Electrical connection technology - Import export

Specially developed flexible grids in combination with electroconductive coatings provide high tensile strength and outstanding electro conductive properties solidian eGRID is now also available with different conductive surface treatments for special applications in which electrical conductivity is important. What is the problem? While raw carbon fibers themselves have very good electrical conductivity textile reinforcements are usually impregnated with a polymer that insulates the grid. Depending on the product and the impregnation polymer the surface of the carbon fibers is more or less covered and can not be electrically connected. The new technology allows us to generate a fully conductive surface of the reinforcement and to connect all carbon filaments to one conductive unit.

With the MiJET part cleaning system it is possible to keep workplaces clean and workpieces hygienically cleaned with the simplest technology. An electrical connection is not necessary. Only a compressed air connection is required to use the device. Application The actual task of the MiJET is to filter oily air. Chips of the work pieces accumulate in the container. Operators often tend to blow off finished workpieces into the machine. This quickly results in dirty working environments and poor air in the production hall. However, we avoid this by exhausting these fumes. Oils are trapped from the exhaust air and chips and coolants accumulate in the container.

With the MiJET part cleaning system it is possible to keep workplaces clean and workpieces hygienically cleaned with the simplest technology. An electrical connection is not necessary. Only a compressed air connection is required to use the device. Application The actual task of the MiJET is to filter oily air. Chips of the work pieces accumulate in the container. Operators often tend to blow off finished workpieces into the machine. This quickly results in dirty working environments and poor air in the production hall. However, we avoid this by exhausting these fumes. Oils are trapped from the exhaust air and chips and coolants accumulate in the container.

The displacement transducers operate according to the principle of run time measurement between two points of a magnetostrictive waveguide. One point is determined by a moveable position magnet, whose distance from the null point corresponds to the section to be measured. The run time of an emitted impulse is directly proportionate to this section. Conversion to an analogue measuring signal takes place in the downstream electronics. The waveguide is housed in a pressure-resistant stainless steel tube or extruded profile. To the rear of this is a die-cast aluminium housing containing the electronics in SMD technology. Electrical connection is implemented via a circular connector. In the rod version, the position magnet is located in a ring, which is guided over the rod without contact. In the profile version, it is located either in a slider, which is linked to the moving part of the machine via a ball joint, or it moves as a liftable position magnet, without wear, over the profile.

The displacement transducers operate according to the principle of run time measurement between two points of a magnetostrictive waveguide. One point is determined by a moveable position magnet, whose distance from the null point corresponds to the section to be measured. The run time of an emitted impulse is directly proportionate to this section. Conversion to a digital measuring signal takes place in the downstream electronics. The waveguide is housed in a pressure-resistant stainless steel tube or extruded profile. To the rear of this is a die-cast aluminium housing containing the electronics in SMD technology. Electrical connection is implemented via a circular connector. In the rod version, the position magnet is located in a ring, which is guided over the rod without contact. In the profile version, it is located either in a slider, which is linked to the moving part of the machine via a ball joint, or it moves as a liftable position magnet, without wear, over the profile

The displacement transducers operate according to the principle of run time measurement between two points of a magnetostrictive waveguide. One point is determined by a moveable position magnet, whose distance from the null point corresponds to the section to be measured. The run time of an emitted impulse is directly proportionate to this section. Conversion to an analogue measuring signal takes place in the downstream electronics. The waveguide is housed in a pressure-resistant stainless steel tube or extruded profile. To the rear of this is a die-cast aluminium housing containing the electronics in SMD technology. Electrical connection is implemented via a circular connector. In the rod version, the position magnet is located in a ring, which is guided over the rod without contact. In the profile version, it is located either in a slider, which is linked to the moving part of the machine via a ball joint, or it moves as a liftable position magnet, without wear, over the profile.

The displacement transducers operate according to the principle of run time measurement between two points of a magnetostrictive waveguide. One point is determined by a moveable position magnet, whose distance from the null point corresponds to the section to be measured. The run time of an emitted impulse is directly proportionate to this section. Conversion to an analogue measuring signal takes place in the downstream electronics. The waveguide is housed in a pressure-resistant stainless steel tube or extruded profile. To the rear of this is a die-cast aluminium housing containing the electronics in SMD technology. Electrical connection is implemented via a circular connector. In the rod version, the position magnet is located in a ring, which is guided over the rod without contact. In the profile version, it is located either in a slider, which is linked to the moving part of the machine via a ball joint, or it moves as a liftable position magnet, without wear, over the profile.

The displacement transducers operate according to the principle of run time measurement between two points of a magnetostrictive waveguide. One point is determined by a moveable position magnet, whose distance from the null point corresponds to the section to be measured. The run time of an emitted impulse is directly proportionate to this section. Conversion to an analogue measuring signal takes place in the downstream electronics. The waveguide is housed in a pressure-resistant stainless steel tube or extruded profile. To the rear of this is a die-cast aluminium housing containing the electronics in SMD technology. Electrical connection is implemented via a circular connector. In the rod version, the position magnet is located in a ring, which is guided over the rod without contact. In the profile version, it is located either in a slider, which is linked to the moving part of the machine via a ball joint, or it moves as a liftable position magnet, without wear, over the profile.