Results for
NORELEM FRANCE
France
Reinforced threaded inserts allow threaded holes which have been damaged, torn out or jammed to be used again or to be repaired. This makes it possible to recover scrap and rejects of expensive products. Reinforced threaded inserts are suitable for use in various materials, including light metals and casting. Inserts with internal threads larger than M6 are supplied with four locking pins instead of two. Permissible deviations: The medium tolerance class applies to the threads listed, i.e. 6H for nut threads and 6g for bolt threads. Other dimensions ±0.25 mm. With reinforced threaded inserts we also offer a version with a stronger cross-section for use in applications with greater stress. Technical information see operating instructions for threaded inserts.
Request for a quoteNORELEM FRANCE
France
Self-tapping threaded inserts for making high-strength, wear-free, vibration resistant screw connections in materials with low shear strength such as aluminium and aluminium alloys, brass, bronze, cast iron, duro and thermoplastics. The threaded inserts are tapered at the bottom and have a cutting slot. By screwing in they cut their own threads inside a receiver hole. This guarantees a completely secure and firm anchoring in the host material. Internal thread D1 acc. to ISO 6H. The threaded inserts with cutting slot spring slightly inwards in the slot region in some materials. This results in a screw locking effect. If this is not desired, we recommend the threaded inserts with a cutting bore.
Request for a quoteHONSEL-GROUP
Germany
The HONSEL COIL "cone" can be installed in the same way as a coil with tab. No additional or special tools are required for process-reliable installation. When the HONSEL COIL "cone" is screwed onto the installation spindle, the conical portion of the wire thread insert creates a clamping effect between the installation tool and the coil. This ensures a stable installation process into the work piece. Advantages: — tab-free and therefore optimally designed for e-mobility due to no risk of tab debris. — Shallower blind hole depths can be realized — Subsequent processes are no longer necessary (breaking and removing of the installation tab) — No thread skipping during installation — Cycle time reduction of 20-30 % per installation — No special tools required for the installation process — The installation process improves due to the conical portion
Request for a quoteHONSEL-GROUP
Germany
Coil screw system 2G for automated and partially automated installation of wire thread inserts. Due to the slim construction, screw systems can be placed close to each other. This leads to more efficient use of existing production areas and thus to greater economic efficiency in production. The electric linear motor is very fast at up to 3.2 m/s and enables cycle times in production to be optimized. — Screwdriver Bosch BG2 — Floating screwdriver bearings — Integrated coil transfer with rotary gripper — Linear motor — Camera
Request for a quoteSOOCHOW ADVANCE INDUSTRIES CO., LTD.
China
threaded insert manufactured by CNC turning and milling material: stainless steel male thread: 7/16-20 UNF-2A female thread: 1/4-20 UNC-2B groove milled. width 0.060 +/- 0.015 inch, depth 0.062 +/- 0.015 inch size: diameter 0.525 +/- 0.015 inch, height 0.54 +/- 0.015 inch packing: individually packed in plastic tray, carton Soochow Advance Industries Co., Ltd., (website: www.sai-parts.com) supplies custom OEM mechanical parts, industrial fasteners, screws, bolts, nuts, industrial fittings, electronic hardware by precision CNC machining, CNC turning, CNC milling, CNC engineering.
Request for a quoteACTON S.A.
France
Wood Threaded Insert (Wood threaded insert) A1 stainless steel
Request for a quoteACTON S.A.
France
Metal Threaded Insert (Met Threaded Insert) A1 Stainless Steel
Request for a quoteNORELEM FRANCE
France
The required torque is set by a set screw and a graduated scale. The set value can be secured using the lateral clamping screw. When the set torque is reached the grip audibly and palpably releases. The loosening torque is higher than the tightening torque so that the torque handle can be released without any problems. The internal thread version has a hole in the set screw so that the torque handle can also be used on threaded rods. Set torque accuracy ± 5%. On request: Other thread lengths.
Request for a quoteOTTO EICHHOFF GMBH & CO. KG
Germany
Turned parts Long turned partes, small turned parts Turned, milled and grinded parts Thread inserts in brass, steel and stainless steel Possible materials: Alloy AlCuMgPb, AlZn5,5MgCu etc. Brass CuZn39Pb3, CuZn40Pb2 etc. Stainless steel 1.4301, 1.4305, 1.4571, 1.4401, 1.4101 etc. Steel Machining steel, St52, St37, C45, etc. Special steels Titan, Hastelloy, Copper, Bronze etc. Surface treatments may be done as follows: Galvanizing, nickel, brown, hot-dip galvanizing, phosphating, anodizing, chrome plating, painting, powder coating, plasma coating, sandblasting, Tuflok coatings. All common surfaces as VDA standard are possible (zinc-nickel, zinc flake). Heat treatments such as Plasma / gas nitriding, carbonitriding, hardening, carburizing, vacuum hardening, tempering etc.
Request for a quoteOTTO EICHHOFF GMBH & CO. KG
Germany
The economic adjustment to small batch sizes, we meet with our turned parts for the direct assembly in plastics and die-cast products. Any thread forms such as, thread-tapping (DIN7500), thread cutting (DIN 7513-7516) or KTG for direct screw in plastics are realized cost-effectively. Advantage is the elimination of high tooling costs, since no counter-thread in the workpiece (eg threaded inserts, nuts, etc.) is required because the direct assembly takes place directly into the workpiece. Only a given tube is required in order to screw it directly. Our turned parts replace previously cold formed parts used (so-called multi-station presses) which require high output volumes in order to achieve a reasonable price parts.
