Steel screws - Import export

Rest pads are for supporting machined and non-machined parts. They can also be used as stops and thrust pads in fixtures and toolmaking. Studs or grub screws can be screwed and glued into the tapped hole D to make a rest pad with external thread.

Hardened and ground. Top face without centerbore. Note: If more than one rest pad is used, the support height can be reground. Rest pads can also be used as feet for jigs and fixtures.

Worm screw steel. Worm wheel CuZn37Mn3Al2PbSiS40. Version Worm screw with righthand pitch, casehardened HV 620 – 700, flanks and hole ground. Note for ordering Wheels/screws can only be combined to form a worm gear if they have the same centre distance and transmission ratio. Note A worm gear consists of a worm screw (shaft) and a worm wheel. Suitable for forming worm drives with a 90° shaft angle. A worm drive enables very large speed reduction ratios with a single stage. The toothing has the flank shape K. The engagement angle is 15°. The worm gears are prebored. The stated T2 output torques are the permissible output torques on the worm wheel. These apply for an input speed of 2800 rpm of the worm screw. The worm gears are suitable for continuous operation at high speeds and high torques. Attention 22500171002 Screw polished only. 22500172002 Worm wheel with helical gear toothing.

The floating joint unit is a bolt for connecting two components, that permits a desired movement of those components in relation to each other. The floating joint unit is mainly used when: a temperature change alters the dimensions of a component assembly inaccuracies occur manufacturing tolerances must be compensated for the position of the components varies due to dynamic loads

Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note By telescopic slides with full extension, the travel is roughly equal to the installed length, which ensures greater comfort and accessibility. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 80,000 cycles. Not suitable for horizontal mounting. The head height of the fastening screws should not exceed 1.8 mm otherwise there is a risk of collision with other parts of the slide. Advantages Low slide thickness Light running Precise guidance for high lateral stability

Slides steel. Ball cages steel. Balls, steel. Version Slides electro zincplated. Ball cages, electro zincplated. Balls hardened. Note for ordering Sold in pairs. Note On telescopic slides with partial extension both sides, the travel is less than the installed length. Latches in open position on both sides. The dynamic load capacity of the telescopic slides indicates the maximum load rating of a vertically mounted slide pair when the entire extension length is used. The load capacity specified is calculated with a slide spacing of 450 mm and is based on the maximum value with 50,000 cycles. The load capacity is ca. 75% lower by horizontal mounting. The head height of the fastening screws should not exceed 2.5 mm otherwise there is a risk of collision with other parts of the slide. Advantages Pulls out in both directions Latches in open position on both sides Light running

Polyethylene. Screw, steel. Note: Levelling feet with hexagonal base. Rigid version.

Self-tapping screw for fastening, connecting sheet metal and metal profiles up to 0.9 mm Head: hexagonal with a shoulder, straight slot

Roofing self-tapping screw for metal DIN-EN-ISO 15480 (old - DIN 7504-K) with an EPDM washer 2.4-2.8 mm thick Standard Head: hexagonal with a shoulder, , turnkey 8 (D-5.5) or 10 (D-6.3) mm, a marking mark in the form of the letter "X" is stamped on the cap

Hex Key For Steel Tamperproof Screws

Six Lobe Bit For Steel Tamperproof Screws

Torx Bit For Stainless Steel Tamper Proof Screws

Hex Lobe Wrench For Steel Tamper Evident Screws

Hexagonal Bit For Steel Tamper-Resistant Screws

During re-machining, a cutting tool is used to remove material from a workpiece in order to shape or surface it as required. We offer re-machining (turning, twisting) as wage work. The following machining operations we offer: Turn thin stem, pins and tips Screw punctures, approaches and undercuts Heads of screws / cold shaped parts machining process (turning) further machining operations are possible on request. Our curve-controlled automatic Audrema lathes offer you further possibilities of finishing cold-moulded parts. These automatic lathes are designed to achieve maximum precision and reproducibility at high throughputs. Short loading and unloading times permit economical production of medium-sized and large series.

