Results for
NORELEM FRANCE
France
Steel. Stainless steel 1.4305. Stainless steel A4 1.4401. Version: Steel electro zinc-plated. Stainless steel bright. Note: Block hinges with fastening nuts and extended middle section for inset doors. Mounted with nuts (M6 or M8) from inside. The hinge can be mounted left or right. The opening angle is 180°. Supplied unassembled. Fastening nuts and washers are supplied.
Request for a quoteNORELEM FRANCE
France
Investment cast 1.4308 stainless steel. ISO 4762 cap screw and ISO 4032 hex nut, stainless steel. From ø30 mm ISO 4017 hex head bolt, stainless steel. Version: Electropolished. Note: The tube clamps with diameters 30 and 40 mm have a silicone sleeve that protects the thread of the hex head screw from contamination and damage. On request: Clamping levers for tightening. Accessory: - Round and square tubes 29050
Request for a quoteNORELEM FRANCE
France
Stainless steel 1.4404. Version: Satin finished. Note: The hinges are made of weldable profile steel. The pin is fixed into the lower part of the hinge. The differing steel qualities of the weld and the beam onto which the hinge is welded must be at least equal to or better than: Stainless steel 1.4404
Request for a quoteNORELEM FRANCE
France
Plate die-cast zinc or stainless steel 1.4305. Anti-slip plate thermoplastic elastomer. Version: Die-cast zinc plate, black powder-coated. Stainless steel plate, bright. Note: Swivel feet consist of a plate and a threaded spindle or ball joint. Any plate can be combined with any threaded spindle or ball joint. The anti-slip plate absorbs vibrations and prevents the swivel foot slipping. For matching threaded spindles see 27810. For matching ball joints see 27811.
Request for a quoteNORELEM FRANCE
France
Steel or stainless steel 1.4404. Version: Steel electro zinc-plated. Stainless steel bright.
Request for a quoteNORELEM FRANCE
France
Steel 1.0718 or stainless steel 1.4305. Version: Steel electro zinc-plated. Stainless steel bright.
Request for a quoteNORELEM FRANCE
France
Cable fasteners: Stainless steel 1.4404 or PVDF. Hose: Plastic. Version: Cable gland: bright stainless steel, transparent plastic. Hose: coated Note: Washers supplied. EN 60423 metric thread. IP rating 66, 68 up to 15 bar, 69K. Tension relief corresponds to EU standard 62444. EHEDG certified. Seal insert ADI - free Temperature range: Stainless steel cable glands: -40 °C to +85 °C. Plastic cable glands: -20 °C to +85 °C. Hose: -20 °C to +95 °C.
Request for a quoteNORELEM FRANCE
France
Stainless steel 1.4305 Lamellar insert polyamide (PA6). Seal ring CR / NBR. O-ring NBR. Version: Bright. Note: DIN EN 60423 cable glands with metric thread. Sealing and tension relief are provided by inset fins and a sealing washer. Rating IP68 (5 bar for 30 min). Cable glands are used for connecting fixed calbes and lines in housings, distributors and switch boxes. Temperature range: Static: -40 °C to +100 °C. Dynamic: -20 °C to +100 °C.
Request for a quoteNORELEM FRANCE
France
Coupling stainless steel 1.4057. Screws stainless steel 1.4301. For applications that require a small construction volume and low surface pressure. The keyless locking coupling can be fully recessed in a hub connection. for shaft diameters 6 20 mm suitable for hubs with low wall thickness minimum axial offset possible selfcentring Assembly Lightly oil keyless locking coupling on the tapered faces and contact points of the shaft and hub. Do not use MoS2 or grease. Insert keyless locking coupling in the hub seat and slide onto shaft. Tighten screws crosswise in several increments to the defined tightening torque. Dismantling Remove all screws and screw into the extraction threads of the front flange. Tighten screws crosswise in several steps until the keyless locking coupling loosens. Tolerances Shaft Recommended tolerance h8. Surface quality Rz ≤ 16 µm. Hub Recommended tolerance H8. Surface quality Rz ≤ 16 µm.
