour, with internal bubble ring to eliminate planar parallaxes. Sensitivity in angular minutes for 2 mm bubble travel Clear filling
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
Steel 1.7225. Stainless steel 1.4305. Version: Seel version trivalent blue passivated. Stainless steel version bright. Note: Levelling sets are used for mounting, levelling and aligning motors, aggregates, drive units and assembly lines. They have a large adjustment range of 15 mm to 40 mm. Other sizes available on request.
Request for a quoteNORELEM FRANCE
France
Seel version trivalent blue passivated. Stainless steel version bright. Note: The spherical washer levelling set is used to mount and align motors, aggregates, drive units and production lines. The spherical washer gives exact alignment of sloping faces with an inclination of up to 4°. The locknut secures a prescribed adjustment. Accessory: Spherical levelling washers 07460
Request for a quoteNORELEM FRANCE
France
Steel. Stainless steel 1.4305. Stainless steel A4 1.4401. Version: Steel electro zinc-plated. Stainless steel bright. Note: Block hinges with fastening nuts and extended middle section for inset doors. Mounted with nuts (M6 or M8) from inside. The hinge can be mounted left or right. The opening angle is 180°. Supplied unassembled. Fastening nuts and washers are supplied.
Request for a quoteNORELEM FRANCE
France
Investment cast 1.4308 stainless steel. ISO 4762 cap screw and ISO 4032 hex nut, stainless steel. From ø30 mm ISO 4017 hex head bolt, stainless steel. Version: Electropolished. Note: The tube clamps with diameters 30 and 40 mm have a silicone sleeve that protects the thread of the hex head screw from contamination and damage. On request: Clamping levers for tightening. Accessory: - Round and square tubes 29050
Request for a quoteARSILAC
France
TECHNICAL SPECIFICATIONS - Reference : 006945 - 304L stainless steel tank - Storage tank - Vertical cylindrical on legs - Off-centre conical dome - Conical bottom with 38% slope - Interior and exterior finish: glazed 2B - Off-centre chimney diam. 400 mm and height 300 mm - ELICA 316L stainless steel anti-retention top flap - Oval ELICA autoclave door 308x440 mm, inside opening at bottom of shell - 3 single male DIN 80 connections on the dome - Double-acting ELICA 1000 HL stainless steel 316L horn-mounted valve - 5 lifting rings, 1 of which is at the foot of the tank - Support + manufacturer's plate - 1 single male DIN 65 ferrule connection - 1 single male DIN 65 ferrule connection - Weight : 928 Kg DIMENSIONS - Diameter: 2470 mm - Height : 5525 mm
Request for a quoteARSILAC
France
TECHNICAL CHARACTERISTICS - Model : STOIP SER 2500 SPEC - Effective capacity : 2547 litres - Brushed exterior finish - Mirror-polished interior finish - Top door Ø 400 mm - Cooling coil: 4 turns H. 560 mm + 2 turns around the door H.300 mm - Socket for probe - 3 adjustable stainless steel feet H: 500 mm - Rectangular door: 420 x 530 mm - Positioned flush with the bottom of the shell - Stainless steel taster tap DIN15 - Level tap Ø 20 with stainless steel protection - Stainless steel ladder support bar - Vacuum lifting rings - Thermometer with clock - Clearance and total emptying with stainless steel ball valves on 100x100 square flange - Outlet 40 MACON DIMENSIONS - Diameter: 1400 mm - Height : 2445 mm
Request for a quoteARSILAC
France
TECHNICAL SPECIFICATIONS - Belon stainless steel - Butterfly drain valve - Level tube with millimetre scale - Central reinforcement DIMENSIONS - Total length: 4500 mm - Width: 1400 mm - Height: 1400 mm
Request for a quoteARSILAC
France
TECHNICAL SPECIFICATIONS - Vertical cylindrical on legs - Off-centre conical dome - 38% sloping conical base - Interior and exterior finish: glazed 2B - Off-centre chimney diam. 400 mm and height 300 mm - ELICA 316L stainless steel anti-retention top flap - Oval ELICA autoclave door 308x440 mm, inside opening at bottom of shell - 3 single male DIN 80 connections on the dome - Oval autoclave door ELICA 308x440 mm internal opening at bottom of shell - Double-acting ELICA 1000 HL stainless steel 316L horn-mounted valve - 5 lifting rings, including 1 at bottom of tank - Bracket + manufacturer's plate - 1 single male DIN 65 connection in shell - 1 single male DIN 65 ferrule connection - Earth connection - Total drain pipe + male at end of pipe DIN 65 DIMENSIONS AND WEIGHT - Diameter: 2420 mm - Height : 4517 mm - Weight : 754 Kg
Request for a quoteARSILAC
France
TECHNICAL SPECIFICATIONS - Vertical cylindrical on legs - Off-centre conical dome - Conical base with 38% slope - Interior and exterior finish: glazed 2B - Off-centre chimney Ø 400 mm and height 300 mm - ELICA 316L stainless steel anti-retention top flap - Oval ELICA autoclave door 308 x 440 mm with internal opening at bottom of shell - 3 single male DIN 80 connections on the dome - Double-acting ELICA 1000 HL stainless steel 316L horn-mounted valve - 3 lifting rings, 1 of which is at the foot of the tank - Bracket + manufacturer's plate - 1 single male DIN 65 ferrule connection - 1 single male DIN 65 ferrule connection - Earth connection - Total drain pipe + male DIN 65 end fitting - 4 external feet, height 800 mm DIMENSIONS and WEIGHT - Diameter: 2000 mm - Height : 4450 mm - Weight : 585 Kg
Request for a quoteARSILAC
France
TECHNICAL FEATURES - Year : 1990 - Internal propeller for punching down and devatting, driven by gear motor - 2 external heat exchangers of about 2 m2 - Drainage grid at the front of the tank DIMENSIONS - Length : 3350 mm - Width : 2000 mm
Request for a quoteARSILAC
France
304 stainless steel tank Model SPABP600 With pneumatic system On feet Curved bottom tank Atmospheric pressure Corked exterior finish Mirrorpolished interior finish 2 valves at outlet 40 MACON 1 stainless steel 316L floating cap and complete pneumatic system (stainless steel cover, pump, air chamber, valve)
Request for a quoteResults for
Stainless steels - Import exportNumber of results
92 ProductsCountries
Company type