The surface of the hexagon head bolt is polished and, with regard to design optimised for the use in hygienic environments. The bolt head is convex on the top face and the collar has a conical formed top surface. Instead of troublesome embossing or indentations, the bolt head is smooth with a surface finish of Ra 0.8 µm. Dirt and residue from products or cleaners seldom adheres and easy cleaning is ensured.

Self-locking trapezoidal thread, spindle has end lock. Note: The through hole allows easy clamping and positioning of the workpiece. Drawing reference: 1) centring hole for 02210

Hook clamps and clamping screw carbon steel, tempered.

Maintenance-free high quality link bushings. Sustainable constant use of force during opening and closing. Optimum stability through the conical, U-profile clamping arm. Accessory: 05280 Protective caps 07111 Ball-end thrust screws, stainless steel 07119 Thrust screws, stainless steel 07120 Grub screws with thrust point DIN 6332 07140 Thrust pads DIN 6311 Drawing reference: 1) stop pin position 1 2) stop pin position 2

RIFBOLT blind rivet studs consist of a sleeve and a screw, which are joined together by welding or crimping. As special production components we can use different lenghts and types of screws can be used as well as almost every rivet nut sleeve. Blind rivet studs offer a multiple use. They can — connect different working pieces, — install a thread into components and — fix additional parts to the screw.

Bottle made of RPET, 600ml capacity, BPA free. Stainless steel screw cap, with carrying strap. Available in a wide range of colours. Made from recycled plastic, to encourage the reuse of plastic waste and help the sustainability of the planet. 600 ml RPET/ Stainless Steel

truss head shoulder screw thread: 8-32 UNC-2A head height: 0.170 +/- 0.015 inch, head diameter: 0.500 +/- 0.015 inch rod length: 0.875 +/- 0.062 inch groove width: 0.064 +/- 0.015 inch, depth: 0.074 +/- 0.015 inch material: steel surface finish: zinc plated Soochow Advance Industries Co., Ltd., (website: www.sai-parts.com) supplies custom OEM mechanical parts, industrial fasteners, screws, bolts, nuts, industrial fittings, electronic hardware by precision CNC machining, CNC turning, CNC milling, CNC engineering.

Steel fasteners

Round steel / Square steel, Flat steel , L cornier profile , IPE Steel and much more

Side panels, screw-fastened, sheet steel, for VX. VX Side panel, screw-fastened, for HD: 1800x800 mm, sheet steel

Adjustable to suit 3 and 4 Segment Collets Used to insert and remove threaded collets. The number of segments the wrench suits can be easily adjusted

No need to remove your 3 jaw or collet chuck Side actuated for thru or blind bores Use the same mandrels, sleeves and locators as the hydraulic systems A great option for low/medium-volume production. KEM Series includes a manually-operated expanding mandrel actuator incorporating a precision-ground 38mm diameter spigot for mounting in collet or jaw chucks. These models utilise the same precision mandrels, expanding sleeves and locators as our CNC Expanding Mandrels. They are side-actuated with an included square-drive key so that they can accommodate parts with blind bores as well as those with thru-holes. Precision-ground for high accuracy in squarenesss and concentricity, If higher accuracy is needed the mandrel can be clocked-in once the unit is gripped in a chuck.

Quick change jaws for fast setups Hardened and precision ground for wear resistance and accuracy Ideal for demanding clamping conditions and high clamping forces Adapts the OneLok to accept older bolt-on soft jaws Jaw spacers for OneLok that fit 5OL1540 and 5OL1550 and well as the previous generation of OneLok. These jaws are hardened and precision ground for strength and accuracy. The BoltFast mechanism means they can be changed in seconds. The holes in these jaws allow the re-use of standard bolt-on jaws.

Quick change jaws for fast setups Hardened and precision ground for wear resistance and accuracy Ideal for demanding clamping conditions and high clamping forces Plain hard jaws for OneLok that fits 5OL1540 and 5OL1550 and well as the previous generation of OneLok. These jaws are hardened and precision ground for strength and accuracy. The BoltFast mechanism means they can be changed in seconds.