Precision tools - Import export

The 2200PTP Series Wireless Power Tools are designed to work with the Global 400 and Global 400mp controller systems. These wireless tools are designed for industrial assembly use. The tool is completely dependent on the Global 400/400mp for directions and torque results reporting. Details on learning and programming the tool through the Global 400/400mp controllers may be found in the controller manual. Models 2200PTP-18: 3-18 Nm / 50-100 RPM 2200PTP-24: 6-24 Nm / 50-600 RPM Key Highlights Report torque/angle values with the results Kits come with side handle

The 2100PTP Series Wireless Power Tools are designed to work with the Global 400 and Global 400mp controller systems. These wireless tools are designed for industrial assembly use. The tool is completely dependent on the Global 400/400mp for directions and torque results reporting. Details on learning and programming the tool through the Global 400/400mp controllers may be found in the controller manual. Model 2100PTP-12: 3-12 Nm / 700-100 RPM Key Highlights Adjustable clutch sets torque limit Report OK/NOK results Kits come with an adjustment tool Double hit detection

The 2100PTA Series Wireless Angled Power Tools are designed to work with the Global 400 and Global 400mp controller systems. These wireless tools are designed for industrial assembly use. The tool is completely dependent on the Global 400/400mp for directions and torque results reporting. Details on learning and programming the tool through the Global 400/400mp controllers may be found in the controller manual. Models 2100PTA-45: 18-45 Nm / 210-300 RPM 2100PTA-90: 40-90 Nm / Fixed 100 RPM Key Highlights Adjustable clutch sets torque limit Report OK/NOK results Kits come with an adjustment tool Double hit detection Adjustable speed defined by controller parameter (2100PTA-45 only)

Steel housing. Nitrile rubber seal. Preloaded highaccuracy bearings with a 60° thrust angle. The bearings accept both radial and axial forces from both directions. Due to their preload, the angular contact ball bearings provide a high level of stiffness, excellent concentricity, precise tool positioning and repeatability. The integrated lowfriction seal effectively keeps dirt away from the bearing, thereby ensuring excellent operating safety and a long service life. The bearing friction coefficient Mrl is a reference value. The moment of inertia corresponds to that of the rotating inner ring. The limiting speeds are applicable after grease is applied. Technical data All bearings are supplied ready for mounting with lubricating grease type KE2P35 acc. to DIN 51825. Housing and shaft tolerances correspond to roundness tolerance class IT2 and perpendicularity tolerance class IT4.

1. 9KW air-cooling ATC spindle motor: Long working life, easy maintenance (HSD brand from Italy for option).2. Taiwan Delta Inverter: Guarantee the variety working speed and protect the spindle very well.3. Big steel square tube structure,by seamless welding and hardening treatment, guarantee it to be strong, reliable and durable, with large bearing capacity and long working life.4. Japan Yaskawa driving System with Shimpo reducer: With highly control precision and high speed, reliable and stable.5. Helical rack and pinion: quiet running, greater accuracy, smoother cutting and allows greater accelaration and feeding rates, longer lifetime because of smaller wearing force.6. High precision Taiwan TBI ball screw and Taiwan Hiwin linear square rails, which move smoothly to ensure the machining precision.7. Disc tool magazine, with Tool holders 12pcs, effectively improve working efficiency.

For sophisticated decorative materials Press laminating is mainly used to process materials that are unsuitable for vacuum processes, such as textiles, materials with and without foam backings or non-stretchable cover materials like leather or Alcantara. Processing these materials requires high quality tooling and machinery to ensure the quality of the grain, the soft touch and the color remain intact. The decorative element and the substrate are usually laminated together by being pressed between two hard instruments. Precise decor positioning and tool arrangements ensure optimal laminating conditions. Other forms of laminating include leather laminating and membrane laminating, which combines press laminating, edge folding, trimming.

Compatible with large, readily available, range of jaws Allows for holding of larger components Upto 20% more speed and grip force than conventional chuck Standard Accessories AvailableKitagawa chucks are manufactured from high grade alloy steel. Three jaw wedge style power chucks deliver up to 20% more speed, gripping force and bore size when compared to conventional chucks. These larger style chucks provide the higher grip forces required for doing large work. B-A series chucks are supplied with a blank drawnut as standard with a set of T-nuts and adaptor plate.

2+2 Independent jaws give contact with all four jaws Long stroke grip compounets with variable size Ideal for square or elliptical parts Compatible with large, readily available, range of jaws Kitagawa chucks are manufactured from high grade alloy steel. The Kitagawa HW series are four jaw chucks but unlike conventional four jaws it works off a 2+2 system clamping two jaws indapendently garentees gripping with all four jaws unlike standard chucks. HW series chucks are supplied with blank drawnut and a set of t-nuts as standard.

