Sensor technology - Import export

Housing thermoplastic. Version: Operating principle: Magnetic. Rating: IP67. Note: If the actuator is within the switching range (safety door closed), the safety contacts and, if applicable, the signal contacts of the safety switch are activated. The contact is thus closed via a magnet (magnetic field). Form A: Actuator on one level to the safety switch. Form B: Actuator offset by 90° to the safety switch.

Housing Form A plastic. Housing Form B die-cast zinc alloy. Active face POM. Housing Form C high-alloy stainless steel Version: Voltage: U = 10 – 30 V DC Function: Normally open Switch type: PNP Mounting type: flush Security type: IP 67 Note: Non-contact, functions wear-free with high switching frequency and accuracy. Non-sensitive to vibrations, dust and moisture. Inductive sensors record all metals without contact. Form C enables screw fastening in a T-slot. Is safe and saves space as the proximity switch lays flush in the slot. Short-circuit proof and reverse-polarity protected.

Electric-hydraulic setting tool for stationary automated or hand-held processing of blind rivet nuts and studs. Perfect combination of high setting force, slim design and low weight. The narrow design allows a small centre distance for modular design. — Process monitoring DMSD 2G Displacement encoder with resolution 0.01 mm Sensor technology force measurement via hydraulic pressure — Hydraulic connection for pressure intensifier — Mechanical connection — Tolerance compensation Position offset 1.5 mm Angular misalignment 8° — Electric motor Monitoring of torque and rotationangle during spindle mounting and dismounting — Hydraulic hollow piston cylinder stroke 12 mm setting force up to 58 kN — Quick-change system For fast handling and low-maintenance operation Low tool costs by using DIN screws as mandrel (option)

The WEC/WDEC410 Series Single and Dual Input Electrodeless Conductivity Controllers measure conductivity of a solution via an encapsulated, non-contacting sensor to control replenishment pumps and alarms. They may be installed in a variety of very harsh chemical control applications, including oily cleaner baths, chromates, rinse tanks, fume scrubbers and other concentrated chemicals up to a conductivity of 1000 mS/cm. Four conductivity ranges may be selected to configure the controller over a wide range of applications. Choice of measurement units is µS/cm, mS/cm, ppm and % concentration. The non-contacting, toroidal sensor technology is immune to thin coatings and the contamination and calibration problems that direct contacting sensors are prone to. Integrated datalogging is available to validate performance. With a USB memory stick data and event logs that include conductivity measurements, temperature and relay status can be extracted. Then download log files from the USB stick

Measurement and control In this sector, MPT represents the interests and products of WALCHEM Corporation in Holliston, Massachusetts (USA). WALCHEM is a leading manufacturer of sensor technology and controllers for the surface technology and for the water treatment technology, including pH-, redox and conductivity controllers as well as special controllers for the cooling-water and boiler water conditioning. Besides the measuring transducer, these controllers include also a control program, adapted to the respective application. Monitoring, alarming – control and telecontrol systems By default, WALCHEM’s WebMaster has available sensors and data amplifiers for various physical parameters. Using the integrated program the parameters can be linked to each other and to control parameters. Via telephone modem and Ethernet board the user is provided with information such as alarm messages and off-limit conditions worldwide.  Measuring and control technology for dosing liquid media in

Usually, acceleration sensors with ICP®/IEPE technology are used for vibration monitoring. Sensors for series use are particularly suitable if a large number of measuring points are to be monitored. The low-cost sensor models, where the sensor model 627A01 belongs, can be integrated permanently into monitoring systems or used in conjunction with a portable data collector/analyzer for route-based monitoring. The accelerometer presented here, model 627A01, can be used in ambient temperatures up to 121 °C. If the operating conditions require it, this model is also available with EX approval or with SIL-2 declaration. All sensors are supplied with 1-point calibration according to ISO 17025. The industrial accelerometer, model 627A01, is equipped with a quartz sensing element. — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.33 ... 10,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on top For an individual offer, please contact us directly

Acceleration sensors with ICP®/IEPE technology are usually used for vibration monitoring. Sensors for series use are particularly suitable if a large number of measuring points are to be monitored. The low-cost sensor models, where the sensor model 627A01 belongs, can be integrated permanently into monitoring systems or used in conjunction with a portable data collector/analyzer for route-based monitoring. The accelerometer presented here, model 602D01, can be used in ambient temperatures up to 121 °C. If the operating conditions require it, this model is also available with EX approval or with SIL-2 declaration. All sensors are supplied with a 1-point calibration according to ISO 17025. — With through hole — Measuring range 50 g — Sensitivity 100 mV/g — Frequency range 0.5 ... 8,000 Hz — Single-point calibration at 100 Hz — 2-pin connection socket on the side Please contact us directly for an individual offer.