Plain - Import export

Wide Flat Washers (Flat) Inox A2 - DIN 9021 There is a variant in Inox A4

Cut Flat Washers (125 refractory) AISI 310 - DIN 125 A

Cut-Out Flat Washers (Plate Dép) Inox A4 - DIN 125 A There is a variant in Inox A2

Cut-Out Flat Washers (Plate Dép) Inox A2 - DIN 125 A There is a variant in Inox A4

Rondelles Plates Larges (Plate) Inox A4 - DIN 9021 Existe une variante en Inox A2

Large Flat Washers Type L Brass - NFE 25513

Extra Large Flat Washers Type LL (Flat "LL") Inox A4 - NFE 25513 There is a variant in Inox A2

Extra Large Flat Washers Type LL (Flat "LL") Inox A2 - NFE 25513 There is a variant in Inox A4

Wide Flat Washers Type L (Flat "L") Inox A4 There is a variant in Inox A2

Narrow Flat Washers Type L (Flat "L") Inox A4 - NFE 25514 There is a variant in Inox A2

Highperformance polymer iglidur® G, iglidur® J or iglidur® X. Version iglidur® G grey; iglidur® J yellow; iglidur® X black Note Plastic highperformance polymer plain bearings. – maintenancefree – lubricantfree – corrosionresistant – resistant to dirt – high dimensional precision – high pressure resistance – good heat dissipation – very low creep tendencies – high mechanical damping – resistant to UV radiation. Assembly The bearings are designed for press fits in H7 bores. After pressing in, the ID of the bearing will be diameter D with the relative tolerance. The bearings are suitable for shafts with h tolerance (recommended min. h9).

Selflubricating. Hardness 190220 HB. Note The guide bushes are radially and axially applicable. The bearing elements are maintenancefree and wearresistant. The graphite inserts provide lifelong lubrication. Preferably for travel speeds < 0.5 m/s. (Additional lubrication is recommended for extreme loading with a higher travel speeds). Temperature range Temporary temperature peaks up to ca. 200°C. Tolerances The bore for the bearings should correspond to ISO tolerance H7. The tolerance h6 to h7 is recommended for the shaft.

Exceptionally wearresistant Dimensionally stable even at high temperatures Electrically insulating Frequency neutral

Housing igumid® G. Swivel ball iglidur® W300 Note The ability to pivot allows pillow block bearings to compensate for misalignment and possible shaft deflection. They are easy to install and suitable for the accomodation of rotating, oscillating and linear movements. igubal® pillow block bearings are maintenance free and conceived for dry running condition. Assembly These pillow block bearings are designed for mounting with 2 screws. The ID tolerance is E10. The matching shaft should have a tolerance of h6 to h9.

Universal joints with plain bearing can be swivelled by 45°. Max. transferable torque (Nm) at 150 rpm, operation angle α < 5°. * Bore depth is less than by DIN 808.

Housing anodised aluminium. Bearing surface Frelon (Teflon plus proprietary fillers). Virtually chemically inert. Selflubricating (no additional lubrication required). High temperature range (240 °C to +260 °C). Dampens vibrations. High static load capacity projected surface area x P (P = 1034 N/cm²) Suitable for food, pharmaceutical, medical and chemical applications. Insensitive to dirt.

Bearing block and carriage aluminium alloy. Guide column and threaded spindle stainless steel. Plain bearing for guide columns and spindle nut highquality special plastic. Claw coupling aluminium with polyurethane coupling spider. Version Aluminium alloy anodised. Stainless steel hardened and ground. Threaded spindle with ball bearing. Note for ordering The unit is supplied with the position of cable outlet or control unit as shown in the drawing. Note Positioning stages for motorised adjustment and positioning tasks. The plain bearings and spindle nuts are suitable for dry running, however lubrication with a grease for plastic plain bearings is recommended. The suitable programming software and interface cable for the stepper motor with positioning control are available as accessories (2500015).