Steel sheets - Import export

Inner ring, outer ring and rolling elements, bearing steel. Cage sheet steel. Labyrinth seal sheet steel. Lip seal NBR. Version 2Z = sealed both sides with noncontact labyrinth seals. 2RSR = sealed both sides with contact lip seals. Note Deep groove ball bearings accept high radial and axial loads. Axial loads are absorbed in both directions. The versions 2Z and 2RSR are lubricated for life with a high quality grease. The main dimensions of the deep groove ball bearings conform to DIN 6251. Dimensional and running tolerances correspond to tolerance class PN acc. to DIN 620. The radial internal clearance corresponds to the clearance CN acc. to DIN 6204. These tolerance classes are standard and well suited for most applications.

Steel sheet supplier

Steel metal plates, or cut-to-length sheets represent the common used steel material for several application sectors: construction equipment, street furniture, shelving systems, household appliances, engineering and automotive. Thanks to its unique fabrication network and quality system, Marcegaglia Baltics range of carbon steel sheets is fully compliant to these markets’ requirements in terms of grades, dimensions and mechanical properties.

System perfection. The new compact enclosure AX (sheet steel) offers maximum data quality and consistency in engineering, and flexibility and safety in assembly and interior installation. AX Compact enclosure, WHD: 380x300x210 mm, sheet steel, with mounting plate, single-door, with one cam lock

The small enclosure KX, terminal box KX, without a gland plate allows for flexible interior installation while maintaining a high protection category. The small enclosure KX, terminal box KX, without a gland plate allows for flexible interior installation while maintaining a high protection category. KX Terminal box, WHD: 150x150x120 mm, sheet steel, without mounting plate, with cover, without gland plate.

- Wide range of steel grades: structural, cold forming, HSLA, etc. - In coils or cut-to-length - Standard os curtomized sizes

Stainless steel tubes 1.4301 304L 1.4404 316L 1.4571 316TI, 321, 1.4541 Stainless steel round bars 1.4301 1.4404 1.4571 1.4541 1.4021 1.4006 1.4104 Welded and seamless stainless steel tubes 904L 1.4539 UB6 - Full stainless steel round bars UB6 904L 1.4539 Refractory tubes and round bars 309 1.4828 1.4833 310 310S 1.4841 1.4845- Duplex tubes UNS S31803 1.4462 Super duplex tubes UNS S32750 S32760 1.4410 1.4501 Duplex super duplex full round bars 1.4462 1.4410 1.4501 Stainless steel sheets 1.4301 304L 1.4404 316L 1.4571 316TI, 321, 1.4541 Refractory sheet 309 1.4828 1.4833 310 310S 1.4841 1.4845- Duplex sheets UNS S31803 1.4462 Super duplex sheets UNS S32750 S32760 1.4410 1.4501 Stainless steel sheets UB6 904L 1.4539 Alloy tubes 600; 601; 800; 825 Hastelloy C276 - Tubes and sheets 2.4816; 2.4851; 2.4856; 2.4360 Duplex super duplex stainless steel flanges 904L UB6 1.4539

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

TYPE OF PROCESS ROUTE AND SURFACE FINISH OF PLATES AND COILS EN 10088-2: 2H, 2D, 2B, 2R, 2G, 2J, 1D, 2E, 2K. Tinned or nickel plated strips can be supplied under a commercial agreement. The quality of the surface of a strip is characterised by the following approximate average surface roughness values: Ra < 0.3 µm for tensile strength levels of +C1150 and above. Ra < 0.5 µm for tensile strength levels ranging from +C700 to +C1000.

SURFACE FINISH. APPROVED FINISHES EN 10202 Bright, Fine stone, Stone, Silver, Matt COATING. PRECISE VALUES FOR TIN COATINGS EN 10202 HICKNESS TOLERANCES Thickness tolerances and edge reduction according to EN 10202 The thickness of the material must meet the following requirements: a) Deviation from the agreed thickness, measured on the centre line of the strip, must not exceed ± 5%. b) Deviation from the agreed thickness, measured at any point at a distance of no less than 6 mm from the sheared edge, must be between +5% and -8%. WIDTH TOLERANCES Other, closer dimensional tolerances are possible under a commercial agreement. EDGE CAMBER TOLERANCES Tolerances for edge bending under commercial agreement.

