At motors - Import export

2-phase high-torque stepper motor in NEMA 17, NEMA 23 and NEMA 34 sizes with flat-milled shaft (D-shaft). 1.8ׄ° increment angle (full increment) with integrated positioning control. Note: Stepper motor with integrated positioning control. It forms a convenient unit consisting of stepper motor and intelligent controller. Reference travel is possible on a block with reduced electric current without proximity switch. Integrated rotational monitoring. Smooth running through dynamic switching of increment trip. Actuation via single I/O interface, 31 position configurations and call-ups. Control unit can be parametrised quickly and conveniently with the software. The software and manual for programming the positioning control are available as free download. When selecting a suitable motor, using just the retaining torque is not enough, as the motor’s torque decreases with the speed. It is therefore essential to select the correct motor according to the torque curve.

Seel version trivalent blue passivated. Stainless steel version bright. Note: The spherical washer levelling set is used to mount and align motors, aggregates, drive units and production lines. The spherical washer gives exact alignment of sloping faces with an inclination of up to 4°. The locknut secures a prescribed adjustment. Accessory: Spherical levelling washers 07460

Planetary gearing for stepper motors of the NEMA 23 and NEMA 34 size. Suitable for all mounting positions. Maintenancefree thanks to lifetime lubrication. The planetary gearing is selfcentring, equipped with a flange adapter system and axial length compensation.

Bearing block and carriage aluminium alloy. Guide column and threaded spindle stainless steel. Plain bearing for guide columns and spindle nut highquality special plastic. Claw coupling aluminium with polyurethane coupling spider. Version Aluminium alloy anodised. Stainless steel hardened and ground. Threaded spindle with ball bearing. Note for ordering The unit is supplied with the position of cable outlet or control unit as shown in the drawing. Note Positioning stages for motorised adjustment and positioning tasks. The plain bearings and spindle nuts are suitable for dry running, however lubrication with a grease for plastic plain bearings is recommended. The suitable programming software and interface cable for the stepper motor with positioning control are available as accessories (2500015).

Motorization by integrated pneumatic cylinder Driving by rack and pinion system Adjustable mechanical stops Hydraulic shock absorbers Inductive sensors The wrist of a manipulator arm These rotary modules are, for example, the wrist of a manipulator arm, the turner of parts on a conveyor or the axis of rotation of an oscillating manipulator. In general, they rotate the gripper that grips the part. These modules are equipped with hydraulic dampers and inductive sensors, the rotation guidance is ensured by 2 ball bearings that allow this module to be used in all directions, even with offcentered payload. Rotary cylinder without angular play at end of stroke The end stops located under the plate allow there to be no shock in the rack and pinion transmission and no angular play at the end of the stroke. The absence of angular play allows use in assembly or precise positioning applications with 2 positions and the absence of impact in rack

Positioning table for electric motor Guided by 2 rods on ball bushings (bronze bearings on request) Motor adaptation for linear table These leadscrew tables are delivered without motor, but the adaptation of your motor can be done by us. Some adaptations are standard, especially for standard motors (NEMA17 or NEMA23), if the dimensions of your motor are not listed, contact us to check the feasibility of your motor adaptation from our rough parts. Trapezoidal screw tables for motor The trapezoidal screw is irreversible and the axial precision of these tables is <0.15 mm (in practice 0.02 to 0.10 mm). The maxi stroke is 750 mm, and any intermediate stroke can be produced. For a XY cross table, the tables are mounted on each other directly by the body with option 308922* (smooth holes are made in the body of a table). For more precise positioning applications, these tables are available with ballscrew.

Mono Hydraulic cylinder Cutting stroke 110 mm 4 manual or motorized mechanical stops accuracy +/ 0.01 mm Through cut and kiss cut on hardened steel plate 60 HRC Picard accuracy +/ 0.01 mm Slow down stroke 10mm before touching the material Fast die change Touchscreen control in different languages Standard electrical, hydraulic and pneumatic parts Safety guards and/or photocells Class 4 Meets CE

Advantages IP55 fully sealed splash-and dust in an industrial environment. More compact: gains in size and weight. Good resistance.

Advantages High-resistance: IP 55 motors with aluminum frame High efficiency: IE2 and IE3 class on direct on-line and inverters, NEMA Premium. Compact: Space-saving. General applications Available on short delivery.

PERFORMANCE/BATTERIES: Lifting motor 2.2 KW Traction motor 0.75 KW Travel speed with/without loads 4.1/5.6 km/h Lifting speed with/without loads 81/121 mm/s Descent speed with/without loads 103/105 mm/s Permissible slope with/without loads 3/7 % Battery 2x12v 80Ah Autonomy 2/3 hours.