Request for a quoteNORELEM FRANCE
France
Shrink disc to connect a hollow hub to a shaft. They are mounted on the OD of the hub and generate pressure on the hub wall by reducing the ID with wedgeformed rings, creating a press fit between the hub and shaft. They are suitable for static, dynamic and shock loads. for extremely high torques no axial shaft/hub offset when assembling selfcentring The version 23380014072 has high tensile ISO 4762 screws. Assembly Remove existing transportation locks. Clean and lightly oil shaft, internal and external hub diameters. Do not use MoS2 or grease. Slide shrink disc onto hub. Then slide unit (shrink disc/hub) onto shaft and position correctly. Gently tighten clamping screws one after the other by hand. Then use a torque wrench to tighten the clamping screws crosswise in several increments to the defined tightening torque MS. 1st increment approx. 33% MS 2nd increment approx. 66% MS
Request for a quoteNORELEM FRANCE
France
Milled toothing, straight teeth engagement angle 20°, bright. Outside diameter extruded, tolerance h9. Note The gear rack teeth are cut using a hob mill. This results in minus tolerances for dimensions H and H1 up to module 2 0.2 mm. module 2.5 to 3 0.3 mm.
Request for a quoteNORELEM FRANCE
France
Milled toothing, straight teeth. Engagement angle 20°, bright. Note Up to 70 teeth with hub one side, from 80 teeth supplied as disc form. The spur gears have a centre bore or pilot hole (this can vary due to manufacturing methods). For this reason, the dimension D2 max. given in the table is the maximum diameter of the bore with which the spur gears are supplied. This pilot/centre bore can be amended by the customer to produce a reamed bore, reamed bore with keyway or a tapped hole. Alternatively, customers can also use bushes to reduce the bore diameter. Drawing reference Form A with hub Form B without hub
Request for a quoteNORELEM FRANCE
France
Sprockets with hub one side for DIN ISO 606 roller chains. The sprockets have a centre bore or are predrilled (this can vary due to production methods). For this reason, the dimension D3 max. given in the table is the maximum diameter of the bore that the sprockets are supplied with. This pilot hole/centre bore can be customised with a reamed hole, reamed hole with keyway or a tapped hole by the customer. Alternatively, bushes can be fitted by the customer to reduce the diameter.
Request for a quoteNORELEM FRANCE
France
Packaging unit 5 metres with odd number of links. Ending with an inner link at both ends. Connecting links must be ordered separately. Note Europeantype DIN ISO 606 roller chains with curved link plates (ISO No. 06 with straight links). All chains are prestretched. Not lubricated, the chains must be lubricated depending on the application. The stainless steel roller chains offer excellent corrosion protection and good chemical resistance. They can be used in applications with water and at high temperatures. B7 = maximum value for links. Pitch = PxB1
Request for a quoteNORELEM FRANCE
France
Bullseye level body stainless steel up to Ø14 mm, then aluminium. Sight window glass. Version Aluminium black anodised. Note Bubble levels are used as a type of zero indicator instrument for checking horizontal inclination in e.g. spirit levels, inclinometers, metrology instruments and machine constructions. Excellent bubble contour, with internal bubble ring to eliminate planar parallaxes. Sensitivity in angular minutes for 2 mm bubble travel Clear filling
Request for a quoteNORELEM FRANCE
France
Magnetic tape, magnetised plastic sheet. Carrier band steel. Cover band stainless steel. Version Scale with incremented coding. Pole length 5 mm. Note Simple adhesive mounting; selfassembly possible. Required tape length calculated from measuring path + sensor length "L" + (2 x run or return "B"). L = see drawing of sensor used. B = 10 mm (run and return). Technical data Coefficient of expansion (11 ± 1) x 106/K (spring steel) Temperature range Ambient temperature 20–70°C Storage temperature 40–70°C Assembly Installation using the preaffixed doublesided adhesive tape must be carried out according to the enclosed user information. On request Other lengths from 0.1–100 m, in increments of 0.1 m. Note Relative humidity 100%. Dewing is permissible. Drawing reference 1) Cover band A = 0.176 mm 2) Magnetic tape M = 1.0 mm 3) Carrier band T = 0.3 mm 4) Adhesive tape K = 0.1 mm 5) Required tape length = measuring path + L + 2 x B 6) Measuring path
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
Slides stainless steel 1.4301. Ball cage stainless steel 1.4301. Balls stainless steel 1.4034. Version Slides bright. Ball cages bright. Balls bright. Note for ordering Sold in pairs. Note On telescopic slides with overextension, the travel is greater than the installed length. Latches in open position. When the release lever is actuated, the drawer can be taken out easily and separated from the guide. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 400 mm and is based on the maximum value with 10,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide.
