Results for
NORELEM FRANCE
France
By using clamping levers with integrated clamping force intensifier, the clamping force can be increased by up to 75% compared to standard clamping levers. Furthermore, this product can also be used by persons with limited hand strength (e.g. in rehabilitation) to achieve comparable clamping forces with less effort. Less effort is also needed to loosen the clamping lever. The increase in clamping force is achieved by the integral needle roller thrust bearing, which generates very low surface friction on a rigid contact surface during clamping. The hardened thrust washers are designed for high clamping forces and the bearing with its high load rating guarantees a long service life. The clamped component is permanently protected by the large, stationary contact surface. A washer is no longer required. Due to the modular construction many special designs are available.
Request for a quoteNORELEM FRANCE
France
Housing steel. Clamping lever plastic. Threaded spindle grade 12.9. Version Housing nickelplated. Clamping lever, spindle black oxidised. Note Manually operated clamping elements for static clamping tasks. Manual clamping process using the freely adjustable clamping lever. The floating clamp ensure symmetrical application of force onto the rail. Up to 50,000 static clamping cycles (B10d value). In general, a friction connection is created between the clamping element and the the linear guide on the open faces of the profile guide rail so that the ball guide tracks are not damaged. The retaining force is tested on an oil smeared profile guide rail. An adapter plate, dependent on the type of carriage used, is required for height adjustment.
Request for a quoteNORELEM FRANCE
France
The easy operability and rapid adjustment using a scale means that the clamping jaws can be quickly and surely adapted to new workpieces The workpiece is always centred through the systematic construction of the 5-axis compact clamping system. The optimal accessibility to the workpiece allows short, standard tooling to be used. Tooling costs are significantly reduced. Positive down force by a clamping depth of >5 mm. Clamping widths of 20 mm to 320 mm are possible. Assembly: The 5-axis clamping system compact can be mounted on T-slot tables, grid systems or, using an adapter flange on conventional zero-point clamping systems. Accessory: Seating ledge 41345 Jaw plates 41320 Pendulum jaws 41325 Centre jaws 41335 Coupling for cross-clamping 41365 Order the seating ledges and jaw plates with pins separately.
Request for a quoteNORELEM FRANCE
France
The UNI lock mounting clamps can be installed in any position on machine tables, fixtures or workholding equipment (tooling plates, cubes, tombstones etc). The modular design enables the number of clamps and distance between them to be ideally adjusted to suit the clamping task. The clamps can be supplied with or without rotation lock. The high clamping forces are generated by the integrated spring package (the unit clamps when depressurised). Compressed air is applied to release the clamp. The following holding forces are possible with the UNI lock clamping bolt in conjunction with M10, M12 or M16 fastening screws: Holding force (M10) 35,000N Holding force (M12) 50,000N Holding force (M16) 75,000N Supplied with: 1x clamping module incl. 6 fastening screws. 6x screw protection caps. 2x air connection O-rings. 1x installation O-ring.
Request for a quoteNORELEM FRANCE
France
Completely mounted multi-clamping stations with integrated UNI lock Ø138 mm mounting clamps. The clamping stations are secured to the machine table directly or with clamps. Common bore patterns are pre-centred on the rear side for mounting. Clamping stations can be aligned via the 14H7 reference holes. The clamping stations are actuated via a central pneumatic connection. The high clamping forces are generated by the integrated spring package (the unit clamps in the de-pressurized state). The release process occurs pneumatically. The following retaining forces are possible with the UNI lock clamping bolt in conjunction with mounting screws M10, M12, M16: Retaining force (M10) 35,000N/module Retaining force (M12) 50,000N/module Retaining force (M16) 75,000N/module
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
Handle powder-coated, fine-textured structure. Steel parts black oxidised. Note: Standard colours are: black or ruby red RAL 3003.
Request for a quoteNORELEM FRANCE
France
Housing and arm carbon steel. Jaw tool steel. Version: Housing, black oxidised. Arm and jaw tempered and black oxidised.
Request for a quoteResults for
Clamps and fasteners- plastic - Import exportNumber of results
8 ProductsCompany type
Category