SURFACE FINISH. APPROVED FINISHES EN 10202 Bright, Fine stone, Stone, Silver, Matt COATING. PRECISE VALUES FOR TIN COATINGS EN 10202 HICKNESS TOLERANCES Thickness tolerances and edge reduction according to EN 10202 The thickness of the material must meet the following requirements: a) Deviation from the agreed thickness, measured on the centre line of the strip, must not exceed ± 5%. b) Deviation from the agreed thickness, measured at any point at a distance of no less than 6 mm from the sheared edge, must be between +5% and -8%. WIDTH TOLERANCES Other, closer dimensional tolerances are possible under a commercial agreement. EDGE CAMBER TOLERANCES Tolerances for edge bending under commercial agreement.

FINISHES: SURFACE QUALITY PROPERTIES OF THE COATINGS GALVANISED STEEL according to EN 10142 Check our website for coating mass, coating finish, surface quality and protection surface treatment. If the customer does not require the surfaces to be oiled and/or chemically passivated, this must be clearly indicated when requesting the quote and placing the order. THICKNESS TOLERANCES Thickness tolerances according to EN 10143 for nominal widths. WIDTH TOLERANCES Tolerances on wide strips obtained by longitudinal cutting of a width of less than 600 mm.According to Standard EN 10143 of: w < 125; 125 w < 250; 250 w < 400; 400 w < 600. Other, closer dimensional tolerances under a commercial agreement. SAG TOLERANCES Edge curve tolerances under commercial agreement

FINISHES: SURFACE QUALITY PROPERTIES OF THE COATINGS GALVANISED STEEL according to EN 10142 Check our website for coating mass, coating finish, surface quality and protection surface treatment. If the customer does not require the surfaces to be oiled and/or chemically passivated, this must be clearly indicated when requesting the quote and placing the order. THICKNESS TOLERANCES Thickness tolerances according to EN 10143 for nominal widths. WIDTH TOLERANCES Tolerances on wide strips obtained by longitudinal cutting of a width of less than 600 mm.According to Standard EN 10143 of: w < 125; 125 w < 250; 250 w < 400; 400 w < 600. Other, closer dimensional tolerances under a commercial agreement. SAG TOLERANCES Edge curve tolerances under commercial agreement

11SMn30 EN 10087

HCXXXLA EN 10268

DC01 DC03 DC04 DC05 DC06 EN 10130 / EN 10139

THICKNESS TOLERANCES : Thickness tolerances according to EN 10051 for nominal widths. WIDTH TOLERANCES: Width tolerances according to EN 10051 for nominal widths Other, closer dimensional tolerances on request. EDGE CAMBER TOLERANCES: Sag tolerances according to EN 10051 for pickled hot-rolled strips will be agreed when placing the order. RIPPLE - LONGITUDINAL FLATNESS: The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm on 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES : Thickness tolerances according to EN 10051 for nominal widths. WIDTH TOLERANCES: Width tolerances according to EN 10051 for nominal widths Other, closer dimensional tolerances on request. EDGE CAMBER TOLERANCES: Sag tolerances according to EN 10051 for pickled hot-rolled strips will be agreed when placing the order. RIPPLE - LONGITUDINAL FLATNESS: The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm on 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES : Thickness tolerances according to EN 10051 for nominal widths. WIDTH TOLERANCES: Width tolerances according to EN 10051 for nominal widths Other, closer dimensional tolerances on request. EDGE CAMBER TOLERANCES: Sag tolerances according to EN 10051 for pickled hot-rolled strips will be agreed when placing the order. RIPPLE - LONGITUDINAL FLATNESS: The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm on 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.