Request for a quoteNORELEM FRANCE
France
Bearing block and carriage aluminium alloy. Guide column and threaded spindle stainless steel. Plain bearing for guide columns and spindle nut highquality special plastic. Claw coupling aluminium with polyurethane coupling spider. Version Aluminium alloy anodised. Stainless steel hardened and ground. Threaded spindle with ball bearing. Note for ordering The unit is supplied with the position of cable outlet or control unit as shown in the drawing. Note Positioning stages for motorised adjustment and positioning tasks. The plain bearings and spindle nuts are suitable for dry running, however lubrication with a grease for plastic plain bearings is recommended. The suitable programming software and interface cable for the stepper motor with positioning control are available as accessories (2500015).
Request for a quoteNORELEM FRANCE
France
R-clips are used for securing bolts and axles. They are easy to install and can be reused. The ends have no sharp edges. Double coil R-clips have a flatter spring characteristics and are easier to install. The double coil allows a tether cable to be attached to prevent loss. Drawing reference: Form E: with single coil. Form D: with double coil (coil direction can differ from the drawing).
Request for a quoteNORELEM FRANCE
France
The Hygienic DESIGN fastening system was specially developed for use in food processing facilities. Special attention was paid to the cleaning-optimised geometry and a surface finish of Ra ≤ 0.8 µm. The quick and easy installation due to a pre-installed sealing washer rounds off the overall package.
Request for a quoteNORELEM FRANCE
France
EN ISO 7380-1 Form A: Hexagon socket button head screws. EN ISO 7380-2 Form B:Hexagon socket button head screws with collar.
Request for a quoteNORELEM FRANCE
France
The surface of the hexagon head bolt is polished and, with regard to design optimised for the use in hygienic environments. The bolt head is convex on the top face and the collar has a conical formed top surface. Instead of troublesome embossing or indentations, the bolt head is smooth with a surface finish of Ra 0.8 µm. Dirt and residue from products or cleaners seldom adheres and easy cleaning is ensured.
Request for a quoteNORELEM FRANCE
France
Stainless steel pull handles are used mainly on equipment in the medical and food industry as well as in laboratories and neuclear technology.
Request for a quoteNORELEM FRANCE
France
Pneumatic clamps have the following advantages compared to hand clamps: The operator is relieved of frequent clamping. Several clamps can be activated at the same time and can be closed in a specific sequence. Single or multiple clamps can be activated from varying positions by machine control or hand control. Because of the toggle system: the clamp remains closed if the air supply fails. the air consumption is low due to the large end ratio. pivoting the clamping arm achieves a large opening travel. optimum force and movement ratios are achieved. VL = air consumption per complete cycle in dm³ at 6 bar. Selection criteria: To select the correct size of pneumatic clamps, the possible clamping force at 6 bar (any compressed media are permissible, maximum pressure 10 bar) is specified besides the retaining force. F3 is the possible clamping force that the clamp exerts on the end of the clamping arm, F4 the force it exerts on the fulcrum side.
Request for a quoteNORELEM FRANCE
France
The combination of excellent material properties is a special feature of silicon nitride (Si3N4). These include high resiliance and stability, excellent wear properties and good chemical resistance.
Request for a quoteNORELEM FRANCE
France
Workpieces are clamped and released by compressed air. The possible clamping diameter is from 16 to 20 mm. Material: Body, stainless steel. Seal, NBR. Version: Stainless steel bright. Note for ordering: Cylinder head screws M4X35 for fastening from below are included with delivery. Cylinder head screws with low head M5 for fastening from above are not included with delivery. Note: Installed dimensions for plate thickness 6 mm. The stated retaining forces are related to an operating pressure of 0.5 Mpa and a surface quality of Ra 1.6 µm. Repeat accuracy in this case is ±0.2 mm.
Request for a quoteNORELEM FRANCE
France
Outer jacket stainless steel. Cage stainless steel. Balls stainless steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seals and a stainless steel cage. The bearing is secured with DIN 471/472 circlips. Linear ball bearings with doublesided seals should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts.
Request for a quoteResults for
Stainless - Import exportNumber of results
36 ProductsCompany type