For example- Full System Chuck Adaptor Threaded Connector Drawtube Cylinder Adaptor Hydraulic Rotating Cylinder Anti Rotation Bracket Drain, Hoses and Fittings Part systems can be either: Front End- Chuck Adaptor Threaded Connector Drawtube Rear End: Drawtube Cylinder Adaptor Hydraulic Rotating Cylinder Anti Rotation Bracket Drain, Hoses and Fittings Or indeed any part(s) there of.

Included in this range- Large bore 3 & 4 Jaw Self Centring Chucks- Ø500-1800mm steel body cast iron available Ø500-630mm centring tolerances according to UNE 15-430-94/ISO 3089:1991 norm 4 jaw independent chucks with one piece jaws- Ø500-1500mm cast iron or steel body solid reversible jaws direct mounting 4 jaw independent chucks with two piece jaws- Ø500-1500mm cast iron or steel body two piece jaws according to ASA norms jaws direct mounting heavy duty 4 jaw independent chucks- Ø600-2000mm heavy duty steel body two piece jaws according to ASA norms jaws long master jaws for added rigidity direct mounting 3 and 4 jaw self centring VTL chucks- Ø700-1800mm specially designed for vertical lathes steel body central cover and long base jaws covering the spindle nose of the lathe induction hardening of all gliding areas 3 jaw oil country self centring chucks- Ø500-1000mm forged steel body extra heavy duty American Standard, hard top and master jaws

Ideal for irregular shaped components Soft jaws included with the chuck Better clearance on speicalist parts The JT series scroll chuck provides the optimum solution for gripping valves, pipe joints and other irregularly shaped components. JT series scroll chuck includes one set of soft jaws.

Usefull for thin wall parts High Rigidity, durability and rotational speed Quality steel use for corrosion resistance Cross guide reduces runout and distortion Kitagawa JS07 4-Jaw Scroll Chuck. The JS series scroll chuck provides the optimum solution for gripping valves, pipe joints and other irregularly shaped components.

Quality steel use for corrosion resistance High Rigidity, durability and rotational speed Cross guide reduces runout and distortion Comes with internal and external jaws Scroll chuck with integrated jaw (Straight recess) includes each one set of internal jaws and external jaws as standard. JN models cannot use soft jaws. When the soft jaws are used for SC-F type, use the chuck of lower specification. (SC-3, 4, 5, 14, 16 are made of cast iron and JN-6, 7, 9, 10 and 12 are made of steel.)

Quality steel use for corrosion resistance High Rigidity, durability and rotational speed Cross guide reduces runout and distortion Two piece jaws for quicker and easier jaw change over Scroll chuck with 2 piece Jaw (Straight Recess) - 3 Jaw Scroll Chuck featuring steel body construction to increase body rigidity and improved durability.

Cross guide reduces runout and distortion High Rigidity, durability and rotational speed Two piece jaws for quicker and easier jaw change over Direct mount to short taper so adapter isn't needed 3 Jaw Scroll Chuck featuring steel body construction to increase rigidity and improved durability. The JN-RA series have short tapers built-in, therefor adapters are not needed. Chucks are supplied with standard hard jaws with soft jaws available if needed.

Cross guide reduces runout and distortion Ideal for irregular shaped components Independent jaws allow for off centre holding Kitagawa chucks are manufactured from high grade alloy steel. The IC series are four jaw independent chucks with front mount holes. IC series chucks are supplied with a set of hard jaws.

Direct mount to short taper so adapter isn't needed Cross guide reduces runout and distortion Ideal for irregular shaped components Independent jaws allow for off centre holding Kitagawa IA 4-Jaw Closed Centre Chuck have a steel body and direct mount. Supplied with reversible hard jaws for ID and OD gripping.

Round, Hexagon, Square or Emergency types available Available in Smooth or Serrated Clamping tolerance of +/- 0.5mm Counter boring and special profile shapes are available upon request DC Varibore Collets have the same accuracy specification as spring collets whilst maintaining a gripping range of +/- 0.5mm. Supplied with either smooth or serrated gripping surface. Serrated collets are ideal for aggresive first operation gripping of rough bar work.Vulcanized rubber between the hardened steel collet segments provides excellent protection against coolant and chip ingress. Counter boring and special profile shapes are available upon request.

Round, Hexagon, Square or Emergency types available Available in Smooth or Serrated Clamping tolerance of +/- 0.5mm Counter boring and special profile shapes are available upon request DC Varibore Collets have the same accuracy specification as spring collets whilst maintaining a gripping range of +/- 0.5mm. Supplied with either smooth or serrated gripping surface. Serrated collets are ideal for aggresive first operation gripping of rough bar work.Vulcanized rubber between the hardened steel collet segments provides excellent protection against coolant and chip ingress. Counter boring and special profile shapes are available upon request.