Request for a quoteNORELEM FRANCE
France
Body and flange plate EN AW5754. Guide shafts steel Version Body, hardcoated Flange plates, anodised. Guide shaft, hardened. Note Maintenancefree pneumatic linear modules with two precision steel shafts and ball guide bushing with wipers. Double acting cylinder drive. All fastening threads have threaded inserts. The as accessory available shock absorbers and proximity switches can be integrated (no protruding edges). Positive fit construction for hundred per cent reproducibility. Combinations in all sizes and stroke variants are feasible without adapter plates. Repeat accuracies of ±0.01 mm are possible. Specified loads apply by centred carriages. On request Available with locking cartridge as stroke deviation safeguard. Accessory See table for shock absorber, proximitiy switch and plug connector.
Request for a quoteNORELEM FRANCE
France
Case-hardened and black oxidised. Note: Positioning feet are used as supports, stops and thrust pads for fixtures and general machine and appliance construction. Drawing reference: Form A: External thread and flat face Form B: External thread and convex face Form C: External thread and serrated face Form K: External thread and carbide serrated face Form L: External thread and POM insert Form D: External thread and flat face Form E: External thread and convex face Form F: External thread and serrated face
Request for a quoteNORELEM FRANCE
France
Body carbon steel. Ball, ball bearing steel 1.2067. Form D: Ball with POM insert. Form H: Ball with POM insert. Form K: Ball with carbide insert. Form M has a carbide ball. Version: Body tempered and phosphated. Ball hardened. Form M ball nickel plated. Note: Self-aligning pads serve as stops, supports and thrust pads in fixture constructions. Ball secured against rotation. * Valid only if the minimum bore depth is observed. Drawing reference: Form C: with male thread, flattened ball, smooth. Form D: with male thread, flattened ball, with POM insert. Form F: with male thread, flattened ball, diamond grip. Form M: with male thread, flattened ball, with carbide insert. Form G: press fit, flattened ball, smooth. Form H: press fit, flattened ball, with POM insert. Form J: press fit, flattened ball, diamond grip. Form K: press fit, flattened ball, with carbide insert.
Request for a quoteSÜTHER & SCHÖN GMBH
Germany
Eye bolts acc. to DIN 444 with property class 8.8 for applications with high-tensile bearing means surface black passivated ATTENTION: The strength of the eye bolt must be in accordance to the strength of the wire rope. Item-no.: S05 00XX A0 ### 444 Insert the thread size for XX and the bold length for ### in the item-no. Other dimensions on request!
Request for a quoteSÜTHER & SCHÖN GMBH
Germany
Eye bolts acc. to DIN 444 galvanized surface ATTENTION: The strength of the eye bolt must be in accordance to the strength of the wire rope. * not acc. to DIN 444 ** Item-no.: S01 0020 A0 ### 000 *** Item-no.: S01 0027 A0 500 000 Item-no.: S01 00XX A0 ### 444 Insert the thread size for XX and the bold length for ### in the item-no.
Request for a quote1ST MACHINE TOOL ACCESSORIES
United Kingdom
Adjustable to suit 3 and 4 Segment Collets Used to insert and remove threaded collets. The number of segments the wrench suits can be easily adjusted
Request for a quote1ST MACHINE TOOL ACCESSORIES
United Kingdom
Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat Five High Accuracy Location Holes Cast Iron Sub Plate to suit rotary table or indexer. Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat with Locating Holes for precise loading and quick location.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
1ST MACHINE TOOL ACCESSORIES
United Kingdom
Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat and Parallel Cast iron gridded angle plate .Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat parallel and perpendicular for accuracy. To suit verticle or horizontal machining centre applications.
Request for a quote1ST MACHINE TOOL ACCESSORIES
United Kingdom
Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat and Parallel Threaded Holes for Side-Location Cast iron gridded cube with mounting holes. Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat parallel and perpendicular for accuracy. Holes for side location to allow precise loading and setting up of the tombstone.
Request for a quote1ST MACHINE TOOL ACCESSORIES
United Kingdom
Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat and Parallel Locating Holes for easy Location Cast iron fixture plate with mounting holes. Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat parallel and perpendicular for accuracy. Two dowel holes allow for precise loading and setting up of the fixture plate.
Request for a quote1ST MACHINE TOOL ACCESSORIES
United Kingdom
Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat and Parallel Threaded Holes for Side-Location Cast iron gridded cube with mounting holes. Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat parallel and perpendicular for accuracy. Holes for side location to allow precise loading and setting up of the tombstone.
Request for a quote1ST MACHINE TOOL ACCESSORIES
United Kingdom
Allignment Busing and Thread Hole for Quick Accurate Set-ups Ground Flat and Parallel Threaded Holes for Side-Location X-Shape allows for more side Clearance for Machining Cast iron gridded cross profile Tooling Column with mounting holes. Grid pattern with allignment bushes and threaded inserts for ease of set-up. Ground flat parallel and perpendicular for accuracy. Holes for side location to allow precise loading and setting up of the tombstone.
Request for a quoteKGA ENCLOSURES LTD
United Kingdom
Product Features: • Fully encapsulated chokes for use in custom designed suppression circuits. • Typical applications include the suppression of RFI generated by motors and switched mode power supplies etc. All chokes are fully encapsulated and feature single M4 threaded insert fixing. • Available in 10A, 15A and 25 Amps current rating with flying leads connection. • All products are RoHS compliant and approvals held include UL and cUL.
Request for a quoteBROADLEY JAMES LTD
United Kingdom
Broadley-James offers the widest range of autoclavable and steam sterilisable pH & redox electrodes available on the market today. Electrodes are available in a 12 mm body with a PG13.5 mounting thread and insertion lengths up to 420 mm. Connector options are industry standard S8, K9 or Variopin in both straight and right angle formats. The new F-800 Series offers a zero drift measurement with a noise resistant design and enhanced regulatory documentation.
Request for a quoteResults for
Threaded insert - Import exportNumber of results
25 ProductsCountries
Company type