Results for
NORELEM FRANCE
France
Two-piece shaft collars surround the shaft with a uniformly distributed clamping force. This leads to a dimensionally precise fit and very high retaining forces without damaging the shaft. The shaft tolerance should lie within h11. Two-piece shaft collars can be quickly and easily mounted or removed without dismantling other components.
Request for a quoteNORELEM FRANCE
France
Clamping joints are used to clamp round cross sections (bars, tubes, etc.) and are infinitely adjustable. The simple design together with the adjustable clamping lever permits rapid clamping.
Request for a quoteNORELEM FRANCE
France
Clamping levers with safety function prevent changes in the locking point through accidental opening or closing. In the default position, the lever can be freely rotated and has no connection to the clamping point. The grip lever only engages when pushed down and the clamp can the loosened or tightened. A spring sets the lever automatically into the default position when released.
Request for a quoteNORELEM FRANCE
France
By using clamping levers with integrated clamping force intensifier, the clamping force can be increased by up to 75% compared to standard clamping levers. Furthermore, this product can also be used by persons with limited hand strength (e.g. in rehabilitation) to achieve comparable clamping forces with less effort. Less effort is also needed to loosen the clamping lever. The increase in clamping force is achieved by the integral needle roller thrust bearing, which generates very low surface friction on a rigid contact surface during clamping. The hardened thrust washers are designed for high clamping forces and the bearing with its high load rating guarantees a long service life. The clamped component is permanently protected by the large, stationary contact surface. A washer is no longer required. Due to the modular construction many special designs are available.
Request for a quoteNORELEM FRANCE
France
Enter the desired lever colour here. The standard colours are: Black grey clamping lever, traffic red push button. Orange clamping lever, black grey push button. Traffic red clamping lever, black grey push button. Where L ≥ 60 mm the thread length is 60 mm. On request: Other threads, screw lengths and special versions. Dimension “H1” available in other lengths at extra charge. Drawing reference: 1) flat point DIN 78
Request for a quoteNORELEM FRANCE
France
Other threads, screw lengths and special versions. Dimensions “H1” and “A” available in other lengths at extra charge.
Request for a quoteNORELEM FRANCE
France
Latches with draw bail for securing and locking hatches, container lids, machine cladding etc. By exceeding the dead centre they resist vibration. The locking force is applied by drawing on the bail. The latches can be screwed down or riveted. We recommend using countersunk screws for fastening the components. Order catch plates separately.
Request for a quoteNORELEM FRANCE
France
Steel parts electro zinc-plated. Hinge pins tempered. Plastic handle oil-resistant. Note: See 05200 – 05280 for accessories.
Request for a quoteNORELEM FRANCE
France
The functioning principle make the wedge clamps ideal for series clamping. The wedge form can exert high clamping forces. These wedge clamps can be mounted in grid holes or T-slots. Tightening the socket screw moves the wedge down and the jaws out pressing the workpieces against the fixtures fixed stops. The wedge has a slightly elongated hole allowing for movement to compensate for tolerances. Spread width: M8 = ±0.5 mm M10 = ±1.0 mm M12 = ±1.0 mm M16 = ±1.5 mm Drawing reference: D) DIN 6912 cap screw 1) Jaw face smooth 2) Jaw face serrated 3) Wedge clamps 4) Workpiece 5) Fixed stop
Request for a quoteNORELEM FRANCE
France
Cam tool steel, hardened and black oxidised. Shaft carbon steel, hardened and black oxidised. Grip carbon steel, black oxidised. Ball knob black thermoset PF 31. Note: Admissible hand force for the handle. Accessory: Standard handles 06355. Screw-in handles with adjustable torque 06357.
