Balls - Import export

Ceramic bearings Si3N4. Bearing cage PTFE. For most applications Si3N4 is the preferred material for ceramic bearings. Silicon nitride bearings are light, very hard and highly wear resistant. High and ultrahigh performance bearings are used in e.g. aerospace technology, metal production industries (high application temperatures), machine manufacturing, chemical industries (chemically aggresive substances), pharmaceutical and medical industries, semiconductor and biotechnology (clean room enviroments which may not be contaminated by lubricants). On request Special version with PEEK ball cage. Without ball cage.

Ball lock pins are used for easy fastening or joining of components or workpieces. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. Release the button to lock the balls and secure the connection. Form A is suitable for applications where high demands and precision are required. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application. Different materials in which the ball lock pins are used, weather conditions and wear can influence the determined values.

Shell, ballbearing steel. Cage, plastic. Balls, steel. Note With seals both ends. The linear ball bearing is secured using DIN 471 / 472 circlips. Application Suitable for applications where installation space is limited.

Workpieces are clamped and released by compressed air. The possible clamping diameter is from 16 to 20 mm. Material: Body, stainless steel. Seal, NBR. Version: Stainless steel bright. Note for ordering: Cylinder head screws M4X35 for fastening from below are included with delivery. Cylinder head screws with low head M5 for fastening from above are not included with delivery. Note: Installed dimensions for plate thickness 6 mm. The stated retaining forces are related to an operating pressure of 0.5 Mpa and a surface quality of Ra 1.6 µm. Repeat accuracy in this case is ±0.2 mm.

Housing hardened and black oxidised. Contact faces ground. Note: Locating bushes are placed in a fixture or interchangeable subplate and form the counterpart to the locating cylinder. The locating bushes are centred in a reamed hole and then fastened with 4 screws. The balls of the locating cylinder engage in the groove in the locating bush, thereby forming a fast, secure and highly accurate changeover unit, and reducing setup and changeover times. Attention: Please observe installation notes of the locating bushes.

Housing hardened and black oxidised. Contact faces ground. Note: This positioning and clamping system is especially suitable for installation in fixtures (plates, clamping tower blocks, etc.) in all mounting positions. The modular design allows the number of and distance between the locating cylinders to be ideally adjusted to suit the clamping task. Due to the small diameters, the spacing between the locating cylinders can also be reduced. The 3 clamping balls are mechanically released through control of the locating cylinder with the "opening" connection. The 3 clamping balls move inward and the fixture can be changed quickly. For clamping, the air is taken from the "opening" connection and the "clamping" connection then receives air on the locating cylinder. The 3 clamping balls are mechanically driven outward again and the new fixture is clamped. To achieve optimal retaining force, the locating cylinder remains connected to the air.

Locating cylinder tempered, black oxidised. Balls hardened, bright. Note: Locating cylinder with quick-clamp system for extra timesaving during setups. Insert the locating cylinder into the receiving hole and press the button. The three balls are pushed out and position the components. By tightening the set screw a 1/4 turn using an hexagonal key, the components are positively and securely held.

Steel. Version: Ball thrust pins trivalent passivated. Ball seat and nuts electro zinc-plated. Note: Axial joint suitable for taking up tractive forces. The ball's movement can be controlled or fully locked in position using the clamping nut.

Housing washer, shaft washer and rolling elements, bearing steel. Cage, steel. Note Axial ball bearings accept high axial loads from one direction but may not be loaded radially. The bearings are separable. This means the bearing parts can be fitted independently of each other. The main dimensions of the axial ball bearing conform to ISO 104 and DIN 711. Dimensional and running tolerances correspond to tolerance class PN acc. to DIN 620. These tolerance classes are standard and are well suited for most applications.

Steel housing. Nitrile rubber seal. Preloaded highaccuracy bearings with a 60° thrust angle. The bearings accept both radial and axial forces from both directions. Due to their preload, the angular contact ball bearings provide a high level of stiffness, excellent concentricity, precise tool positioning and repeatability. The integrated lowfriction seal effectively keeps dirt away from the bearing, thereby ensuring excellent operating safety and a long service life. The bearing friction coefficient Mrl is a reference value. The moment of inertia corresponds to that of the rotating inner ring. The limiting speeds are applicable after grease is applied. Technical data All bearings are supplied ready for mounting with lubricating grease type KE2P35 acc. to DIN 51825. Housing and shaft tolerances correspond to roundness tolerance class IT2 and perpendicularity tolerance class IT4.

Sprocket steel. Ball bearing chrome steel. Screw and nut steel. Version Sprocket teeth hardened to HRC 50, electro zincplated. Ball bearing with sealing discs 2ZC3. Screw ISO 4017, grade 8.8, electro zincplated. Nut ISO 4035, grade 8, electro zincplated. Note For tensioning roller chains. The sprocket set can be combined with all tensioning elements to form a readytoinstall chain clamp. The ball bearings are sealed both sides, permanently lubricated and maintenancefree. The sprocket can be moved on the screw and thus adapted to the chain track. With the duplex and triplex version, precision spacer sleeves ensure correct chain guidance. Rigid mounting without a tensioning element is also possible. Can also be used as an idler sprocket.

