Vibration sensors - Import export

Housing Form A plastic. Housing Form B die-cast zinc alloy. Active face POM. Housing Form C high-alloy stainless steel Version: Voltage: U = 10 – 30 V DC Function: Normally open Switch type: PNP Mounting type: flush Security type: IP 67 Note: Non-contact, functions wear-free with high switching frequency and accuracy. Non-sensitive to vibrations, dust and moisture. Inductive sensors record all metals without contact. Form C enables screw fastening in a T-slot. Is safe and saves space as the proximity switch lays flush in the slot. Short-circuit proof and reverse-polarity protected.

Current loop powered vibration transmitters enable cost-effective and permanent monitoring of machine vibrations. They provide a standardised 4 ... 20 mA output signal, which is proportional to the RMS or peak value of the measured vibration amplitude. The transmitters are connected to existing, free inputs of a PLC or a process control system. These then issue a warning message when a preset vibration level is exceeded or switch off the machine in an emergency. — Measuring range 0 ... 25.4 mm/s — Output range 4 ... 20 mA — Frequency range 3 ... 1,000 Hz — 2-pin connection socket on top. For an individual offer, please contact us directly.

The Model 682C05 signal transmitter is used on the one hand to supply ICP(R)/IEPE vibration sensors and essentially to provide early warning of developing faults in rolling bearings, such as damage to the inner or outer ring, play and lack of lubrication. The unit provides two output signals, the vibration level and information about high-frequency peaks or shocks. The module also has a raw signal output for connecting machine condition analysers. For an individual offer, please contact us directly.

The Model 682C03 signal converter can be used to supply constant current-fed ICP®/IEPE accelerometers and connect them to 4 ... 20 mA signal circuits. The signal converter supplies an output current proportional to the RMS or peak value of the vibration acceleration, the vibration velocity or the vibration displacement (adjustable). For an individual offer, please contact us directly.

Acceleration sensors with ICP®/IEPE technology are usually used for vibration monitoring. Sensors for series use are particularly suitable if a large number of measuring points are to be monitored. The low-cost sensor models, where the sensor model 627A01 belongs, can be integrated permanently into monitoring systems or used in conjunction with a portable data collector/analyzer for route-based monitoring. The accelerometer presented here, model 602D01, can be used in ambient temperatures up to 121 °C. If the operating conditions require it, this model is also available with EX approval or with SIL-2 declaration. All sensors are supplied with a 1-point calibration according to ISO 17025. — With through hole — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.5 ... 8,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on the side Please contact us directly for an individual offer.

Usually, acceleration sensors with ICP®/IEPE technology are used for vibration monitoring. Sensors for series use are particularly suitable if a large number of measuring points are to be monitored. The low-cost sensor models, where the sensor model 627A01 belongs, can be integrated permanently into monitoring systems or used in conjunction with a portable data collector/analyzer for route-based monitoring. The accelerometer presented here, model 627A01, can be used in ambient temperatures up to 121 °C. If the operating conditions require it, this model is also available with EX approval or with SIL-2 declaration. All sensors are supplied with 1-point calibration according to ISO 17025. The industrial accelerometer, model 627A01, is equipped with a quartz sensing element. — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.33 ... 10,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on top For an individual offer, please contact us directly

Cost-effective industrial ICP®/ IEPE accelerometers are ideal for fixed installations and use in continuous on-line monitoring systems. This improves safety when installed in hazardous or inaccessible locations. Connection can be made via switches or junction boxes for route-based data acquisition systems. The Model 601A01 is suitable as a low-cost industrial ICP®/ IEPE accelerometer for a general purpose. It has a very good signal-to-noise ratio and a ceramic sensing element. The low-cost ICP®/ IEPE accelerometers have an economical design and are ideal for fixed mounting. Their rugged stainless steel housing with hermetic sealing and housing-isolated electronics, eliminate noise problems. — Industrial ICP® vibration sensor — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.27 ... 10,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on top For an individual offer, please contact us directly.

The low cost industrial ICP® / IEPE vibration sensor, model 601A02, is suitable for slow speed applications such as slow moving roller element bearings in a paper mill. Increasing the sensitivity of the sensor to 500 mV/g can improve the signal resolution in these applications. Despite their economical name, low-cost accelerometers are ideal for applications where the sensors are permanently mounted to collect vibration data 24/7, monthly or even quarterly. Low-cost accelerometers are all hermetically sealed in stainless steel housings and most are covered by IMI Sensors' Lifetime Warranty Plus programme. — Industrial ICP® vibration sensor — Measuring range 10 g — Sensitivity 500 mV/g — Frequency range 0.17 ... 10,000 Hz — Single point calibration at 100 Hz — 2-pin connection socket on top For an individual offer, please contact us directly.

The 603C01 ICP® is one model in a very diverse line of 603-Series accelerometers. The 603-Series includes alternative sensitivity models, hazardous area approved models, dual output models and models with an integral cable. For monitoring systems with many input channels, robustness, reliability and a favourable sensor price are of great importance. Low-cost sensors with ICP®/IEPE technology are used when a large number of measuring points are to be continuously monitored and an evaluation of the vibration spectrum is required. is required. — Industrial ICP®/IEPE vibration sensor — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.5 ... 10,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on top — With metric (M) or inch mounting bolt If you have any further questions about this sensor model, please do not hesitate to contact us. We will be pleased to help you.