Request for a quoteNORELEM FRANCE
France
The pneumatic hold-down clamp is suitable for clamping workpieces from above. This clamp is operated with standard pressure compressed air. The large swivel angle of the clamping arm makes it easy to insert and remove the workpieces without any obstructions, guaranteeing optimum accessibility to the workpiece. The block design of the housing offers universal fastening possibilities, which means that the clamp can be optimally adapted to the workpiece being clamped. Self-aligning pads with a smooth or serrated faces can be fitted in the clamping arm, enabling rough or machined workpieces to be clamped. These pneumatic clamps can be placed in multiple positions on the workpiece and operated in any particular order. They can be controlled manually or automatically. As these clamps are pneumatically actuated, they relieve the operator, particularly where frequent clamping processes are carried out.
Request for a quoteNORELEM FRANCE
France
Housing and arm carbon steel. Jaw tool steel. Version: Housing, black oxidised. Arm and jaw tempered and black oxidised.
Request for a quoteNORELEM FRANCE
France
1. Screw the locking screw into the collar bush, fixture clamp and clamping unit and screw onto the baseplate. 2. The workpiece is clamped by tightening the fixture clamp with a spanner. Advantages: Compact design Quick and easy clamping of components Pull-down effect Drawing reference: 1) Locking screw 2) Collar bush 3) Fixture clamp 4) Clamping unit
Request for a quoteNORELEM FRANCE
France
Body carbon steel, black oxidised. Jaw carbon steel, tempered, black oxidised. Note: The adjustable toe clamp is used together with the rack plate CL.
Request for a quoteNORELEM FRANCE
France
These toe clamps can be used on machine tables or adapter plates. The positive down force holds the workpiece down on the supporting surface. The square washer can adapt slightly to an angular position i.e. the workpiece does not have to be exactly parallel. The clamping washer has a smooth side for machined surfaces and a serrated side for rough faces.
Request for a quoteNORELEM FRANCE
France
1. Screw the locking screw into the collar bush and fixture clamp and screw onto the baseplate. 2. The workpiece is clamped by tightening the fixture clamp with a spanner. Advantages: Compact design Quick and easy clamping of components Drawing reference: 1) Locking screw 2) Collar bush 3) Fixture clamp
Request for a quoteNORELEM FRANCE
France
Hook clamps and clamping screw carbon steel, tempered.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
The pneumatic swing clamp is suitable for clamping workpieces from above. The swivel and clamping function occurs pneumatically. The swivel function enables unobstructed insertion and removal of the workpiece. Optimum accessibility to the workpiece is guaranteed. The foot of the housing offers universal fastening possibilities, enabling the swing clamp to be optimally aligned with the workpiece being clamped. The swing clamps are available in left or right swivelling versions. Pneumatic swing clamps can also be placed in multiple positions on the workpiece and operated in a particular order. They can be controlled manually or automatically.
Request for a quoteNORELEM FRANCE
France
Swing clamps are used where the clamping points must be free when the workpiece is loaded or removed.
Request for a quoteNORELEM FRANCE
France
Grip black or traffic red RAL3020. Thrust washer black. Hinge pin bright. Stud and washer trivalent blue passivated or bright stainless steel. Note: Adjustable cam levers are used if the position of the lever relative to the axis of tension only permits one specific position (interference circle). The exact position of the lever is adjusted using a screwdriver on the fine thread setscrew. Plastics are subject to creeping under load (retardation), this can cause reduced clamping force. Drawing reference: 1) setscrew for fine adjustment of lever
Request for a quoteNORELEM FRANCE
France
Handle electropolished or blasted. Thrust washer, hinge pin and screw bright. Note: The thrust washer face is lightly greased before delivery. The grease is FDA conform and is suitable for use in the foodstuff and pharmaceutical industries.
Request for a quoteNORELEM FRANCE
France
Handles cast aluminum EN AC-46200. Thrust washer plastic PA 66 GF 35-X fibreglass reinforced. Hinge pin stainless steel 1.4305. Studs and washer steel grade 5.8 or stainless steel 1.4305. Version: Handles fine structured powder-coated, black or red RAL 3003. Thrust washer black. Hinge pin bright. Studs and washer blue passivated steel or bright stainless steel. Note: Plastics are subject to creeping under load (retardation).