Housing steel. Cage plastic. Balls steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seal. The linear ball bearings have a plastic cage which results in quiet and outstanding running properties. With flange for direct mounting on the housing. Linear ball bearings with doublesided seal should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts. Precision guide shafts 21595. Fastening screws 07160.

Outer jacket stainless steel. Cage stainless steel. Balls stainless steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seals and a stainless steel cage. The bearing is secured with DIN 471/472 circlips. Linear ball bearings with doublesided seals should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts.

Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note By telescopic slides with full extension, the travel is roughly equal to the installed length, which ensures greater comfort and accessibility. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 80,000 cycles. Not suitable for horizontal mounting. The head height of the fastening screws should not exceed 1.8 mm otherwise there is a risk of collision with other parts of the slide. Advantages Low slide thickness Light running Precise guidance for high lateral stability

Ball end locating pins are specially designed to ease the locating process. The tendency to jam, caused by the locating hole not being at right angles to the pin or by the pushing force not being parallel to the pin axis, is minimized by the ball-end form (see illustration).

Ball lock pins are used for easy fastening or joining of components. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. When the push button is released, the balls lock the connection securely. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application. Different materials in which the ball lock pins are used, weather conditions and wear can influence the determined values.

Ball lock pins are used for easy fastening or joining of components. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. When the push button is released, the balls lock the connection securely. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application. Different materials in which the ball lock pins are used, weather conditions and wear can influence the determined values. Ball lock pins with high shear strength are identified by a groove marking on the pin.

These bushes are ideal for easy and quick positioning of ball lock pins and locking pins. Advantages: centred by the centring collar. easy and reliable installation. can be screwed into various materials. usable both sides

Ball lock pins are used for easy fastening or joining of components or workpieces. The two balls are disengaged by pressing the push button and the pin can be slipped into holes in the workpieces. Release the button to lock the balls and secure the connection. If required, the ball lock pins can be fitted with a retaining cable. The hardened, high-tensile stainless steel pin permits extreme loads with low wear. Shear force double shear (F) = S · τ aB max. The values given for the shear force are the theoretical breaking load. These are non-binding reference values without consideration of safety factors and exclude any liability. The values given are for information purposes only and do not constitute a legally binding assurance of properties. The load values have been calculated in accordance with DIN 50141. Each user must determine individually whether the ball lock pin is suitable for the respective application.

Locking pins are used for quick and easy fixating and joining of parts and workpieces. Shearing force double shear (F) = S · τ aB max. The locking pins with key ring represent a cost-effective alternative to other locking pins.

Quick catch for various applications such as holding doors, hatches, screens etc. closed. The double ball catch consists of a housing and a latch bracket that engages between the two balls. The latch bracket can engage from the front or the side. The engagement pressure is adjustable. Drawing reference: 1) counterbore DIN 74-A

Sleeve steel grade 5.8. Ball steel. Spring grade D steel wire.

Ball element case-hardened steel. Thrust pad ETG 100 steel.

Housing anodised aluminium. Bearing surface Frelon (Teflon plus proprietary fillers). Virtually chemically inert. Selflubricating (no additional lubrication required). High temperature range (240 °C to +260 °C). Dampens vibrations. High static load capacity projected surface area x P (P = 1034 N/cm²) Suitable for food, pharmaceutical, medical and chemical applications. Insensitive to dirt.

Housing steel. Cage plastic. Balls steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seal. The linear ball bearings have a plastic cage which results in quiet and outstanding running properties. With flange for direct mounting on the housing. Linear ball bearings with doublesided seal should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts. Precision guide shafts 21595. Fastening screws 07160.

Ball-end thrust screws with full ball are used when a clean, polished contact surface is required.

Ball, aluminium. Magnet, neodymium. Body, steel. Holding ring, steel lined with leather. Version Anodised. Holding ring chemically nickelplated. Note The magnetic clamping balls are used to gently hold components in the optimum working position during e.g. polishing, assembling and laser welding. Swivel angles of up to 90° can be set, depending on the workpiece geometry and weight. The magnetic ball can be turned on and off using the Tgrip hex key provided.

Inner ring, outer ring and rolling elements, bearing steel. Cage sheet steel. Labyrinth seal sheet steel. Lip seal NBR. Version 2Z = sealed both sides with noncontact labyrinth seals. 2RSR = sealed both sides with contact lip seals. Note Deep groove ball bearings accept high radial and axial loads. Axial loads are absorbed in both directions. The versions 2Z and 2RSR are lubricated for life with a high quality grease. The main dimensions of the deep groove ball bearings conform to DIN 6251. Dimensional and running tolerances correspond to tolerance class PN acc. to DIN 620. The radial internal clearance corresponds to the clearance CN acc. to DIN 6204. These tolerance classes are standard and well suited for most applications.