Screws nut - Import export

When screwing the nuts onto the thread, the thread lock is plastically and elastically deformed. The elastic deformation causes a radial frictional lock against the nuts being loosened. The plastic thread lock is only effective when the nuts are fully screwed onto the male thread. The screw length must be selected so that at least two full threads protrude from the nut. Due to the plastic deformation of the thread lock, these nuts should only be used once.

The functioning principle make the wedge clamps ideal for series clamping. The wedge form can exert high clamping forces. These wedge clamps can be mounted in grid holes or T-slots. Tightening the socket screw moves the wedge down and the jaws out pressing the workpieces against the fixtures fixed stops. The wedge has a slightly elongated hole allowing for movement to compensate for tolerances. Spread width: M8 = ±0.5 mm M10 = ±1.0 mm M12 = ±1.0 mm M16 = ±1.5 mm Drawing reference: D) DIN 6912 cap screw 1) Jaw face smooth 2) Jaw face serrated 3) Wedge clamps 4) Workpiece 5) Fixed stop

Fasten the floating clamp to the fixture with the M12 screw. Adjust the height stop and the swivel range using the blue sleeve and lock with the 3x2.5 mm grub screws. When setting the height leave generous clearance above. For safe operation the M12 tapped hole must always be closed. For specific clamping applications the standard jaws can be altered or replaced. Form B: Fasten the floating clamp with M6 fastening holes to a fixture. Adjust the height stop and pivot range using the blue adjusting sleeve and clamp with grub screws (4x AF 2.5). When setting the height limit, allow ample play at the top. For specific clamping situations, the standard jaw plates can be modified or replaced.

The pneumatic hold-down clamp is suitable for clamping workpieces from above. This clamp is operated with standard pressure compressed air. The large swivel angle of the clamping arm makes it easy to insert and remove the workpieces without any obstructions, guaranteeing optimum accessibility to the workpiece. The block design of the housing offers universal fastening possibilities, which means that the clamp can be optimally adapted to the workpiece being clamped. Self-aligning pads with a smooth or serrated faces can be fitted in the clamping arm, enabling rough or machined workpieces to be clamped. These pneumatic clamps can be placed in multiple positions on the workpiece and operated in any particular order. They can be controlled manually or automatically. As these clamps are pneumatically actuated, they relieve the operator, particularly where frequent clamping processes are carried out.

Housing and arm carbon steel. Jaw tool steel. Version: Housing, black oxidised. Arm and jaw tempered and black oxidised.

We recommend using a lubricating paste to reduce wear to the adjustment screw. Risers are available to increase the height of the power clamp. Supplied with clamping element, support element, DIN 508 slot key and grade 12.9 bolt. Application: The height of the clamping arm can be infinitely adjusted using the adjustment screw and the workpiece can then be clamped. Advantages: Very high retaining forces of 22–49 kN. Low height. Simple element assembly. Enables very fast, simple clamping. Infinitely adjustable height and length. Use in 12-28 mm T-slots or M10, M12, M16, M20 grid systems. Thrust pad available in smooth and serrated versions.

Thermoplastic. DIN 7984 screws and DIN 985 nuts steel. Version: Black. Screws and nuts electro zinc-plated. Note: The standard size for round tubes is Ø18 mm or Ø30 mm. Use reducer sleeves 29042 if smaller tubes are to be clamped or a conversion from round to square tubes is required. On request: Plastic levers for locking. Accessory: - Reducer sleeves 29042 - Round and square tubes 29050

Tensioner Vesconite® plastic. Screw and nut steel. Version Screw ISO 4017, grade 8.8, electro zincplated. Nut ISO 4035, grade 8, electro zincplated. Note For tensioning roller chains. The chain tensioner set can be combined with all tensioning elements to form a readytoinstall chain clamp. The symmetrical design enables use on both sides. Large radii ensure very quiet running. The highquality plastic does not require any lubrication. The maximum chain speed should not exceed 1.5 m/s in continuous use.