Request for a quoteNORELEM FRANCE
France
Form A: Tempered and electro zinc-plated. Form B: Tempered and electro zinc-plated. Complete with DIN 787 screw for T-slots, DIN 6340 washer and DIN 6330B nut. Form C: Tempered and electro zinc-plated. Complete with DIN 6379 stud, DIN 6340 washer and DIN 6330B nut. Note: These clamp strap assemblies can be quickly and infinitely adapted to the clamping situation. The clamp straps have different heel types both sides enabling the best end to be selected depending on the specific application. These extremely versatile clamp straps are suitable for use by metal cutting or non-cutting machining and also for press and injection-moulding applications.
Request for a quoteNORELEM FRANCE
France
The collet is opened by applying compressed air to the "open" port. The collet is closed (for clamping) by applying compressed air to the "close" port. The pneumatic connections can be screwed on either from below or from the side. If the air is connected from below, the side ports must be closed. Machining the collet for external clamping: The negative form of the workpiece to be clamped is machined into the collet. Free-form and asymmetrical contours are possible. Different workpieces can be clamped quickly and securely by simply exchanging the collet. The collet can be milled down to height H2. This enables multiple workpiece contours to be machined into one collet. Repeat accuracy for workpiece: +/-0.03 Repeat accuracy after replacing the collet +/- 0.02 The collet radial clamping travel is 0.15 mm per clamping segment. To prevent damage the collet should not be tightened without a workpiece or clamping ring in place. The operating air pressure should lay between 0.45 - 0.55 MPa.
Request for a quoteNORELEM FRANCE
France
Collets for clamping external contours. The contour of the workpiece to be held is inserted into the collet. Free-form and asymmetrical contours can be held. The collet mechanism enables a secure clamping of the workpiece. Clamping travel per collet segment (8x) max. 0.15 mm. Workpiece repeat accuracy: ±0.03. Collet repeat accuracy: ±0.02. Matching adaptor 03167.
Request for a quoteNORELEM FRANCE
France
These centring clamps enable workpieces to be centred on and lightly clamped in a bore. The clamps have a wide expansion range. The series covers a bore range of Ø12 to Ø30 mm. To increase the centring accuracy the clamps with internal thread have a centring spigot (D2) for a locating hole. The centring accuracy is ±0.2 mm. Centring clamps with female threads fit on M6 grid systems (see illustration).
Request for a quoteNORELEM FRANCE
France
The lateral clamping screw tightens the jaws and clamps the workpiece on the circumference. The simple and compact design allows 2 workpieces to be clamped. The clamping travel is max. 0.5 mm. The jaws must be pre-tensioned before machining the contour, the supplied clamping ring is used for this purpose.
Request for a quoteNORELEM FRANCE
France
It is recommended that the cam lever is in a vertical position when the collet is positioned in the bore. The function of the clamping system was tested in bores with tolerance H7. All values for retaining force are guide values and are given without safety factor. The suitability for the respective application must be checked by the user. Advantages: Two components can be joined together without tools. The components are perfectly centred in the clamped state. The compact design means that the mandrel collet with cam lever can even be used in blind holes. There are no specific dimensional requirements for the holes. Additionally, the surfaces and design do not need to have any specific properties. Functional principle: The clamping system is inserted in the hole in the open state. At the beginning of the locking process, the mandrel collet expands and clamps itself in the lower component. The integrated disc spring assembly creates a positive down force
Request for a quoteNORELEM FRANCE
France
Body and jaw holder hardened and ground. Note for ordering: Supplied with hexagon crank handle. Order jaw plates separately. Note: Mechanically operated centric vice. Suitable for automation: prepared with gripper slot for handling systems. Flexible mounting: suitable for zero-point systems, mounting on machine tables or on custom systems via a baseplate. Centring precision: +/- 0.02 mm. The use of a torque wrench is recommended to achieve a controlled clamping force. Features: Clamping slide and spindle nut in one piece Slots and fastening threads for mounting attachment jaws Reversible jaws (accessories) with lateral thread for workpiece stop enables a wider clamping range Good swarf and coolant removal
Request for a quoteResults for
Collars - Import exportNumber of results
66 ProductsCompany type
Category