Round, Hexagon, Square or Emergency types available Available in Smooth or Serrated Clamping tolerance of +/- 0.5mm Counter boring and special profile shapes are available upon request DC Varibore Collets have the same accuracy specification as spring collets whilst maintaining a gripping range of +/- 0.5mm. Supplied with either smooth or serrated gripping surface. Serrated collets are ideal for aggressive first operation gripping of rough bar work. Vulcanized rubber between the hardened steel collet segments provides excellent protection against coolant and chip ingress. Counter boring and special profile shapes are available upon request.

Round, Hexagon, Square or Emergency types available Available in Smooth or Serrated Clamping tolerance of +/- 0.5mm Counter boring and special profile shapes are available upon request DC Varibore Collets have the same accuracy specification as spring collets whilst maintaining a gripping range of +/- 0.5mm. Supplied with either smooth or serrated gripping surface. Serrated collets are ideal for aggressive first operation gripping of rough bar work. Vulcanized rubber between the hardened steel collet segments provides excellent protection against coolant and chip ingress. Counter boring and special profile shapes are available upon request.

Round, Hexagon, Square or Emergency types available Available in Smooth or Serrated Clamping tolerance of +/- 0.5mm Counter boring and special profile shapes are available upon request DC Varibore Collets have the same accuracy specification as spring collets whilst maintaining a gripping range of +/- 0.5mm. Supplied with either smooth or serrated gripping surface. Serrated collets are ideal for aggressive first operation gripping of rough bar work. Vulcanized rubber between the hardened steel collet segments provides excellent protection against coolant and chip ingress. Counter boring and special profile shapes are available upon request.

2mm Range per Collets Sizes Up To 42mm Across Flats Smooth Bore as Standard, Other Finishes Available Special Profiles Available D677 Varibore square collets are to suit 60mm capacity collet chucks. Also known as M677, these collets have a 2mm range. Supplied smooth as standard we can supply with alternate finishes and in special profiles. D677 suit the following collet chucks- Klamp CRL60 Klamp QCRL60 Crawford CDC60 Crawford CDC-60-S Crawford QCD-60

2mm Range per Collets Sizes Up To 62mm Capacity Spiral Serration as Standard, Other Finishes Available Special Profiles Available D677 Varibore round collets are to suit 60mm capacity collet chucks. Also known as M677, these collets have a 2mm range. Supplied spiral serration as standard we can supply with alternate finishes and in special profiles. D677 suit the following collet chucks- Klamp CRL60 Klamp QCRL60 Crawford CDC60 Crawford CDC-60-S Crawford QCD-60

2mm Range per Collets Sizes Up To 52mm Across Flats Smooth Bore as Standard, Other Finishes Available Special Profiles Available D677 Varibore hexagon collets are to suit 60mm capacity collet chucks. Also known as M677, these collets have a 2mm range. Supplied smooth as standard we can supply with alternate finishes and in special profiles. D677 suit the following collet chucks- Klamp CRL60 Klamp QCRL60 Crawford CDC60 Crawford CDC-60-S Crawford QCD-60

2mm Range per Collets Sizes Up To 30mm Across Flats Smooth Bore as Standard, Other Finishes Available Special Profiles Available D673 Varibore square collets are to suit 42mm capacity collet chucks. Also known as M673, these collets have a 2mm range. Supplied smooth as standard we can supply with alternate finishes and in special profiles. D673 suit the following collet chucks- Klamp CRL42 Klamp QCRL42 Crawford CDC42 Crawford CDC-42-S Crawford QC-42

2mm Range per Collets Sizes Up To 42mm Capacity Spiral Serration as Standard, Other Finishes Available Special Profiles Available D673 Varibore round collets are to suit 42mm capacity collet chucks. Also known as M673, these collets have a 2mm range. Supplied spiral serration as standard we can supply with alternate finishes and in special profiles. D673 suit the following collet chucks: Klamp CRL42 Klamp QCRL42 Crawford CDC42 Crawford CDC-42-S Crawford QC-42

2mm Range per Collets Sizes Up To 36mm Across Flats Smooth Bore as Standard, Other Finishes Available Special Profiles Available D673 Varibore hex collets are to suit 42mm capacity collet chucks. Also known as M673, these collets have a 2mm range. Supplied smooth as standard we can supply with alternate finishes and in special profiles. D673 suit the following collet chucks- Klamp CRL42 Klamp QCRL42 Crawford CDC42 Crawford CDC-42-S Crawford QC-42

Change collets in a matter of Seconds DCD collet changing gun are required for the changing of DC collets. The gun collapses the collet down so it can be placed into the collet and released into position.